• 한국염색가공학회지
• /
• 제9권6호
• /
• pp.33-41
• /
• 1997

This paper surveys the extraction condition of polygenetic natural dye, Sappan Wood and the effect of ash to the dyeability and fastness. The appropriate time for extracting Sappon Wood was 1hour. The pH was increased as the amount of ash increase. The pH was nearly invariable according to the time of ash solution, the extracting times and temperature. Absorbance of dyeing fabrics was about 480nm. From the result of K/S value determination of fabrics, 10g/$\ell$ quantity of ash was surfficient for treatment and the amount of Sappon Wood was in 100% o.w.f.. K/S value of fabrics pre-mordanted or post-mordanted were higher than that of fabrics simultaneous mordanted.K/S value was increased as pH of mordanting bath decrease and pre-mordanting and post-mordanting fabrics increased the amount of absorption (K/S value) compared with non-mordanted fabrics. It was found that pH of mordanting bath affected the amount of absorption and color change of dyed fabrics. Light fastness of fabric dyed was very poor and the fastness of fabric dyed was not influenced by the mordanting conditions and methods.

• 한국지반환경공학회 논문집
• /
• 제11권11호
• /
• pp.37-45
• /
• 2010

본 연구에서는 서해안 ${\bigcirc}{\bigcirc}$지역에서 IPS 지지방식과 Strut 지지방식으로 시공한 현장의 계측에 의한 수평변위량을 수치해석상의 예측치와 비교하고, 실무에서 널리 사용되고 있는 탄소성보법 해석 프로그램(SUNEX, EXCAV)을 이용하여 해석치를 상호 비교분석 하였다. 또 최대수평변위에 대한 여러 제안값 중 점토지반에 적용한 제안값과 비교한 결과, IPS 지지 방식과 Strut지지방식에 의한 최대 수평변위는 IPS지보형식이 Strut지보형식보다 더 크게 발생하였으며, SUNEX 프로그램 해석치와 EXCAV 프로그램 해석치를 상대 비교했을 때 SUNEX 프로그램이 더 크게 해석되었지만, 점토층에서의 기존 제안값인 0.5%H 에는 더 근접하다는 결론을 얻었다. 이는 SUNEX 프로그램이 해석 시 지보형식이나 사용하는 부재 보다는 토질 정수 중 내부마찰각(${\Phi}$)에 의해 수평변위값이 영향을 받기 때문이라 판단된다. 즉 내부 마찰각이 큰 사질토 지반에서는 수평변위값이 작게 발생하고, 내부 마찰각이 작은 점성토 지반에서는 수평변위가 크게 해석되어 상호 비교 시 사질토 지반에서는 EXCAV가 크게 나타나고 점성토 지반에서 SUNEX가 크게 나타났다고 판단된다. 또한, 기존 제안 값 중 점성토에 적용한 0.5%H와 비교 시 현장계측치는 평균 141%, SUNEX로 예측한 결과치는 평균 78.1%, EXCAV로 예측한 결과치는 평균 18.1% 범주에 분포함을 확인하였다. 따라서, 흙막이 가시설 설계 시사용하고 있는 해석 프로그램으로 산정한 수평변위량이 실제 현장에서 계측한 변위량을 과소 예측하므로 지반거동을 모사하는데 주의를 요한다. 추후 보다 정밀한 유한요소해석 등을 통하여 실제 거동의 예측 가능성을 평가해야 할 것이다.

• 수산해양기술연구
• /
• 제17권2호
• /
• pp.77-83
• /
• 1981

하천 오염에서 문제시되고 있는 유기오염 물질인 PCP 와 DDT의 환경기준을 평가하고 담수어 어종간의 독성에 대한 저항성을 연구하였다. 각 어종에 대하여 24, 48, 72 및 96시간의 TL sub(m) 값을 산출하였던 바 오염물질에 대한 저항성은 오염물질의 성상에 따라 상이한 양상을 보여주었다. 실험한 10종의 담수어중 PCP 및 DDT에 저항성이 약한 어종은 N. Chrysophekadion으로 96 h-TL 하(m) 값은 0.065mg/l 과 0.0044mg/l으로 각각 나타났으며 PCP에 저항성이 강한 어종은 T. nilotica로서 96 h-TL 하(m) 값은 0.264mg/l이었으나, DDT에 대해서는 C. Siamensis로서 96 h-TL 하(m) 값은 0.0133mg/l로 평가되었다.

