• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.331-337
• /
• 2001

A numerical simulation of the temperature rise for sliding surface in dry contact is based on Jaegers formula combined with a calculated heat input. A gear tooth temperature analysis was performed. The pressure distribution has the Hertzian pressure distribution on the heat source. The heat partition factor is calculated along ling of action. A Temperature distribution of tooth surface is calculated about before and after profile modification. A Temperature of addendum and deddendum in modified gear have reduced.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1394-1402
• /
• 1996

The Silica gel with the density of 0.2g/cm3 and porosity of 90% was synthesized. The silica wet gel was dried and heat-treated under the ambient pressure after modification of the wet gel surface by TMCS. Specific surface area total pore volume and mean pore radius of dried gel were all increased with increasing heat treatment temperature and confirmed about 1400m2/g, 4.5cc/g and 8 nm respectively after heat treatment above 25$0^{\circ}C$. But the pore size distribution of dried gel was in the range of 1-100nm and was almost indepen-dent of temperature. As the result of external shape pore characteristics and microstructure of gel using SEM similar properties were observed between the silica gel synthesized in this study and the silica aerogel through the super critical drying.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.6
• /
• pp.291-295
• /
• 2013

Surface chemical modification via air and hydrogen heat treatment was found to relieve the aggregation of nanodiamond (ND) seed particles and lead to a significantly enhanced nucleation density for ultrananocrystalline diamond (UNCD) film growth. After heat treatment in air and hydrogen, modification of surface functionalities and increase in the zeta potential were observed. Mean size of the ND aggregates was also dramatically reduced from ${\sim}2{\mu}m$ to ~55 nm. Si surface seeded with ND particles heat-treated at $600^{\circ}C$ in hydrogen produced a much higher nucleation density of ${\sim}2.7{\times}10^{11}cm^{-2}$ compared to untreated ND seeds.

• Korean Journal of Chemical Engineering
• /
• v.35 no.12
• /
• pp.2480-2486
• /
• 2018

Mesoporous $TiO_2$ microspheres were prepared by spray pyrolysis for photocatalysis. Post modification of $TiO_2$ by heat treatment was performed to optimize its photocatalytic performance. First, spherical $TiO_2$ particles with mesoporous structure were synthesized at pyrolysis temperatures of 500, 600, and $700^{\circ}C$. After characterization by XRD, SEM, and $N_2$ adsorption, a sample prepared at $500^{\circ}C$ was found to possess desirable properties for photocatalytic performance through post-modification. In methylene blue degradation, mesoporous $TiO_2$ microspheres synthesized at $500^{\circ}C$ outperformed other microspheres. Furthermore, samples obtained by spray pyrolysis at $500^{\circ}C$ were calcined at various temperatures as a post-modification process. The sample calcined at $350^{\circ}C$ showed improved photocatalytic activity due to optimal anatase crystallinity and surface area.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.3
• /
• pp.503-510
• /
• 2010

The quick variation of the canister wall temperature causes the modification of the shape of canister wall. This paper is the possibility of adoption and the error analysis about the transient heat flux method. The commercial code(Fluent Ver6.2.16) was employed for the calculation of surface temperature in the case of steady and unsteady heat flux condition. Based the surface temperature variation and surface material property, transient heat flux method can calculate the surface heat flux. In the case of steady heat flux condition, the error is about 2%, and in the case of unsteady heat flux condition, the error is about 3.6%. With the unsteady heat flux condition, the time which reach the maximum surface heat flux is almost same between the numerical analysis and transient heat flux method.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.225.2-225
• /
• 2001

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.113.2-113.2
• /
• 2000

• Membrane and Water Treatment
• /
• v.15 no.1
• /
• pp.21-29
• /
• 2024

1H,1H,2H,2H-perfluorodecytriethoxysilane (C₁₆H₁₉F₁₇O₃Si) be successfully applied to the hydrophobic modification of Al₂O₃ tubular ceramic membrane. Taking the concentration of modification solution, modification time, and modification temperature as factors, orthogonal experiments were designed to study the hydrophobicity of the composite membranes. The experiments showed that the modification time had the greatest impact on the experimental results, followed by the modification temperature, and the modification solution concentration had the smallest impact. Concentration of the modified solution 0.012 mol·L^-1, modification temperature 30 ℃ and modification time 24 h were considered optimal hydrophobic modification conditions. And the pure water flux reached 274.80 kg·m^-2·h^-1 at 0.1MPa before hydrophobic modification, whereas the modified membrane completely blocked liquid water permeation at pressures less than 0.1MPa. Air gap membrane distillation experiments were conducted for NaCl (2wt%) solution, and the maximum flux reached 4.20 kg·m^-2·h^-1, while the retention rate remained above 99.8%. Given the scarcity of freshwater resources in coastal areas, the article proposed a system for seawater desalination using air conditioning waste heat, and conducted preliminary research on its freshwater production performance using Aspen Plus. Finally, the proposed system achieved a freshwater production capacity of 0.61 kg·m^-2·h^-1.

• Journal of Korea Foundry Society
• /
• v.38 no.1
• /
• pp.1-8
• /
• 2018

In this study, we focused on the correlation between the solidification structure, heat treatment and mechanical properties of the A356 alloy according to the conditions of Sr modification. The microstructural evolution of the eutectic Si and ${\alpha}-Al$ phase in the A356 alloy castings depending on the amount of Sr were investigated during solid solution heat treatment using an optical microscope, a scanning electron microscope and an image analyzer. In addition, tensile tests on the heat treated materials examined the relationship between the microstructure and the fracture surface. The as-cast A356 alloys under 40 ppm Sr showed an undermodified microstructure, but that of the added 60-80 ppm Sr had well modified structure of fine fibrous silicon. After solid solution treatment, the microstructure of the undermodified A356 alloy exhibited a partially spheroidized morphology, but the remainder showed the fragmentation of fibrous shaped silicon. The spheroidization of the eutectic silicon in the modified A356 alloys was completed during heat treatment, which was very effective in increasing the elongation. This is supported by the fracture surface in the tensile test.

• Transactions of Materials Processing
• /
• v.15 no.9 s.90
• /
• pp.679-685
• /
• 2006

New method for evaluation of heat transfer coefficient is proposed. In general, many researchers have been studied about inverse problem in order to calculate the heat transfer coefficient on three-dimensional heat conduction problem. But they can get the time-dependent heat transfer coefficient only through inverse problem. In order to acquire temperature-dependent heat transfer coefficient, it requires much time for numerous repetitive calculation and inconvenient manual modification. In order to solve these problems, we are using the SQP(Sequential Quadratic Programming) as an optimization algorithm. When the temperature history is given by experiment, the optimization algorithm can evaluate the temperature-dependent heat transfer coefficient with automatic repetitive calculation until difference between calculated temperature history and experimental ones is minimized. Finally, temperature-dependent heat transfer coefficient evaluated by developed program can used on various heat transfer problem.