• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.743-748
• /
• 2010

Boron nitride (BN) and carbon nitride (CN) films, which have relatively low work functions and commonly exhibit negative electron affinity behaviors, were coated on carbon nanotubes (CNTs) by magnetron sputtering. The CNTs were directly grown on metal-tip (tungsten, approximately 500nm in diameter at the summit part) substrates by inductively coupled plasma-chemical vapor deposition (ICP-CVD). The variations in the morphology and microstructure of CNTs due to coating of the BN and CN films were analyzed by field-emission scanning electron microscopy (FE-SEM). The energy dispersive x-ray (EDX) spectroscopy and Raman spectroscopy were used to identify the existence of the coated layers (CN and BN) on CNTs. The electron-emission properties of the BN-coated and CN-coated CNT-emitters were characterized using a high-vacuum field emission measurement system, in terms of their maximum emission currents ($I_{max}$) at 1kV and turn-on voltage ($V_{on}$) for approaching $1{\mu}A$. The results showed that the $I_{max}$ current was significantly increased and the $V_{on}$ voltage were remarkably reduced by the coating of CN or BN films. The measured values of $I_{max}-V_{on}$ were as follows; $176{\mu}A$-500V for the 5nm CN-coated emitter and $289{\mu}A$-540V for the 2nm BN-coated emitter, respectively, while the $I_{max}-V_{on}$ of the as-grown (i.e., uncoated) emitter was $134{\mu}A$-620V. In addition, the CNT emitters coated with thin CN or BN films also showed much better long-term (up to 25h) stability behaviors in electron emission, as compared with the conventional CNT emitter.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.61-70
• /
• 2004

Generally, ceramics are very difficult-to-cut materials because of its high strength and hardness. The machining process of ceramics can be characterized by cracking and brittle fracture. In the machining of ceramics, edge chipping and crack propagation are the principal reasons to cause surface integrity deterioration. Such phenomenon can cause not only poor dimensional and geometric accuracy, but also possible failure of the ceramic parts. Ceramics can be machined with traditional method such as grinding and polishing. However, such processes are generally cost-expensive and have low material removal rate. Thus, in this paper, to overcome these problems. BN powder, which gives good cutting property, is added for the fabrication of machinable ceramics by volume of 5,10,15,20,25 and 30%. And, mechanical properties, R-curve behavior and machining tests are carried out to evaluate the machining properties of the manufactured machinable ceramics.

• Bulletin of the Korean Chemical Society
• /
• v.6 no.4
• /
• pp.214-217
• /
• 1985

Platinum(II) complexes of R-2,2'-diaminobinaphthyl (R-dabn), [Pt(R-dabn)(H2O)2]Cl2, [Pt(R-dabn)(R-Pn)]Cl2, [Pt(R-dabn)(R-bn)]Cl2, and platinum(II) complexes of S-2,2'-diaminobinaphthyl (S-dabn), [Pt(S-dabn)(H2O)2]Cl2, [Pt(S-dabn)(S-Pn)]Cl2, and [(Pt(S-dabn)(S-bn)]Cl2 have been prepared. (R-Pn and S-Pn are, respectively R- and S isomer of 2,3-diaminobutane). R-Pn and S-bn are, respectively R and S isomer of 2,3-diaminopropane). In the vicinity of the B-absorption band region of dabn, the circular dichroism spectra of platinum(Ⅱ) complexes of R-dabn series show a positive B-band followed by a negative higher energy A-band, which is generally understood as the splitting pattern for a ${\lambda}$ conformation, while the circular dichroism spectra of platinum(Ⅱ) complexes of S-dabn series show a negative B-band followed by a positive higher energy A-band in the long-axis polarized absorption region as expected for a $\delta$ conformation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.407-407
• /
• 2012

