• Structural Engineering and Mechanics
• /
• v.53 no.2
• /
• pp.311-324
• /
• 2015

The purpose of this study was to investigate experimentally the fatigue performance of reinforced concrete (RC) beams with hot-rolled ribbed fine-grained steel bars of yielding strength 500MPa (HRBF500). Three rectangular and three T-section RC beams with HRBF500 bars were constructed and tested under static and constant-amplitude cyclic loading. Prior to the application of repeated loading, all beams were initially cracked under static loading. The major test variables were the steel ratio, cross-sectional shape and stress range. The stress evolution of HRBF500 bars, the information about crack growth and the deflection developments of test beams were presented and analyzed. Rapid increases in deflections and tension steel stress occured in the early stages of fatigue loading, and were followed by a relatively stable period. Test results indicate that, the concrete beams reinforced with appropriate amount of HRBF500 bars can survive 2.5 million cycles of constant-amplitude cyclic loading with no apparent signs of damage, on condition that the initial extreme tensile stress in HRBF500 steel bars was controlled less than 150 MPa. It was also found that, the initial extreme tension steel stress, stress range, and steel ratio were the main factors that affected the fatigue properties of RC beams with HRBF500 bars, whose effects on fatigue properties were fully discussed in this paper, while the cross-sectional shape had no significant influence in fatigue properties. The results provide important guidance for the fatigue design of concrete beams reinforced with HRBF500 steel bars.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1089-1095
• /
• 2011

Numerical simulation is performed for nucleate boiling on a micro-finned surface, which has been widely used to enhance heat transfer, by solving the equations governing the conservation of mass, momentum, and energy in the liquid and vapor phases. The bubble motion is determined by a sharp-interface level-set method, which is modified to include the effect of phase change and to treat the no-slip and contact-angle conditions, as well as the evaporative heat flux from the liquid microlayer on immersed solid surfaces such as micro fins and cavities. The numerical results for bubble formation, growth, and departure on a microstructured surface including fins and cavities show that the bubble behavior during nucleate boiling is significantly influenced by the fin-cavity arrangement and the fin-fin spacing.

• Journal of the Korean Magnetics Society
• /
• v.19 no.3
• /
• pp.94-99
• /
• 2009

We have studied the effects of oxygen partial pressure change on the physical properties of the $La_{0.7}Ca_{0.3}MnO_3$ thin films grown by Pulsed laser Deposition. Contrary to the previous reports, thin films of high curie temperature were successfully synthesized at very low oxygen partial pressure ($1.0{\times}10^{-5}$, $1.0{\times}10^{-6}Torr$). These observations indicate that the shape of plasma plume and the kinetic energy of the ablated species in it play an important role in determining the quality of samples. We also fabricated p-n heterojunction of $La_{0.7}Ca_{0.3}MnO_3$ and Nb-doped $SrTiO_3$. The current-voltage curves show rectifying behavior and, furthermore, the current responses to the applied magnetic field, indicating a potential possibility of device applications.

• Proceedings of the KOR-BRONCHOESO Conference
• /
• 1993.05a
• /
• pp.85-85
• /
• 1993

The clinical staging system for laryngeal cancers is not sufficient for prognosticator due to different biologic characteristics and their microenvironment according to primary sites. For determining the prognosticators, the authors peformed immunohistochemical staining to EGFR, p53 protein, and pRB in 40 cases of surgically treated squamous cell carcinomas of larynx in our institute during the past 5 years. The results are as followings; 1. The positive expression rate of p53 protein and negative expression rate of pRB showed correlations with clinical parameters. 2. The three-year survival rate for p53 protein positive cases was worse than the p53 protein negative cases. 3. Expression rate of EGFR was not correlated with the clinical parameters. As a conclusion, expression rates of p53 protein and pRB not only reflect well the biologic behavior of laryngeal cancer, but correlate closely with the tumor factors. Therefore they may be useful as the prognosticator to predict the malignant potency of laryngeal squamous cell carcinomas.

