• 방사성폐기물학회지
• /
• 제14권1호
• /
• pp.57-61
• /
• 2016

The Tomographic Gamma Scan (TGS) technique partitions radioactive waste drums into $10{\times}10{\times}16$ voxels and assays both the density and concentration of radioactivity for each voxel thus providing for improved accuracy, when compared to the traditional Non-Destructive Assay(NDA) techniques. It could decrease the degree of precision measurement since there is a trade-off between spatial resolution and precision. This latter drawback is compensated by expanding the Region of Interest (ROI) that differentiates the full energy peaks, which, in turn, results in an optimized degree of precision. The enlarged ROI, however, increases the probability of interference among those nuclides that emit energies in the adjacent spectrum. This study has identified the cause of such interference for the reference nuclide of the TGS technique, $^{137}Cs$ (661.66 keV, half-life 30.5 years), to be $^{110m}Ag$ (657.75 keV, half-life 249.76 days). A new calibration method of determining the optimized ROI was developed, and its effectiveness in accurately characterizing $^{137}Cs$ and eliminating the interference was further ascertained.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.663-667
• /
• 2000

The spindle unit is core parts in high precision machine tools. Diverse static and dynamic charateristics of spindle unit are needed for special purpose of machine tools. Specially, high damping ability may be very useful to high precision and high speed spindle unit. But commercial bearing system has very low damping value and high stiffness. In this paper, the combined bearing system with ball-hydrostatic bearing is suggested for high damping spindle unit. The suggested bearing system has 30% damping ability more than general ball bearing's. The average rotational accuracy of spindle with combined bearing in working speed is 24% better than with ball bearing. The unbalance rotating experiment in spindle show that rotating error with combined bearing is only half value of with ball bearing.

• International Journal of Heart Failure
• /
• 제6권2호
• /
• pp.47-55
• /
• 2024

Heart failure with mid-range ejection fraction (HFmrEF) and preserved ejection fraction (HFpEF) represent over half of heart failure cases but lack proven effective therapies beyond sodium-glucose cotransporter 2 inhibitor and diuretics. HFmrEF and HFpEF are heterogeneous conditions requiring precision phenotyping to enable tailored therapies. This review covers concepts on precision medicine approaches for HFmrEF and HFpEF. Areas discussed include HFmrEF mechanisms, anti-inflammatory and antifibrotic treatments for obesity-related HFpEF, If inhibition for HFpEF with atrial fibrillation, and mineralocorticoid receptor antagonism for chronic kidney disease-HFpEF. Incorporating precision phenotyping and matched interventions in HFmrEF and HFpEF trials will further advance therapy compared to blanket approaches.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.244-248
• /
• 2001

A solid modeller was developed in this paper. Representation scheme of modelling is nonmanifold B-rep. While many B-rep modelers use edges as basic element of modelling, this modeller is triangle-based. New modelling element, split triangle that is composed of 3 pure half-edges and has no information about the adjoining triangles, was defined to enlarge the range of representation. Corresponding algorithms for Boolean set operations were also developed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.513-517
• /
• 1995

In this paper, a relation of matrix Q in cost function to distances between the closed-loop and open-loop poles of a multi input controllable systems is studied. Futhmore, the state feedback gain with exact desired eigenvalues in the LQR is computed. The proposed scheme is applied to designing automotive active suspension control system for a half-car model and its performance is compared with the existing LQR control system design methodology.

• 오토저널
• /
• 제11권3호
• /
• pp.8-12
• /
• 1989

The development of a microprocessor-controlled centreless grinding station has opened the way for the production of automobile camshafts-from raw casting to precision-finished part-as a fully automated operation. This results in manufacture to finer tolerances, with part-to-part consistency and a floor-to-floor time of half that needed for alternative production methods. Shafts with a grinding length of up to 700 mm can be processed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.833-834
• /
• 2009

• 한국정밀공학회지
• /
• 제6권3호
• /
• pp.46-59
• /
• 1989

The purpose of test fixture is to mechanically couple energy from a shaker into a test specimen. And then it is necessary to design a fixture of shich the fundamental natural frequency is over than one half times as high as the highest frequency of interest. But the dynamic behavior of vibration test fixture is usually different from, often far different from, what has been calculated. In this paper, the optimal dimensionless frequency parameter, ${lambda}$'s, are calculated from the test results of a various and complex shaped fixtures.

• 한국정밀공학회지
• /
• 제10권1호
• /
• pp.89-99
• /
• 1993

A solid modeller was developed in this paper. Representation scheme of modelling is nonmanifold B-rep. While namy B-rep modellers use edges as basic element of modelling, this modeller is triangle-based. New modelling element, split triangle that is composed of 3 pure half-edges and has no information about the adjoining triangles, was defined to enlarge the range of representation. Corresponding algorithms for Boolean set operations were also developed.

• 소성∙가공
• /
• 제21권3호
• /
• pp.202-206
• /
• 2012

Marking is a process that engraves letters or a pattern onto the surface of sheet metal. During marking, it is important to set the proper working conditions for clarity of the letters. In this study a simple case for forming circular protrusions by half-piercing and embossing was initially attempted to determine the working conditions which gave good results with respect to shape accuracy. Corner-radius and flatness of circular protrusions made under several experimental conditions were measured and compared. It is shown that the precision of protrusions by half-piercing is superior to that of embossing, and the clearance between punch and die exerts a strong influence on the shape accuracy rather than the penetration percentage into the thickness of the sheet metal. The marking dies for "SNUT" letters, as an example, by applying the above results were manufactured with four different clearances. The working variables for the experiment were clearance and marking depth. For the very shallow depth of 0.1mm the letters were not clearly read. Letters marked under other conditions were easily distinguished with increasing marking depth. It was confirmed that the half-piercing technique with proper values of the working variables gives good quality for the marking of sheet metal.