• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.1
• /
• pp.24-29
• /
• 2000

This paper is experimental study of machining characteristics about martensitic heat resisting steel STR11. Machining characteristics are different according to internal quality(chemical compositions, microscopic structure and nonmetallic inclusion) mechanical properties(tensile strength value impact value and hardness) and dynamic cutting force. Following are the results : 1. In analyzing internal quality test materials have typical martensite structure and a minute needle-shaped structure. 2. Tensile strength and reduction of area and hardness are larger. But values of elongation and impact values are smaller. Fracture surface of tensile specimen is ductile. 3, Cutting force is decreasing with cutting speed increasing 4. Cutting force is increasing with feed speed increasing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.1073-1077
• /
• 1997

In this paper, we have studied internal quality including chemical compositions, microscopic structure and nonmetalic inclusion of test materials. We have analyzed machining characteristics including tensile strength value, impact value, hardness value etcs. Test materials are usd martensitic heat resisting steel, STR11 and STS420J2. The obtined results are as follows : 1. In analyzing internal quality, STR11 and STR420J2 have typical martensite structure and a minute needle-shaped structure. 2. Tensile strength and reduction of area and hardness value are large STR11 than STS420J2. But elongation impact are smaller STR11 than STS420J2. 3. Fracture surface of tensile speciman is ductile in STR11 and STS420J2.

• Korean Journal of Acupuncture
• /
• v.23 no.4
• /
• pp.85-99
• /
• 2006

Objectives : Proper acupuncture stimulation is associated with a characteristic set of sensation usually referred to as 'De-Qi'. In order to develop the appropriate sham acupuncture, various sensations to each stimulation should be considered through analysis of the profiles of acupuncture sensation. It was therefore investigated to compare the acupuncture sensation scale (ASS) of two types of sham acupuncture to that of the real acupuncture. Methods : Ninety-four participants (mean age 26.4, range 26-49) were asked to complete five point-Likert scale ASS developed by Vincent et al. after real or two-kinds of sham acupuncture stimulation: blunted tip sham acupuncture (BT) and round tip sham acupuncture (RT). Needling was done at LI4 acupoint on non-dominant hand and stimulated for 30 seconds with real or two-kinds of sham needle. Finger withdrawal latency (FWL) of each group was also measured to evaluate the pain sensitivity to noxious heat stimuli. Results : BT acupuncture significantly less produced penetrating, numb, intense, hurting, pulling, shock, tingling, throbbing sensation than real acupuncture stimulation. RT acupuncture significantly less produced penetrating, burning, electric, numb, intense, hurting, pulling, aching, shasharp, shock, stinging, tingling, throbbing sensation than real acupuncture. Each group did not demonstrate the differences of pain sensitivity to noxious stimuli. Conclusions : These results indicated that types of tip of acupuncture produced different kinds of acupuncture sensation. Our finding provides a general information of sensations to two kinds of sham acupuncture for development of ideal placebo sham needle.

• Korean Journal of Acupuncture
• /
• v.38 no.4
• /
• pp.209-221
• /
• 2021

Objectives : The aim of this study was to compare and analyze studies related to fire acupuncture (FA) published in South and North Korea. Methods : FA studies published in South Korea were searched through domestic and overseas databases (KISS, RISS, OASIS, and EMBASE). For North Korean studies, databases from the Information Center on North Korea and Korea Institute of Science and Technology Information were used. Among the searched literatures, clinical studies using FA as a treatment intervention were selected (i.e., randomized controlled trials, and case reports). Finally, information such as the disease for which FA was used, the characteristics of FA, and details of treatment methods for FA were extracted from the screened literatures and the results of South and North Korean studies were compared and analyzed. Results : This review included 28 South Korean studies and 9 North Korean studies. All studies in South Korea, except for the three articles that used traditional FA treatment, applied "warm needling"-like acupuncture (WA) in the form of heating the handle of the needle after inserting the needle into the skin, and most studies were conducted on diseases of the musculoskeletal system. Whereas in the North Korean studies, FA was applied to various diseases such as trigeminal neuralgia, skin diseases, and gastrointestinal diseases, and standardized FA tools were used. Conclusions : Studies on traditional FA treatment have rarely been reported in South Korea. The amount of information described in the FA studies in North Korea was limited. In this review, the characteristics of FA treatment tools in South and North Korean studies were mainly analyzed. In the future, FA studies from more diverse perspectives are needed.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.4
• /
• pp.191-197
• /
• 2013

The one of the cathode material, $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$, was synthesized by the precursor, $Ni_{0.5}Co_{0.2}Mn_{0.3}(OH)_2$, from the co-precipitation method and the morphologies of the primary particle of precursors were flake and needle-shape by controlling the precipitation parameters. Identical powder properties, such as particle size, tap density, chemical composition, were obtained by same process of lithiation and heat-treatment. The relation between electrochemical performances of $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ and the primary particle morphology of precursors was analyzed by SEM, XRD and EELS. In the $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ cathode from the needle-shape precursor, the primary particle size was smaller than that from flake-shape precursor and high Li concentration at grain edge comparing grain center. The cycle and rate performances of the cathode from needle-shape precursor shows superior to those from flake-shape precursor, which might be attributed to low charge-transfer resistance by impedance measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.495-497
• /
• 1999

In order to determine what influences the interfacial breakdown in EPDM/XLPE laminates, We made the breakdown test ceil and this was pressure controllable breakdown test cell. We make the needle electrode (tip radius: about 10 micrometer) using electrochemical method. We studied the interfacial silicone oil was higher than that with silicone grease. As a function of heat treatment time in a vacuum, interfacial breakdown strength increased much in XLPE/EPDM laminates pasted with silicone grease but increased a little in that with silicone oil.

