• 한국건설순환자원학회논문집
• /
• 제6권4호
• /
• pp.103-111
• /
• 2012

압축강도 50 MPa이상의 압출성형 시멘트 패널은 고온고압 증기양생으로 생산된다. 고온고압 증기양생에서 요구 강도를 얻기 위해서는 시멘트에 포함되어 있는 CaO와의 반응에 필요한 적정량의 $SiO_2$를 공급하는 것이 관건이다. $SiO_2$의 공급원으로 가장 널리 사용되는 원료는 규석분인데, 이는 환경파괴를 전제로 하기 때문에 친환경적인 제품 생산을 위하여 본 연구에서는 규석분을 대신하여 폐석분을 활용한 시멘트 2차 제품을 생산하고 이에 대한 압출성과 물리적인 특성비교를 실시하였다. 이를 위하여 화성 석산에서 채취한 폐석분을 건조 파쇄한 후 이를 규석분 사용량의 최대 50%까지 치환하여 압출성 및 물리적 특성 실험을 수행하였다. 실험결과 평균 입경은 폐석분과 규석분의 크기가 유사하였으나 물리적 특성은 규석분을 폐석분으로 단순 치환하였을 경우, 대부분 낮게 발현되었다. 따라서 폐석분을 활용할 경우 수화활성을 위한 첨가제 등의 활용이 필요할 것으로 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권6호
• /
• pp.163-170
• /
• 2012

한중콘크리트 공사에 적용을 검토할 수 있는 초속경 콘크리트는 초기 급속한 발열반응을 통해 동해를 입기 전에 소요의 강도를 확보할 수 있을 것이며, 열 보상을 통해 시공환경이 유지될 경우 강도발현에 필요한 시간을 단축할 수 있는 장점이 있다. 일반 콘크리트는 영하의 기온에서 타설할 경우 양호한 경화를 얻을 수 없으며, 저온에서 동해를 방지하고 경화성을 확보하기 위하여 내한방동제를 첨가하여 사용하고 있다. 그러나, 내한방동제의 대부분은 염화물을 주성분으로 하고 이를 다량으로 사용할 경우, 콘크리트의 동결을 방지하고 시멘트의 수화반응을 촉진시켜 응결시간을 단축하고 초기강도 증진을 유도하는 효과가 있는 반면, 장기재령에서 강도발현이 문제가 되고, 경제성이 떨어진다는 단점이 있다. 최근 연구되고 있는 마그네시아 인산염 복합체는 초속경성이 있고 저온에서도 수화반응이 가능한 것으로 보고되고 있어 새로운 한중공사 및 극한지용 건설재료로 사용할 수 있을 것으로 판단된다. 따라서, 본 연구에서는 한중공사 및 극한지에서 사용이 가능한 건설재료의 개발을 위한 사전 연구의 일환으로서, 마그네시아 인산염 복합체를 활용한 모르타르에 대해 온도의 영향을 고려한 재료 물성 평가를 실시하고 적정 배합을 제안하고자 한다.

• 한국건축시공학회지
• /
• 제5권1호
• /
• pp.81-88
• /
• 2005

As a part of efforts for conformity of demand to high quality of concrete and for solution of economic problem, blast-furnace slag has been utilized by means of cement replacement. With utilization of blast-furnace slag, superior performance can be ensured, environmental pollution can be prevented and economical advantage can be obtained. But blast-furnace slag has a lot of disadvantages like retardation of strength manifestation etc. in field construction, so properties examination of concrete using blast-furnace slag instead of cement is necessary. For upper necessity, it is planed that basic data for utilization and performance management of blast-furnace slag by means of cement replacement is presented with experimental comparison and investigation of engineering properties of concrete according to the replacement ratio and fineness of blast-furnace slag.

• 한국건축시공학회지
• /
• 제5권3호
• /
• pp.101-107
• /
• 2005

This paper reports the contribution of Shrinkage reducing admixture(SRA) to the physical properties and drying shrinkage of concrete. Dosage of SRA is varied with. For the properties of fresh concrete, an increase in SRA dosage results in a decrease in fluidity and air content, while setting time is accelerated. For the properties of hardened concrete, the incorporation of mineral admixture leads to a decrease in compressive strength at early age, whereas after 28 days, the incorporation of fly ash(FA) and blast furnace slag(BS) has greater compressive strength than conventional concrete without admixture. The use of SRA results in a decrease in compressive strength. The incorporation of SRA with every $1\%$ increase causes the decrease of compressive strength by as much as $3\~6\%$. For drying shrinkage properties, the incorporation of FA and BS reduces drying shrinkage slightly. The use of SRA also decreases drying shrinkage. Every $1\%$ of increase in SRA dosage can reduce drying shrinkage by as much as $10\~15\%$

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.85-90
• /
• 2003

Although wear resistance of material improves with increasing its hardness, it is known that the wear resistance of steel is varied with hardness of counter material. In this context, wear properties of steel must be depended on the difference of hardness between the testpiece and the counter material. In this study, using the pin-on-disc type wear machine, annealed carbon steels were tested against ahoy tool steels with various levels of hardness. Then the changes of wear properties of carbon steel according to the hardness of counter material were investigated and the morphology of worn surface after test were evaluated. The results indicate that if there are no remarkable difference of hardness between them, wear resistance of carbon steel in running-in wear decreases with increasing the hardness of counter material. However, its wear properties at the range of high sliding speed have no relation with hardness of counter material. It is clear that wear properties is influenced by the formation of oxide of steel on their worn surface during wear.

