• 한국주조공학회지
• /
• 제27권2호
• /
• pp.88-94
• /
• 2007

General criteria for the risering design of steel castings and commercial codes for the flow and solidification analysis were used to design the optimized risering in V-process. Three type of specimens were chosen including thin plates and a thick disc. Sided riser installed in the front of a plate casting was effective to prevent the shrinkage defects and to increase the casting yield ratio. Exothennic sleeve and chill were also effective. It was possible to apply the general criteria for the risering design of steel castings to V-process. Temperature of a mold surface was expected to rise over $1,000^{\circ}C$ in the temperature calculation considering radiation effect of molten metal in the mold. Since weakening temperature of the vinyl used in V-process is about $70^{\circ}C$, it should be emphasized that a proper coating of the vinyl film is necessary to prevent the possibility of burning out of the vinyl by the molten metal.

• 한국정밀공학회지
• /
• 제13권3호
• /
• pp.110-122
• /
• 1996

Finite element analysis tool was developed to analyze the casting process. Generally, casting process consists of mold filling and solidification. Both filling and solidication process were simulated simultaneously to investigate the effects of process variables and to predict the defect. At filling process, thermal coupling was especially considered to investigate thermal history of material during the filling stage. And thermal condition at the final stage of filling is used as the initial conditions in a solidification process for the exact simullation of the actual casting processes. At mold filling process, Lagragian-type finite element method with automatic remeshing scheme was used to find the material flow. A perturbation method with artificial viscosity is adopted to avoid numerical instability in low viscous fluid. At solidification process, enthalpy-based finite element method was used to solove the heat transfer problem with phase change. And elastic stress analysis has been performed to predict the thermal residual stress. Through the FE analysis, solidification time, position of solidus line, liquidus line and thermal residual stress are found. Through the study, the importance of combined analysis has been emphasized. Finite element tools developed in this study will be used process design of casting process and may be basic structure for total CAE system of castings which will be constructed afterward.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.137-143
• /
• 2003

The air gap between the metal and mold, formed by shrinkage during solidification, causes surface and subsurface cracks in the continuous casting process. Molten crack on the surface might also occur due to improper heat transfer between them. In order to compensate the air gap in mold design, the thermal contraction is an essential factor. In this study, the thermal contraction and expansion behaviors were examined from the ($\alpha$ and pearlite)/${\gamma}$ to ${\gamma}$/$\delta$ transformations in continuous casting steels by the commercial dilatometer and the self- assembled dilatometer with laser distance measurement. It was found that the thermal contraction and expansion behaviors were very dependant on the phase transformation of the ${\gamma}$/$\delta$ as well as ($\alpha$ and pearlite)/${\gamma}$. The sudden volume change from $\delta$ to ${\gamma}$ which might cause cracks in the continuous casting process, was observed on cooling just below the melting temperature by the self-assembled dilatometer.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.318-324
• /
• 2017

Powder compaction technology is widely used to prepare thermal battery components. This method, however, is limited by the size, thickness, and geometry of the battery components. This limitation leads to excessive cell capacity, overweight, and higher cost of the pellets, which decreases the specific capacities and delays the activation time of thermal batteries. $FeS_2$ thin-film cathodes were fabricated by tape-casting technology and analyzed by SEM and EDS in this paper. The residual organic binder of the $FeS_2$ thin-film cathodes decreased with the temperature of the heat treatment, which improved the specific capacity because of the lower resistance. Specific capacities of the $FeS_2$ thin-film cathodes decreased because of the higher residual binder and the restrictive reaction of active materials with molten salts as the thickness increased. $FeS_2$ thin-film cathodes showed much higher specific capacity (1,212.2 As/g) than pellet cathodes (860.7 As/g) at the optimal heat-treatment temperature ($230^{\circ}C$).

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.122-128
• /
• 2000

Strip casting process is a new technology that makes a near net shape thin strip directly from molten metal. With this process, a large amount of energy and casting cost could be decreased from the abbreviation of reheating and/or hot rolling process. Ductile cast iron which has spheroidal graphite in the matrix is the most commercial and industrial material, because of its supreme strength, toughness, and wear resistance etc. But it cannot be produced to the thin strip owing to difficulty in rolling of ductile cast iron. In this study, ductile cast iron strips are produced by the twin roll strip caster, with different chemical compositions of C, Si, and Mn contents. And then heat-treated, microstructures and mechanical properties are examined. The microstructures of as-cast strip are that of white cast iron which consists of the mixture of cementite and pearlite, but the equiaxed crystal zone of the pearlite or segregation zone of cementite exists in the center region of the strip thickness, which cannot be observed in the rapidly solidified metallic mold cast specimens. This structure is supposed to be formed from the thermal distribution of strip and the rolling force. Comparing with the structures of each strips after heat treatment, increasing Si content makes smaller spheroidal graphite and more compact in the matrix, furthermore the less of Mn content makes the ferrite matrix be obtained clearer and easier. As a result of the tensile test of graphitization heat-treated strips, the yield strengths are about 250 MPa, the tensile strengths are about $430{\sim}500$ MPa, and the elongations are about $10{\sim}13%$. In the case of the strip which has the smaller and more compact spheroidal graphite in the ferrite matrix, the higher tensile strength and better drawability could be obtained.

