• Journal of the Korea institute for structural maintenance and inspection
• /
• v.2 no.2
• /
• pp.170-176
• /
• 1998

The team mixed PbO, $ZrO_2$, $TiO_2$, $Nb_2O_5$ and $MnCO_3$, to make $Pb[(Zr_{0.54}\;Ti_{0.46})\;Nb_{0.005}]O_3+4%MnCO_3$. The electroded PZT ceramics were poled by 3 kV/mm at $110^{\circ}C$ for 600 s. We assembled the 0.4mm thick PZT slices into ultrasonic transducers. Central frequency of the probe is 5 MHz, which is proper to the thickness gauge for steel pipes and for flaw detector. The probe can detect a disk shape defect of 1mm diameter at 15cm deep in steel block. The new probe's Fresnel zone that the ultrasonic beam do not broaden is 13mm. Over the Fresnel zone, the ultrasonic beam spreads. Half of the beam spread angle of the probe is $4.3^{\circ}-4.6^{\circ}$. This probe can be used for the ultrasonic transducers for non-destructive testing of steel bridges.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.285-293
• /
• 2011

This paper proposes two SRM driving systems using a variable dc-link voltage controlled by a single-phase inverter. Two SRM converter topologies of a half bridge type and a full bridge type are proposed according to the power circuits of an inverter. The phase current can be controlled by means of a PWM controller at the inverter, and the turn-on/off angle at the phase switches can be controlled by a position sensor at the converter in the drive system. The inverter acts as a peak-current limiter if the transient current exceeds its maximum value. SRMs using the proposed topologies maintain high efficiency due to energy regeneration after the turn-off of power switches. The operational modes of the proposed topologies are verified by simulation and experimental results.

• Applied Science and Convergence Technology
• /
• v.26 no.6
• /
• pp.189-194
• /
• 2017

Effects of gas injection scheme and rf driving current configuration in a dual turn inductively coupled plasma (ICP) system were analyzed by 3D numerical simulation using CFD-ACE+. Injected gases from a tunable gas nozzle system (TGN) having 12 horizontal and 12 vertical nozzles showed different paths to the pumping surface. The maximum velocity from the nozzle reached Mach 2.2 with 2.2 Pa of Ar. More than half of the injected gases from the right side of the TGN were found to go to the pump without touching the wafer surface by massless particle tracing method. Gases from the vertical nozzle with 45 degree slanted angle soared up to the hottest region beneath the ceramic lid between the inner and the outer rf turn of the antenna. Under reversed driving current configuration, the highest rf power absorption region were separated into the two inner islands and the four peaked donut region.

• Journal of the Korean Mathematical Society
• /
• v.49 no.4
• /
• pp.671-686
• /
• 2012

This paper mainly deals with the tilted Carath$\acute{e}$odory class by angle ${\lambda}$ ${\in}$ ($-{\pi}/2$, ${\pi}/2$), denoted by $P{\lambda}$) an element of which maps the unit disc into the tilted right half-plane {<${\omega}$ : Re $e^{i{\lambda}}{\omega}$ > 0}. Firstly we will characterize $P{\lambda}$ from different aspects, for example by subordination and convolution. Then various estimates of functionals over $P{\lambda}$ are deduced by considering these over the extreme points of $P{\lambda}$ or the knowledge of functional analysis. Finally some subsets of analytic functions related to $P{\lambda}$ including close-to-convex functions with argument ${\lambda}$, ${\lambda}$-spirallike functions and analytic functions whose derivative is in $P{\lambda}$ are also considered as applications.

• Journal of Korea Multimedia Society
• /
• v.14 no.6
• /
• pp.752-758
• /
• 2011

In this paper, we perform a research on a message delivery link based on visible light communication using illumination light-emitting diodes (LEDs) for car-to-car communications and the link transmission success probability is analyzed for the link. The message delivery system is modeled and the signal-to-noise ratio is calculated from the received optical power. Then, the link transmission probability is estimated from the calculated bit error rates (BERs). The message delivery system has optical links from an LED transmitter near the rear lamp of a car ahead to a receiver near the headlamp of a car behind, whose positions are assumed to follow the normal Gaussian distribution. The link transmission success probability is calculated considering the physical characteristics of the optical link. The car positions are generated according to the normal distribution and the bit error rates are calculated for all links. The link transmission success probability is defined. For the unoptimized optical car-to-car message delivery links, it is shown that the link transmission success probability is larger than 0.9 with the transmitted optical power of 400 mW and the semi-angle at half power of 30 degree.