• Computers and Concrete
• /
• 제20권4호
• /
• pp.449-459
• /
• 2017

Fresh and hardened behaviors of a new hybrid fiber (steel fiber, polyvinyl alcohol fiber and calcium carbonate whisker) reinforced cementitious composites (HyFRCC) with admixtures (fly ash, silica fume and water reducer) have been studied. Within the limitations of the equipment and testing program, it is illustrated that the rheological properties of the new HyFRCC conform to the modified Bingham model. The relations between flow spread and yield stress as well as flow rate and plastic viscosity both conform well with negative exponent correlation, justifying that slump flow and flow rate test can be applied to replace the other two as simple rheology measurement and control method in jobsite. In addition, for the new HyFRCC with fly ash and water reducer, the mathematical model between the rheological and mechanical properties conform well with the quadratic function, and these quadratic function curves are always concave upward. Based on mathematical analysis, an optimal range of rheology/ flowability can be identified to achieve ideal mechanical properties. In addition, this optimization method can be extended to PVA fiber reinforced cement-based composites.

• 한국건축시공학회지
• /
• 제12권1호
• /
• pp.73-86
• /
• 2012

In this research, the possible applicability of mixture blended with natural, crushed, and recycled fine aggregate are discussed. The fresh and hardened properties of mortar using blended fine aggregates are monitored depending on various blending ratio of fine aggregates. Newly developed ternary diagram was also utilized for better interpretation of the data. It was found that air content increased and unit weight decreased as recycled fine aggregate content increased. With moisture type processing of recycled fine aggregate, the mortar flow was not negatively affected by increase in the recycled fine aggregate content. The ternary diagram is found to be an effective graphical presentation tool that can be used for the quality evaluation of mortar using blended fine aggregate.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.27-32
• /
• 2002

In this research influences of type and concentration of alkali activator and curing condition on the hydration, and properties of alkali activated blast furnace slag(AAS) concrete were investigated. Sodium carbonate and sulfate were used as alkali activators and their concentration were 4~10 weight percent with Na$_2$O equivalent to binder. The curing conditions were standard curing using 23$^{\circ}C$ water and activated curing chamber at $65^{\circ}C$. Results show that in case of sodium carbonate addition high early strengths were gained by activation of early hydration, but later strength gained was slight. On the other side sodium sulfate strengths were continuously increased with adding amount and ages. Steam curing activated early hydration so that early strengths were improved but later strengths were similar to standard curing. The strength reduction of AAS mortar with sodium sulfate was less than OPC mortar in 5% sulfuric acid solution so that AAS concrete can be useful for acid-resistance concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.217-222
• /
• 2002

The purposes of this study are to investigate the material characteristics and strength properties of concrete mixed with waste incinerated bottom ash(BA), and to evaluate the leaching of environmentally harmful heavy metals from the bottom ash itself and from hardened concrete mixed with bottom ash. For this purpose, two reference mixes with W/C ratios of 0.45 and 0.55 were used, and the replacement proportion of BA was varied with the ratios of 0%, 30%, 50%, 70%, and 100% by volume of fine aggregate in the reference mixes. The variation of compressive and splitting tensile strength, workability and unit weight of concrete were considered. Test results showed that the strengths, workability and unit weight decreased with increase in proportion of BA replaced. Leaching test results showed that there would be no environmentally harmful problem from using BA as the substitutes of fine aggregates in concrete.

• 산업기술연구
• /
• 제22권A호
• /
• pp.161-168
• /
• 2002

Latex modified concrete is governed by both cement hydration and polymer film formation processes in its binder phase. Such the reactions are expected to improve the polymer-cement co-matrixes themselves and the bond between the cement hydrates and aggregates, and to improve the properties of hardened latex-modified concrete. The purpose of this study was to study the strength and chemical resistance of Rapid-setting latex modified concrete(RSLMC) with the main experimental variables such as latex content(0, 5, 10, 15, 20%) and water-cement ratio(36, 38, 40%) at latex content 15%. Water absorption test was earned out to estimate water permeability resistance. Chemical resistance test was carried out to measure the weight change and to observe the appearance of RSLMC immersion in hydrochloric acid, sulfuric acid, and calcium choloride.