• 한국주조공학회지
• /
• 제5권4호
• /
• pp.289-297
• /
• 1985

Thin sections in castings solidify faster than thick sections. Solidification rates increase because of an increase in heat transfer from molten meltals to molds through these solidified thin sections. The cooling fin effect in pure zinc casting was studied about the solidification time, superheat, and fin size by adopting the pourout test. The following results could be obtained from the study: (1) The fin effect could be represented by the effective cooling surface area ($A_f/S$) increased. (2) The fin effect could be obtained as functions of solidification time, superheat, and fin size.

• 한국재료학회지
• /
• 제32권12호
• /
• pp.538-544
• /
• 2022

In existing ceramic mold manufacturing processes, inorganic binder systems (Si-Na, two-component system) are applied to ensure the effective firing strength of the ceramic mold and core. These inorganic binder systems makes it possible to manufacture a ceramic mold and core with high dimensional stability and effective strength. However, as in general sand casting processes, when molten metal is injected at room temperature, there is a limit to the production of thin or complex castings due to reduced fluidity caused by the rapid cooling of the molten metal. In addition, because sodium silicate generated through the vitrification reaction of the inorganic binder is converted into a liquid phase at a temperature of 1,000 ℃. or higher, it is somewhat difficult to manufacture parts through high-temperature casting. Therefore, in this study, a high-strength ceramic mold and core test piece with effective strength at high temperature was produced by applying a Si-Na-Ti three-component inorganic binder. The starting particles were coated with binary and ternary inorganic binders and mixed with an organic binder to prepare a molded body, and then heat-treated at 1,000/1,350/1,500 ℃ to prepare a fired body. In the sample where the two-component inorganic binder was applied, the glass was liquefied at a temperature of 1,000 ℃ or higher, and the strength decreased. However, the firing strength of the ceramic mold sample containing the three-component inorganic binder was improved, and it was confirmed that it was possible to manufacture a ceramic mold and core via high temperature casting.

• 한국주조공학회지
• /
• 제28권3호
• /
• pp.119-123
• /
• 2008

Wear test on two die steels for aluminum die casting was carried out by dipping and rotating the specimens into the molten aluminum maintained $680^{\circ}C{\sim}780^{\circ}C$. The rotating speed of the specimen was $4.5rpm{\sim}20.0rpm$. Diffusion layer was formed between the die steel and molten aluminum, and became thicker with dipping time. Wear rate was not proportional with the thickness of the diffusion layer, but was closely related to the density of the diffusion layer. Wear rate was little affected by the kind of die steel and by the microstructure such as martensite, tempered martensite, and pearlite. Specimen with nitrided surface showed good wear resistance, and its wear rate was decreased with increase in the thickness of nitrided layer. While whole surface was worn in heat treated specimens, wear of nitrided specimens was proceeded by pitting partially.

• 자원리싸이클링
• /
• 제33권2호
• /
• pp.46-53
• /
• 2024

전기로 제강공정에서 연속주조 조업 완료 후 ladle에 잔존하는 슬래그의 헌열과 슬래그 중 잔존 CaO를 활용하기 위해 전기로 출강 후 ladle 상부에 슬래그를 투입하여 Ladle Furnace(LF) 공정에서의 전력과 생석회의 사용량을 저감하는 공정이 연구되어 산업현장에서 활용되고 있다. 하지만 이러한 공정은 LF 공정과 연속주조 공정상 시점이 맞지 않으면 재활용율이 낮아진다. 슬래그 재활용율을 높이기 위해서 시점이 맞지 않는 경우 ladle의 슬래그를 슬래그 포트에 미리 부은 후 재활용하는 방법에 대해서 LF 조업 영향성을 분석하였다. Ladle 용융 슬래그를 재활용 방법에 대해 열역학 프로그램 Factsage 8.3에서 FSsteel(steel database)와 FToxid(oxide database)를 활용하여 슬래그 조성에 대한 액상화율을 계산하였고, 재활용 방법에 따라 각 10heats 조업 적용을 통해 슬래그 중 탈황능과 LF 조업성에 대해서 비교하였다. 그 결과 연속주조 조업 완료 후 바로 ladle에 슬래그를 재활용하는 방법에서 전력 사용량이 0.3MWh 낮고, LF 조업시간은 1.2분 단축되었으며, 탈황율은 5.8% 높은 결과를 얻었다.

• 열처리공학회지
• /
• 제34권6호
• /
• pp.281-286
• /
• 2021

Arc ion plating (AIP), laser cladding, and nitriding are methods that can prevent mold damage or repair and create cracks and breakages on the die surface. The dissolution and soldering behavior of coated SKD61 by using arc ion plating, laser cladding, and nitriding was investigated. The structure of the coating was investigated as a function of deposition conditions by X-ray diffraction and the crystallographic orientation was determined using the texture factor. The TiAlN film deposited with AIP showed excellent corrosion resistance in the molten aluminum alloy at 680℃. In this paper, we have detailed the corrosion and mass loss phenomena associated with these steel-cast metal interactions.