• 대한기계학회논문집B
• /
• 제38권7호
• /
• pp.571-579
• /
• 2014

하절기 에너지 이용의 합리화를 위해서는 소형 열병합 발전의 설비이용률을 높일 수 있는 지역냉방의 보급이 확대되어야 한다. 지역냉방에는 흡수식 냉동기와 제습냉방기 있는데 상대적으로 낮은 열원을 사용할 수 있어 지역난방에 연계할 수 있는 제습냉방이 공동주택용으로 각광을 받고 있다. 본 논문에서는 고체제습제를 이용며 현열로터 대신에 히트펌프를 사용한 하이브리드 제습냉방 시스템의 주거환경에서의 성능 특성을 분석하였다. 실내공급공기, 실내리턴공기, 실외흡입공기, 재생열량, 소비전력을 측정하여 인터넷을 이용한 모니터링을 통하여 데이터를 분석하였다. 전체에너지는 외기온도가 증가할수록 감소하였고 냉방능력은 외기온도가 증가할수록 증가하고, 외기습도가 감소할수록 증가하는 경향을 보였다. 성능계수는 냉방능력과 유사한 경향을 보이는 것으로 분석되었다.

• 한국작물학회지
• /
• 제47권6호
• /
• pp.475-478
• /
• 2002

보리의 산물처리 확대를 위한 기초자료를 제공하고자 미곡종합처리장을 이용한 보리 산물처리시 품질변화와 생력효과를 조사 분석한 결과는 다음과 같았다. 1. 정립율은 2.5-2.2mm의 비율이 가장 많았으며, 건조방식에 따른 차이는 없었다. 2. 경도는 건조방식에 따른 차이는 없었고, 색도는 산물건조와 관행인 천일건조와 차이는 없었다. 3. 흡수율은, 고형용출물, 퍼짐성 등의 취반특성은 건조방식에 따른 차이는 없었다. 4. 산물처리에 의하여 관행의 ha당 46시간에 비하여 21시간으로 54.3%의 생력효과가 있었고, 수확 후 관리는 54.3% 생력화되었다. 5. 산물처리로 수확 후 관리노력이 관행에 비하여 ha당 25시간이 절감되어 101,83원의 경영비 절감효과가 있었다.

• 물과 미래
• /
• 제15권3호
• /
• pp.23-36
• /
• 1982

The stochastic variations and structures of time series data on water quality were examined by employing the techniques of autocorrelation function, variance spectrum, Fourier series, autoregressive model and ARIMA model. These time series included hourly and daily observation on DO, turbidity, conductivity pH and water temperature. The measurement was made by automatic recording instrument at Noryangjin and Dook-do located in the downstream part of Han River during 1975 and 1976. Hourly water quality time series varied with the dominant 24-hour periodicity, and the 12-hour periodicity was also observed. An important factor affecting 24-hour periodic variation of DO is believed to be photosynthesis by algae. These phenomena might be attributable to periodic discharges of municipal sewage. Noryangjin site showed the more distinct 12-hour periodicity than Dook-do site did, and tidal effect might be responsible for the difference. The water quality, as measured by DO and turbidity, was better in the afternoon compared with the quality in the morning. This change can be explained by the periodic variation of DO, temperature and the amount of municipal wewage discharge. It was also observed that the water temperature at Noryangjin was higher than the temperature at Dook-do. This difference might have been caused by the pollutants that were added to the section between two sites. The correlation coefficients between some of the variables were fairly high. For example, the coefficient was -0.88 between DO and water temperature, 0.75 between turbidity and river flow, and 0.957 between water temperature and air temperature. The lag time of heat transfer from the air to the water was estimated as 24 days. The first order auto-regressive model was appropriate for explaning standardized hourly DO time series. The ARIMA model of (1, 0, 0) type provided relatively satisfactory results for daily DO time series after the removal of significant harmonic value.

• 대한기계학회논문집A
• /
• 제38권7호
• /
• pp.809-815
• /
• 2014

최근들어 원자력 발전소에 유도 가열 공정으로 굽힌 배관을 적용하려는 동향이 있다. 이러한 유도 가열 굽힘 공정 동안의 열-기계적 메커니즘에 의해 잔류응력이 발생할 수 있다. 잔류응력은 균열 발생과 성장에 중요한 영향을 미치는 균열 구동력들 중의 하나이다. 그러나, 기존 연구들은 두께 변화, 타원도와 같은 기하학적 형상 변이에 집중하고 있는 반면 공정 변수가 잔류응력에 미치는 영향과 관련된 연구는 찾아보기 힘들다. 본 연구에서는 316 오스테나이트 스테인리스 강으로 제작된 유도 가열 굽힘 배관의 잔류응력 분포에 미치는 공정 변수의 영향을 유한요소 변수 해석을 통해 고찰하였다. 고찰결과, 굽힘 모멘트와 굽힘 각도는 잔류응력에 미치는 영향이 미미한 반면 유도 가열률과 이송 속도는 잔류응력에 상당한 영향을 미침을 확인하였다.