화학기상증착법(CVD; Chemical Vapor deposition)으로 h-BN을 증착하여 성장 시간에 따른 표면의 특성 및 결정성을 연구하였다. 암모니아 보레인(BH3NH3)을 보론 나이트라이드(Boron Nitride) 박막의 전구물질로 이용하였으며, $70{\sim}120^{\circ}C$로 열을 가하여 열분해하였다. $25{\mu}m$ 두께의 구리 기판을 챔버에 넣어서 Low pressure (~25 mTorr) 상태가 되도록 한다. 25 mTorr 이하의 압력에서 수소 가스 (0.2~1sccm)를 넣고 $20^{\circ}C$/min로 가열한 후 약 한 시간 후에 $990{\sim}1,000^{\circ}C$가 된다. 그 후 Cu foil의 표면을 부드럽게 하고, 산화막을 제거하기 위해 $990^{\circ}C$에서 40 분간 열처리(annealing)한다. 그 후 암모니아 보레인에서 분해된 보라진 가스(borazine; B3H6N3)로 h-BN을 합성한다. 성장 시간이 길수록 더 많은 부분이 보론 나이트라이드에 의해 덮인다는 것을 관찰하였고, 성장 시 주입하는 수소의 양(0.2~5 sccm)과 알곤(0~15 sccm)의 혼합 비율에 따라 보론 나이트라이드의 domain size가 변화함을 알 수 있었다. 그 각각의 차이를 주사 전자현미경(SEM; Scanning Electron Microscopy)을 통해 확인하고, 결정성을 라만 분광(Raman spectroscopy), 광전자 분광(XPS; X-ray photoelectron spectroscopy)으로 비교 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.213-213
• /
• 2013

Even weak van der Waals (vdW) adhesion between two-dimensional solids may perturbtheir various materials properties owing to their low dimensionality. Although the electronic structure of graphene has been predicted to be modified by the vdW interaction with other materials, its optical characterization has not been successful. In this report, we demonstrate that Raman spectroscopy can be utilized to detect a few % decrease in the Fermi velocity ($v_F$) of graphene caused by the vdW interaction with underlying hexagonal boron nitride (hBN). Our study also establishes Raman spectroscopic analysis which enables separation of the effects by the vdW interaction from those by mechanical strain or extra charge carriers. The analysis reveals that spectral features of graphene on hBN are mainly affected by change in vF and mechanical strain, but not by charge doping unlike graphene supported on $SiO_2$ substrates. Graphene on hBN was also found to be less susceptible to thermally induced hole doping.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.620-624
• /
• 2012

The role of moisture remaining inside the deposition chamber during the formation of the cubic boron nitride (c-BN) phase in BN film was investigated. BN films were deposited by an unbalanced magnetron sputtering (UBM) method. Single-crystal (001) Si wafers were used as substrates. A hexagonal boron nitride (h-BN) target was used as a sputter target which was connected to a 13.56 MHz radiofrequency electric power source at 400 W. The substrate was biased at -60 V using a 200 kHz high-frequency power supply. The deposition pressure was 0.27 Pa with a flow of Ar 18 sccm - $N_2$ 2 sccm mixed gas. The inside of the deposition chamber was maintained at a moisture level of 65% during the initial stage. The effects of the evacuation time, duration time of heating the substrate holder at $250^{\circ}C$ as well as the plasma treatment on the inside chamber wall on the formation of c-BN were studied. The effects of heating as well as the plasma treatment very effectively eliminated the moisture adsorbed on the chamber wall. A pre-deposition condition for the stable and repeatable deposition of c-BN is suggested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.282.1-282.1
• /
• 2016

