• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.275-281
• /
• 2013

This study was conducted to increase the amount of bio-hydrogen production from microalgae(Chlorella vulgaris) in batch reactors by thermal pre-treatment. The optimization of thermal pre-treatment was conducted using statistic experimental design of response surface methodology. Two experimental parameters of temperature and reaction time were considered. The optimization condition was founded at the coded variables of <0.52, -0.07> corresponding to the experimental of heating temperature of $95.6^{\circ}C$ and reaction time of 57.9 min, respectively. Under the optimal condition, the maximum hydrogen production was predicted to 25.3mL $H_2/g$ dry cell weight (dcw), which was 9.1 times higher value of control(2.8mL $H_2/g$ dcw).

• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.385-394
• /
• 2007

In this study, the effect of molding condition on the tensile properties for plain woven hemp fiber reinforced green composite was examined. The tensile properties of the composite were compared with those of the plain woven jute fiber composite fabricated by the same process. Emulsion type biodegradable resin or polypropylene sheet was used as matrix. The composites were processed by the compression molding where the molding temperature and its heating time were changed from 160 to $190^{\circ}C$ and from 15 to 25 min, respectively. The following results were obtained from the experiment. The tensile property of hemp fiber reinforced polypropylene is improved in comparison with polypropylene bulk. The strength of composite is about 2.6 times that of the resin bulk specimen. Hemp fiber is more effective than jute fiber as reinforcement for green composite from the viewpoint of strength. The molding temperature and time are suitable below $180^{\circ}C$ and 20 min for hemp fiber reinforced green composite. Hemp fiber green composite has a tendency to decrease its tensile strength when fiber content is over 50 wt%.

• Journal of Biomedical Engineering Research
• /
• v.11 no.2
• /
• pp.295-304
• /
• 1990

In order to use for artificial dental tooth (dental crowens) , new glass-ceramics material has been studied. Its basic composition and the condition of heat treatment for crystalization, mechanical and chemical properties were investigated. Adding of the LAS system composition in the basic glass, time and temperature for crystalization were shortened. Fracture toughness (kic)of samples heat treated at 90$0^{\circ}C$ for 2 hours is 2.5-2.6MN/m3/2, the optimum condition of heat treatment for artificial tooth is A and B samples heating to 75$0^{\circ}C$ for 2 hours, raising to 90$0^{\circ}C$ and maintaining at 90$0^{\circ}C$ for 2 hours and C sample heating to 75$0^{\circ}C$ maintaining at 75$0^{\circ}C$ for 2 hours. In acid and'alkali solution, chemical durability is excellent.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.76-81
• /
• 2009

Thermal desorption systems are designed to remove organic compounds from solid matrices such as soils, sludges and filter cakes without thermally destroying them. It is a separation technology, not a destruction technology. Since it is a thermal process, there is a common belief that temperature is the only significant parameter to be monitored. While it is true that better removal efficiencies are usually achieved at higher temperatures, other factors must be considered. Since the process is governed by mass transfer, heating time and the amount of mixing are also key parameters in optimizing removal efficiency. Thermal desorption have been successfully used for just about every organic contaminant found to date. It has also been used to remove mercury. In the present study, the numerical simulation has been performed to investigate the characteristics of heat transfer of LTTD(low temperature thermal desorption). The commercial software, AMESIM was applied for analyzing the heat transfer process in the LTTD.

• Journal of the Korean Ceramic Society
• /
• v.18 no.4
• /
• pp.257-261
• /
• 1981

The tendency of glass containing titanium-dioxide to separate into two phases can be attributed to a change of the coordination number of titanium from six to four on increase of temperature and to "freezing" of the high temperature four fold coordination on cooling of the melt. Addition of TiO2 to the basic glass 8.7 $Na_2O$ 22.4B2O3 68.9 $SiO_2$ was varied 5 to 25 parts. The phase separation in the temperature range of transformation was examined with each heating temperature and soaking time. As the experimental results, the most distinct phase separation were obtained from alkali extraction method when $TiO_2$ was added 15 parts. The apparant activation energy was 30.5 Kcal/mole by alkali extraction method derived from Arrhenius plots.ius plots.