• Journal of Microbiology and Biotechnology
• /
• 제17권6호
• /
• pp.934-944
• /
• 2007

Paenibacillus polymyxa E681 is known to be able to suppress plant diseases by producing antimicrobial compounds and to promote plant growth by producing phytohormones, and secreting diverse degrading enzymes. In spite of these capabilities, little is known regarding the flow of information from the bacterial strain to the barley roots. In an attempt to determine the flow of information from the bacterial strain to barley roots, the strain was grown in the presence and absence of barley, and two-dimensional polyacrylamide gel electrophoresis (2D-PAGE) and MALDI-TOF mass spectrometry were used. 2D-PAGE detected approximately 1,000 spots in the cell and 1,100 spots in the supernatant at a pH 4-10 gradient. Interestingly, about 80 spots from each sample showed quantitative variations. Fifty-three spots from these were analyzed by MALDI-TOF mass spectrometry and 28 proteins were identified. Most of the cytosolic proteins expressed at higher levels were found in P. polymyxa E681 cells grown in the presence of barley rather than in the absence of barley. Proteins detected at a lower level in the surpernatant of P. polymyxa E68l cells grown in the presence of barley were lipoprotein, glucose-6-phosphate 1-dehydrogenase, heat-shock protein HtpG, spermidine synthase, OrfZ, ribonuclease PH, and coenzyme PQQ synthesis protein, and flagellar hook-associated protein 2 whereas proteins detected at a higher level in the surpernatant of P. polymyxa E681 cells grown in the presence of barley included D-alanyl-D-alanine ligase A, isopentenyl-diphosphate delta-isomerase, ABC transporter ATP-binding protein Uup, lipase. Many of the proteins belonging to plant-induced stimulons are associated with biosynthetic metabolism and metabolites of proteins and transport. Some of these proteins would be expected to be induced by environmental changes resulting from the accumulation of plant-secreted substances.

• 한국농공학회논문집
• /
• 제46권4호
• /
• pp.39-46
• /
• 2004

This experiment was carried out to study on the effect of surface coating on thermal insulation of farm structures to improve thermal resistance and reflective effect of solar radiation. Nine different types of experimental specimen were compared in the temperature variations of inside and outside; A, B, C, D. E and F types are box container and G, H and I types are drum container. The size of these containers is $1,500{\times}2,000{\times}2,500$ mm and ${\varphi}$ $280{\times}330$ mm, respectively. Specimen of 3-type box(A, B, C) is galvanized steel sheet of thickness 0.45 mm. D, E and F types are sandwich panel of the thickness 50 mm inserted with urethane, glass wool and polystyrene form, respectively. G, H and I types are paint pot using in general. The surface of A. D, E, F and I types didn't any treatment, B, C and G types were treated with thermal insulation coating on the outside surface(B, G) or the inside and outside surface(C). And H type was treated with water paint coating on the only outside surface. In general, the experimental results showed the following tendencies; In case of A, B and C types. it was found that the thermal insulation effect of types coated with thermal insulation coating was improved remarkably than that of no treatment. And the thermal insulation effect between steel sheet and sandwich panel type was nearly similar There was not a significant difference of thermal insulation effect between thermal insulation coating and water paint coating. In time of drum container filled with rough rice, The difference of heat transfer tendency and temperature variation among surface treatments was nearly similar that of box types of galvanized steel sheet. And there was time lag about 6 hours between the temperature of middle part of rice and that of inside or outside surface.