• Journal of the Korean Chemical Society
• /
• v.36 no.6
• /
• pp.812-817
• /
• 1992

Fluorometholone $(C_{22}H_{29}FO_4)$, M.W. = 376.5, monoclinic, $P2_1$, a = 6.410(4), b = 13.431(3), c = 10.996(3)$\AA$, $\beta$ = 92.81$(3)^{\circ}$, Z = 2, F(000) = 404, T = 292K, $\lambda$(Mo-$K_\alpha$) = 0.7107$\AA$, $\mu$ = 0.57$cm^{-1}$, $D_c$ = 1.32 $g/cm^3$, $D_m$ = 1.31 $g/cm^3$ and final R = 0.032 for 1769 observed reflections. All bond lengths and angles are within normal limits. Ring A is almost planar, B ring has a highly symmetrical chair conformation and C ring is in a distorted chair conformation. Ring D is in a intermediate conformation between 13$\alpha$-14$\beta$-half-chair and 13$\alpha$-envelope. Torsion angle C(16)-C(17)-C(20)-O(20) of $-7.9^{\circ}$ is a lower value than those of $-31.9^{\circ}$ and $-16.5^{\circ}$ for 9-fluoro-6-methylprednisolone I and II respectively.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.41-48
• /
• 2008

This paper deals with the characteristics of earth pressure to the debris-fall prevention walls which usually are installed in front of steep slope. Such walls have narrow backfill width where the active soil wedge can not be developed fully. The earth pressure to such walls ue affected by the movement of wall and arching effects due to the friction developing on the surface of adjacent ground slope and wall and therefore cannot be analyzed and calculated reliably. The study is carried out through laboratory model tests using centrifuge test. Test results reveal that the earth pressure to the debris-fall prevention wall depends largely on the inclination angle of the ground slope and the wall movement. The earth pressure reduction due to wall movement was observed at the upper half of wall, while the arching effect was significant at the lower half especially in the case of steep ground slope. It can be said that from the result of this study in the design of a debris-fall prevention wall the earth pressure should be determined considering the inclination of ground slope and the condition of wall movement during and after construction.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.3
• /
• pp.269-279
• /
• 2011

This study was analyzed the characteristics on the stability of posture while conducting a through two and half rotation technic of pench$\acute{e}$ in rhythmic gymnastics. Two rhythmical gymnastics player(LKH and SSJ) who is a member of the national team were selected, and for obtain the kinematic and kinetic variables were used a ProReflex MCU 240 infrared camera(Qualisys, Sweden) and a Type9286A force platform(Kistler, Switzerland). The mechanical factors were computed by using Visual3D program and Matlab R2009a. During the landing and rotation phase the results showed following characteristics; 1) In medial-lateral and horizontal displacement of the support foot, LKH showed smaller movement than SSJ, but SSJ showed smaller movement than LKH in swing foot. LKH showed bigger movement in medial-lateral axis of COP and vertical axis of COG, but SSJ showed bigger movement in horizontal axis of COP and medial-lateral axis of COG. 2) SSJ showed bigger maximum horizontal and vertical velocity at P1 and P2 than LKH. 3) In the inclination angle of COP and COG, SSJ showed smaller change than LKH, but within medial-lateral tilt of the shoulder, LKH performed rotation motion in horizontal position than SSJ. There was no differences in each force components during rotation, but on landing phase, the results showed a characteristic that SSJ exerted bigger breaking force and vertical force than LKH.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.94-102
• /
• 2013

We propose the mirror active element pattern (AEP) method for the radiation pattern computation of linear array antennas versus scan angles. The computation time for the radiation pattern of linear array antennas using the mirror AEP method is reduced by almost half compared to that using the AEP method because the number of AEPs of elements obtained by the full-wave simulation necessary for the radiation pattern computation of linear array antennas is reduced by almost half. The difference between the radiation patterns of linear array antennas obtained by the full-wave simulation and mirror AEP method is very small for wide scan angle range when the radiation pattern of an antenna element is symmetric.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.943-953
• /
• 2007

In this paper, we propose a Cassegrain antenna with a scalar feed horn opt rating in Ka-band. For an effective EM simulation of the Cassegrain antenna, the near-field of the feed hone is used ai the equivalent source of the Cassegrain antenna using the surface equivalent theorem. A corrugated circular horn operating with $HE_{11}$ mode is used as the feed horn. The angle and feed center of the main and sub reflectors are optimized to achieve maximum antenna efficiency. The designed feed horn shows the gain of 19dBi, the side-lobe level of less than -25dB and the half power beam width of $20^{\circ}$ at 33 GHz. The Cassegrain antenna shows the gain of 41dBi, the efficiency of 60%, the side-lobe level of less than -20dB and the half power beam width of $1.2^{\circ}$.