• 동아시아식생활학회지
• /
• 제7권1호
• /
• pp.57-63
• /
• 1997

In order to use leaf mustard Dolsan food preservative ingradient acidity, antimicrobial activity and colors were investigated during pretreatment of leaf mustard Dolsan. pH was remarkably decreased after 8 hours to pretreatment(extracted on shaking) of leaf mustard Dolsan, and no changes were observed after that time. pH of leaf part was higher than stalk after 8 hours storage. Titratable acidity was opposite tendency to the pH. pH was gradually decreased than initial stage during pretreatment of leaf mustard Dolsan at 30, 40 and 5$0^{\circ}C$. After 16 hours pretreatment, the higher pretreatment temperature was, the higher pH was, but after pretreatment for 48 hours, pH of sample pretreated at 5$0^{\circ}C$ was lower than that of sample pretreated at 40 $^{\circ}C$. Antimicrobial activity of leaf mustard Dolsan extract pretreated at 3$0^{\circ}C$ was the strongest of the samples pretreated at 30, 40 and 5$0^{\circ}C$, and that of stalk part was stronger than that of leaf part. L and time. L and b value was higher in the order of samples pretreated at 40, 50 and 3$0^{\circ}C$, and the lower pretreatment temperature was, the higher a value was. L value of stalk part was higher than that of leaf part, but a and b value of leaf part was higher than that of stalk part.

• 약학회지
• /
• 제34권5호
• /
• pp.302-310
• /
• 1990

A study has been made of the Korean bentonite aqueous suspension contrast with American bentonite by means of XRD IR swelling, gel formation and rheogram at various conditions such as concentration, temperature and pH. The Korean bentonite was identified as montmorillonite clay containig a small proprotion of crystoballite and mordenite, and its swelling power were acceptable for requirements of Korean pharmacopeia regulations though its values were not satisfied. Korean bentonite swelled to 10 times and American one did to 15 times compared to its bulkiness of powder. The rheogram of Korean bentonite suspension reveals bulged pseudoplatic flow with yield value at higher concentration and pseudoplastic flow without yield value at lower concentration. The higher the concentration, the greater were the apparent viscosity and hysteresis loop. Korean bentonite suspension showed insignificant temperature dependence on both apparent viscosity and hysteresis loop and it was more temperature dependent on viscosity but less on hysteresis loop than those of American sample. The pH dependence was so high on viscosity that apparent minimum value was near pH 7 and maximum value at pH 3 or 7. The hysteresis loop appeared minimum over the pH range 5-7 and maximum near pH 3 or 11. The Korean bentonite was inferior to the American bentonite in swelling volume, gel formation, thioxotropy, however, it would be possible to improve the quality of Korean bentonite by developing the method of purification for bentonite clay.

• Journal of the Korean Wood Science and Technology
• /
• 제41권5호
• /
• pp.440-446
• /
• 2013

To understand transition characteristics from wood to charcoal, Quercus variabilis wood was carbonized at 200, 250, 300, 340, 540 and $740^{\circ}C$, respectively. Heating value, pH and surface property by FT-IR spectroscopy of the carbonized charcoal were investigated. Heating value and pH increased with increasing carbonization temperature from 4500 cal/g and 4.3 of the control wood to 8,000 cal/g and 9 of the charcoal carbonized at $740^{\circ}C$, respectively. From FT-IR spectroscopy, the peaks from O-H, C-H and C-O stretching disappeared during carbonization at 540 and $740^{\circ}C$. Aromatic skeletal vibration at near $1,506{\sim}1,593cm^{-1}$ was repidly increased until $540^{\circ}C$. These results suggest that the chemical and physical characteristics of wood components in cell wall can be easily changed by increasing carbonization temperature and the carbonization seem to be incomplete at temperature below $540^{\circ}C$.