• Radiation Oncology Journal
• /
• v.9 no.1
• /
• pp.27-35
• /
• 1991

An interstitial radiofrequency needle electrode system was constructed for interstitial heating of brain tissue. Radiofrequency electrodes with Thermotron RF 8 were tested in an agar phantom and in a normal canine brain to determine how variations in physical factors affected temperature distributions. Temperature distributions were checked after heating with 1 mm diameter needle electrode implants on the corners of 1 and 2 cm squares in a phantom and plot isotherms for various electrodes arrangement. We observed that the 1 cm square array would heat a volume with a 1.25 cm radius circular field cross section to therapeutic temperatures ($90\%$ relative SAR using Tm) and the 2 cm square array with a 1.75 cm radius rectangular field with central inhomogeneity. With 2 cm long electrode implants, we observed that the 1 cm square array would heat a 3 cm long sagittal section to therapeutic temperature ($90\%$ relative SAR using Tm). We found that radiofrequency electrodes could be selected to match the length of the heating area without affecting its performance. The histopathological changes associated with RF heating of normal canine brains have been correlated with thermal distributions. RF needle electrode heating was applied for 50min to generate tissue temperatures of $43^{\circ}C$. We obtained a quarter of the heated tissue material immediately after heating and sacrificed at intervals from $7\sim30$days. The acute stage (immediately after heating) was demonstrated by liquefactive necrosis, pyknosis of neuronal element in the gray matter and by some polymer-phonuclear leukocytes infiltration. The appearance of lipid-laden macrophages surrounding the area of liquefaction necrosis was demonstrated in all three sacrificed dogs. Mild gliosis occurring around the necrosis was demonstrated in the last sacrificed (Days 30) canine brain.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.2
• /
• pp.101-112
• /
• 1995

A study was made to examine the effects of heat-treatment on the microstructures of Cu-bearing HSLA steels. The details of microstructures were studied by using optical microscopy(OM), transmission electron microscopy(TEM) and hardness test. The as-rolled microstructure of HSLA-A consists of ferrite (${\alpha}$) whereas that of HSLA-B consists of needle-shaped phase. The difference in microstructure can be ascribed to the different amount of Ni, Mn, Mo, Cu which affect the hardenability. The austenite grain size is very small up to $1000^{\circ}C$ owing to the Nb-precipitates. As the austenitizing temperature increases above $1000^{\circ}C$, the austenite grain grows rapidly. There are two hardness peaks in the hardness versus temperature curve, at $500^{\circ}C$ and at $675^{\circ}C$ (HSLA-A), $725^{\circ}C$ (HSLA-B). The peak at $500^{\circ}C$ result from the formation of Cu-precipitates and second hardness peak is created due to the formation of M-A constituents. The hardriess decrease in HSLA-B steel with ageing temperature is small because of the higher amounts of Cu than HSLA-A steel. The fine, round ${\varepsilon}$-Cu precipitates grow with ageing temperature and finally transform into rod shape.

• Korean Journal of Metals and Materials
• /
• v.49 no.6
• /
• pp.448-453
• /
• 2011

Pre-aging heat treatment after solution heat treatment (SHT) of Al-0.4 wt%Mg-1.2 wt%Si-0.1 wt%Mn alloy sheets for auto-bodies was carried out to investigate the effect of pre-aging and its conditions on the bake-hardening response. Mechanical properties were evaluated by a tensile and Vickers hardness test. Microstructural observation was also performed using a transmission electron microscope (TEM). It was revealed that pre-aging treatments play a great role in the bake-hardening response. In addition, it was found that the sphere-shaped nanosized clusters that can directly transit to the needle-shaped ${\beta}$" phase during the paint-bake process, not being dissolved into the matrix, are formed at 343 K. The result, reveals that the dominant factor of the bake-hardening response is the pre-aging temperature rather than the pre-aging time.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.3
• /
• pp.150-158
• /
• 2022

The effects of scandium addition on the Al-6Si-2Cu Alloy were investigated. The Al-6Si-2Cu-Sc alloy was prepared by gravity die casting process. In this study, scandium was added at 0.2 wt%, 0.4 wt%, 0.8 wt%, and 1.0 wt%. The microstructure of Al-6Si-2Cu-Sc alloy was investigated using Optical Microscope, Field Emission Scanning Electron Microscope, Electron Back Scatter Diffraction, and Transmission Electron microscope. The microstructure of Al-6Si-2Cu alloy with scandium added changed from dendrite structure to equiaxed crystal structure in specimens of 0.4 wt% Sc or more, and coarse needle-shape eutectic Si and β-Al₅FeSi phases were segmented and refined. The nanosized Al₃Sc intermetallic compound was observed to be uniformly distributed in the modified Al matrix.