• Culinary science and hospitality research
• /
• v.20 no.2
• /
• pp.54-64
• /
• 2014

In order to enhance the firmness of retorted onion, long time, low temperature blanching(LTLT) in calcium solution was conducted. Pre-heating onion in calcium solution significantly improved its texture after high temperature sterilization as compared to conventional blanching alone. The improvement of the firmness by the LTLT blanching is related to the formation of strongly cross-linkages between carboxyl groups and divalent cations($Ca^{2+}$) by the action of pectin methy-lesterase(PME) in onion. A maximum firmness of retorted onion was obtained at the condition of pre-heating at $70^{\circ}C$ for 120min in 0.5%calcium solution. This result supports that the activity of PME and the content of bonded calcium in onion were highest at $70^{\circ}C$. Additionally, the reaction of alkali calcium with various divalent cations such as $Mg^{2+}$ provided a function to hydrolyze pectin molecules, resulting in firmer retorted onion in various calcium agents. Further investigation should be carried out to determine the optimal condition for prevention of tissue softening of various retorted vegetables.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.57-60
• /
• 2005

This study discusses spalling and fire enduring performance of high performance concrete (HPC) RC column subjected to loading under heating for 3 hours. According to the test, both the plain concrete and the concrete attached with fire enduring PC panel exceed allowable temperature after 60 minutes due to the exposure of steel bar and falling off of concrete resulting from severe spalling failure. It leads to buckling of main bar and at the same time, occurrence of collapse of plain HPC column member is observed after 2 hours and 1 hour 40 minutes's exposure to fire, respectively. On the other hand, HPC applying both PP fiber of 0.1$\%$ by mass of concrete and PP fiber+lateral confinement by metal lath maintains their original cross section, which is satisfied with the 3 hours fire endurance criteria, by discharging internal vapour pressure and enhanced lateral confinement force.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.10 no.4
• /
• pp.304-315
• /
• 1981

This paper presents, the result of the study for the fluctuant temperature of the out-side air adopting the heat pump system in seoul, Taejean, Taegu, Busan and Jejeu among principle cities in korea for the purpose of checking the heating capacity, Heat pump capacity (outlet capacity), Coefficient of performance and running cost in comparison with the supporting the energy for the boiler's operation. According to the supply temperature changes of the out door coil by the out side air-return air mixing ratio, the Coefficient of performance is increased from 3. 1 to 5.0. Particularly, in Taegu, it is necessary to adopt the heat pump system against the supplement heat supply on the full outside air intake in January of the heating period, and it was recognized that the running cost is cheaper than that of the Boiler use. At the same time, if it is able to get $25\%$ of return air of the inside in the Seoul, it could be saved its costs when we use the supplementary boiler. And I think it is necessary to the development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.350-356
• /
• 2020

Purpose: This study is a non-equilibrium control-like experimental study that attempts to develop a nursing intervention plan and to present basic data by grasping the effect of the heating therapy nursing intervention program on patients entering the recovery room after surgery. Method: The subjects of the study were 31 in an experimental group and 31 in a control group who applied one heating therapy program located in D city. The warming therapy was conducted in a recovery room in the range of 38 to 43℃ through a heater. The general characteristics of the subjects were determined by real number and percentage, and a homogeneity test between the experimental group and the control group was determined by 𝑥²-test and independent t-test. The difference in body temperature, pain, and tremor over time between the two groups was determined by repeated measure ANOVA. Results: First, the results of repeated measurements immediately after surgery showed significant differences in body temperature, pain, and tremor between the two groups. Second, temperature comfort showed a significant difference. Conclusion: The results confirmed that there was a positive effect on the patient in the intervention of warming therapy after surgery.

• Journal of the Korean Society of Combustion
• /
• v.16 no.2
• /
• pp.40-46
• /
• 2011

The diesel pre-heater has being used in cabin heating and coolant heating of engine to reduce the engine warm up time for commercial vehicle. The pre-heaters are classified as diesel spray combustor and it forms diffusion flame. By using swirler, a recirculation flow of hot product gases is established near the fuel nozzle and it helps the maintaining of diffusion flame. The design difference of swirler can affect on reaction characteristics and temperature distribution inside pre-heater. The purpose of this study is the investigation of the effect of swirler configuration on combustion characteristics. To solve spray combustion problem, the Euler-Lagrange approach discrete model is used to track droplet trajectory and evaporation history. The PDF equilibrium model is used for chemical reaction model. These models are implemented into the FLUENT code.