• Advances in concrete construction
• /
• 제11권5호
• /
• pp.419-428
• /
• 2021

The pH of cement-based materials (CBMs) is an important factor for their durability, sustainability, and long service life. Currently, the use of supplementary cementitious materials (SCMs) is becoming mandatory due to economic, environmental, and sustainable issues. There is a decreasing trend in pH of CBMs due to incorporation of SCMs. The determination of numerical values of pH is very important for various low and high volume SCMs blended cement mortars for the better understanding of different defects and durability issues during their service life. In addition, the effect of cement hydration and pozzolanic reaction of SCMs on the pH should be determined at initial and later ages. In this study, the effect of low and high-volume fly ash (FA) and ground granulated ballast furnace slag (GGBFS) cement mortars in different curing conditions on their pH values has been determined. Thermal gravimetric analysis (TGA) was carried out to support the findings from pH measurements. In addition, thermal conductivity (k-value) and strength activity indices of these cement mortars were discussed. The results showed that pH values of all blended cement mortars were less than ordinary Portland cement (OPC) mortar in all curing conditions used. There was a decreasing tendency in pH of all mortars with passage of time. In addition, the pH of cement mortars was not only dependent on the quantity of Ca(OH)₂. The effect of adding SCMs on the pH value of cement mortar should be monitored and measured for both short and long terms.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 D
• /
• pp.3078-3080
• /
• 2005

본 논문에서는 AF 기능을 구현함에 있어서 2 백만 화소 카메라 모듈인 Sharp LZ0P3731의 기능, AF 모터 (VCM, Voice Coil Motor)에 작용하는 힘과 구동원리, 이를 구동하기 위한 H/W의 설계 특성, 및 DM270을 이용한 AF 제어 시 Focus Value의 특성 분석을 바탕으로 Focus Value 특성을 고려한 최적 AF 알고리즘을 개발하였다. 본 논문에서 제안한 최적 AF 알고리즘은 '최대의 Focus Value가 각 State의 Step Value 마다 각각 다른 위치에서 검출'되는 AF 모터 및 구동 H/W특성을 고려하여, 최적 AF 기능은 최대의 AF Value에 근접하는 Lens Position 제어가 가능하도록 하였다. 이를 검증하기 위한 윈도우용 S/W로 성능을 확인한 결과, 일반적인 AF 기능은 58 프레임으로 3.87초의 시간이 소요되는 반면, 제안한 AF 기능은 25 프레임으로 1.67초로 2배 이상의 빠른 AF 성능을 가졌다.

• 한국염색가공학회지
• /
• 제16권3호
• /
• pp.1-7
• /
• 2004

To study the dyeability(K/S value) and surface color of silk fabrics dyed with Impatiens balsamina extract, its flower, leaf and stem, was extracted by water. This paper investigated some experiments with Impatiens balsamina extract under the various dyeing conditions such as dyeing temperature, dyeing time, repetition of dyeing, dyeing pH with silk fabrics. The results obtained were as follows. 1. It was found that it $\lambdamax$. of silk fabrics dyed with Impatiens balsamina extract was 260nm and its flower, leaf, stem and flowers(white, pink, violet) had same it $\lambdamax$ at 260nm. 2. K/S value was increased when dyeing temperature, repetition of dyeing and time was higher, value of munsell of silk fabrics dyed with Impatiens balsamina extract was yellow-red. dyeing temperature, repetition of dyeing and time was higher, shifted to longer wavelength side. 3. pH added acetic acid was colored reddish yellow-red, but pH added alum was colored yellowish yellow-red in silk fabrics dyed with Impatiens balsamina extract and repetition of dyeing was increased the dye-uptake.

• Corrosion Science and Technology
• /
• 제4권6호
• /
• pp.236-241
• /
• 2005

Hydrogen induced cracking (HIC) is one of the hydrogen degradation phenomena of linepipe steels caused by $H_2S$ gas in the crude oil or natural gas. However, NACE TM0284-96 standard HIC test method is hard to satisfy the steel requirements for sour service application since it uses more severe environmental conditions than actual conditions. Therefore, in order to use steels effectively, it is required to evaluate HIC resistance of steels in the practical range of environmental severity. In this study, HIC resistance of two high strength low alloy (HSLA) steels being used as line pipe steels was evaluated in various test solutions with different $H_2S$ pressures and pH values. The results showed that the key parameter affecting crack area ratio (CAR) is $H_2S$ partial pressure of test solution when the pH value of test solution is not over 4. Hydrogen diffusivity was not a constant value, but it was rather affected by the hydrogen ion concentration (pH value) in the solution.