The remarkable physical properties of two-dimensional (2D) semiconducting materials such as molybdenum disulfide ($MoS_2$) and tungsten disulfide ($WS_2$) etc. have attracted considerable attentions for future high-performance electronic and optoelectronic devices. The ongoing studies of $MoS_2$ based nonvolatile memories have been demonstrated by worldwide researchers. The opening hysteresis in transfer characteristics have been revealed by different charge confining layer, for instance, few-layer graphene, $MoS_2$, metallic nanocrystal, hafnium oxide, and guanine. However, limited works built their nonvolatile memories using entirely of assembled 2D crystals. This is important in aspect view of large-scale manufacture and vertical integration for future memory device engineering. We report $WS_2$ based nonvolatile memories utilizing functional van der Waals heterostructure in which multi-layered graphene is encapsulated between $SiO_2$ and hexagonal boron nitride (hBN). We experimentally observed that, large memory window (20 V) allows to reveal high on-/off-state ratio (>$10^3$). Moreover, the devices manifest perfect retention of 13% charge loss after 10 years due to large graphene/hBN barrier height. Interestingly, the performance of our memories is drastically better than ever published work related to $MoS_2$ and black phosphorus flash memory technology.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1262-1269
• /
• 2002

It is inevitable to evaluate the life of turbine rotor because the operating periods of power plants need to be extended. For the test, seven kinds of specimens with different degradation levels were prepared by the isothermal heat treatment at $630^{\circ}C$. Magnetic methods utilizing Barkhausen noise coercive force($BN_c$) were applied to detect the degradation caused by thermal aging. Magnetic property of material is related with domain dynamics and that is affected by the microstructure of material. Therefore $BN_c$ is very sensitive to the microstructure change of the material. With the increase of degradation, $BN_c$ was decreased and this phenomenon is considered due to precipitations and grain size. The result was compared with Vickers hardness($H_v$) and coercive force($H_c$) to detect the relative variation, and was related with $H_v$ and YS to estimate the change of the mechanical properties with the degradation.

• Journal of Sensor Science and Technology
• /
• v.26 no.6
• /
• pp.379-385
• /
• 2017

In this study, an amperometric non-enzymatic glucose sensor was developed on the surface of a glassy carbon electrode by simply drop-casting the synthesized homogeneous suspension of hexagonal boron nitride (h-BN) nanosheets with a copper metal-organic framework (Cu-MOF) composite. Comprehensive analytical methods, including field-emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), cyclic voltammetry, electrochemical impedance spectroscopy, and amperometry, were used to investigate the surface and electrochemical characteristics of the h-BN-Cu-MOF composite. The FE-SEM, FT-IR, and XRD results showed that the h-BN-Cu-MOF composite was formed successfully and exhibited a good porous structure. The electrochemical results showed a sensor sensitivity of $18.1{\mu}A{\mu}M^{-1}cm^{-2}$ with a dynamic linearity range of $10-900{\mu}M$ glucose and a detection limit of $5.5{\mu}M$ glucose with a rapid turnaround time (less than 2 min). Additionally, the developed sensor exhibited satisfactory anti-interference ability against dopamine, ascorbic acid, uric acid, urea, and nitrate, and thus, can be applied to the design and development of non-enzymatic glucose sensors.

• Corrosion Science and Technology
• /
• v.19 no.1
• /
• pp.23-30
• /
• 2020

Heat sinks are most widely used in thermal management systems; however, the heat dissipation efficiency is usually limited. Therefore, in order to increase heat dissipation efficiency of the heat sink, the heat-dissipating paint using 2D materials (hexagonal boron nitride (h-BN) and graphene) as thermally conductive additive was designed and evaluated in the present study. The heat dissipation performance of the paint was calculated from temperature difference between the paint-coated and -uncoated specimens mounted on the heat source. The highest heat dissipation performance was obtained when the ratio of h-BN to resin was 1/10 in the paint. In addition, further reduction in the temperature of the test specimen by 6.5 ℃ was achieved. The highest heat dissipation performance of the paint prepared using graphene was achieved at a 1/50 ratio of graphene to the resin, and a 6.5 ℃ reduction was attained. In addition, graphene exhibited enhanced corrosion resistance property of heat-dissipating paint by inhibiting the growth of the paint blisters.