• Journal of Biosystems Engineering
• /
• 제36권5호
• /
• pp.319-325
• /
• 2011

This study was conducted to figure out the diagnosis basis of cooling performance depending on water amount in the refrigerant of air conditioner, which can be estimated by the temperatures and pressures along the refrigerant circulation line. A car air conditioner of SONATA III (Hyundai motor Co., Korea) was tested at maximum cooling condition at the engine speed of 1500 rpm in the room controlled at 33~$35^{\circ}C$ air temperature and 55~57% relative humidity conditionally. Measured variables were temperature differences between inlet and outlet pipe surfaces of the compressor, condenser, receive drier and evaporator; and high pressure and low pressure in the refrigerant circulation line; and temperature difference between inlet and outlet air of the cooling vent of evaporator. In this study, changes of the water amount in the refrigerant were correlated to the temperatures and pressure changes and also water amount caused poor cooling performance. As water amount increased in the refrigerant in the air conditioner, the performance of the cooling or the heat transfer became worse. Temporal variations of the surface temperature of the evaporator outlet pipe and the low-side pressure showed various patterns that could estimate the water amount. When the water amount caused bad cooling performance, the patterns of the temperature of the evaporator outlet pipe indicated irregular fluctuation greater than $5^{\circ}C$. When the diagnosis system is using just external sensors of the low-side pressure and the temperatures of inlet and outlet air of cooling vent of the evaporator, the precise pattern of bad cooling performance caused by excess water amount in the cooling line was irregular pressure fluctuation, 25 kPa under 120 kPa, and temperature, $12^{\circ}C$ and less.

• 폴리머
• /
• 제27권2호
• /
• pp.113-119
• /
• 2003

폴리(에틸렌 테레프탈레이트) (PET)의 열처리 조건들 즉, 상대 습도, 온도 그리고 시간 등에 따라 나타나는 PET의 열적 특성과 결정화 거동에 대해서 연구하였다. PET샘플에 열처리를 수행한 후 수분 함유량, 유리 전이온도($T_g$), 그리고 결정화 온도($T_{\propto}$) 등의 변화를 조사하였다. 그리고 열처리된 PET시편에 대해서 결정화를 시키고 결정화도에 따른 열변형 온도(HDT)를 측정하였다. 또한 사출 성형으로 제작된 PET샘플의 열처리 후 잔류 응력의 완화를 편광 필름을 통하여 조사하였다. 열처리 시의 상대 습도, 온도, 그리고 시간이 증가함에 따라 PET샘플 내의 수분 함유량은 최대 6000 ppm이상 까지 증가하였다. $T_g$와 $T_c$는 시편 내에 수분 함유량이 증가할수록 감소하였다. PET샘플의 결정화도는 수분의 함유량이 증가함에 따라 증가되었다. 그러나 같은 양의 수분 함량에서 결정화도는 열처리의 조건에 따라 다르게 나타났다. PET샘플 내의 잔류응력의 완화는 열처리 조건에 따라 다르게 나타났으며, PET샘플 내에 잔류 응력이 감소할수록 최대 결정화도는 증가하였다.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.32-37
• /
• 2009

In shipyard, plate forming is widely used to form the ship hull plate in various shapes. Line heating method by using a flame torch is one of the major shipbuilding processes carried out by skilled workers. Since the forming characteristics depend upon their experiences in manual forming, there are much variations between products and difficulties in communication between engineers and workers. Hence, it needs to develop an automatic forming system which can not only reduce the working time and rework costs but also improve the working environment and hull forming productivity. One of the final goals of plate forming automation is to form a target shape from the initial plate automatically. For automated plate forming, it is required to determine where and how to heat on the plate. To realize this procedure, the inverse problem should be first solved and the effect of curvature shape formed at the heating path should be investigated. In this study, the inverse problem was solved by geometrical approach using the relationship between bending angle and radius of curvature of the curved shape. In addition, experiments of two-dimensional plate forming were performed with the distance-based method considering the curved bending with curvature. The result of the formed shape agreed considerably well with the target shape.

• 대한인간공학회지
• /
• 제17권3호
• /
• pp.41-59
• /
• 1998

Thermal comfort aspect of a locally-cooled target space in warm and humid environments(typically in the rainy summer season) was studied in view of PPD index. First. theoretical analyses were conducted to examine the effect of the governing parameters(such as air temperature, relative humidity and air velocity, etc.) using a computer model. Secondly, experimental investigations were also performed in a climatic room designed to simulate corresponding thermal conditions of outdoor environments. During the tests, temporal variation of PPD was recorded as functions of climatic variables(outdoor and indoor temperatures, relative humidity and air velocity) for the given human factors(metabolic heat generation and clothing). From both theoretical and experimental investigations, air temperature and air velocity were found to be the most dominant parameters affecting PPD of the target space. Results were summarized as: 1. Relative humidity of the locally-cooled target space tends to approach that of outdoor's as the space is subjected to an ON-OFF mode of cooling, since moisture potential of the two rooms reaches an equalized state as a result of moisture diffusion. 2. It was recognized that changes in relative humidity did not show any significance in view of thermal comfort as was reported in the previous studies, while variations of both temperature and air velocity caused relatively large changes in the degree of thermal comfort. 3. In-door environment should be evaluated in terms of PPD instead of relative humidity commonly recognized as an important climatic variable particularly in warm and humid environments.