• Imaging Science in Dentistry
• /
• v.36 no.3
• /
• pp.169-175
• /
• 2006

The Inflammatory myofibroblastic tumor (inflammatory pseudotumor) is a rarely occurring soft tissue lesion of unknown etiology. It can be of any location, but commonly it is found in lungs. It has been considered as a nonneoplastic reactive inflammatory lesion, but nowadays, confusion and dispute about its character is increasing due to its high recurrence rate and metastasis. We present a patient who had been diagnosed with an inflammatory pseudotumor in the right maxilla area, 1 year before visiting our hospital. After that, her pain and swelling did not resolved and she visit our hospital. On radiographic examination, aggressively infiltrative growth of the lesion with destruction of adjacent bony structure was noted. We found unusual aggressiveness of the inflammatory myofibroblastic tumor of the head and neck region. Because the typical behavior of the inflammatory myofibroblastic tumor is not defined yet, we recommend the surgical excision of the lesion and close follow-up.

• Tuberculosis and Respiratory Diseases
• /
• v.38 no.1
• /
• pp.74-82
• /
• 1991

Bronchial carcinoid is one of the unusual tumors of the lung, accounting for 1 percent of all lung tumors. Carcinoids, like small cell carcinomas, are generally considered to be derived from a neurosecretary type of cell of the respiratory epithelium, the Kulchtsky's cell. So, they are no longer classified as bronchial adenoma, and are recently grouped into the neuroendocrine group of tumors, the so-called APUD (Amine Precursor Uptake Decarboxylase) group of tumors. Although usually characterized by a slow growth pattern and a low incidence of metastatic disease, bronchial carcinoids should no longer be considered as beingn, and a much higher malignant behavior has been described with a special destignation of 'atypical carcinoid'. Bronchial carcinoids are histologically confirmed by the azurophil staining and the presence of the characteristic neurosecretary granule on electron microscopy. Recently we experienced two cases of bronchial carcinoid, the first case, being peripheral-located and histologically proven as atypical carcinoid, and the second, being central-located and hitologically typical. So we report these cases with a review of the literature.

• Child Health Nursing Research
• /
• v.2 no.2
• /
• pp.5-18
• /
• 1996

The purposes of this study were to measure the degree of perceived uncertainty and to identify the rearing attitudes of mothers with chronically ill children, and to examine the relationship between the perceived uncertainty and the rearing attitude of these mothers. The subjects of this study consisted of 133 mothers with chronically ill children, registered at 2 university hospitals in Seoul. Data was collected from April 1 to May 31, 1996. The Parents' Perception of Uncertainty Scale(28-item 4 point scale) and the Maternal Behavior Research Instrument (49-item 5 point scale) were used. Data was analyzed by Cluster analysis, ANOVA MANOVA and t-test. Results of this study are summarized as follows : 1. Mothers perceived their uncertainty to be slightly high (Mn 2.48). The degree of perceived uncertainty by the four components slightly differed unpredictability(2.72), lack in clarity(2.58), vagueness (2.52) and lack of information(2.04) . The degree of perceived uncertainty of mothers with ill children revealed to be influenced significantly by the age of the ill children, duration of illness after the diagnosis, and the experience of hospitalization. 2. Among the rearing attitudes : moderatlely high affective(Mn 3.98) and resrictive(Mn 3.58) attitudes of mothers toward their ill children were identified. Mothers tend to give positive evaluations of their childrens' behaviors (Mn 3.38) and less rejection(Mn 2.81). 3. Mothers' rearing attitude were correlated with the degree of perceived uncertainty in illness ; mothers in the Low Perceived Uncertainty Group (Mn 1.99) revealed the highest affective (Mn 4.08), the lowest resrictive(Mn. 2.72) attitudes and tendency to give positive evaluations of their childrens' behaviors (Mn 3.54) compared to the High Perceived Uncertainty Group(Mn 3.26) and Moderate Perceived Uncertaity Group(Mn 2.57). 4. The degree of perceived uncertainty, the duration of illness after the diagnosis and the experience of hospitalization revealed to be significantly influential to the rearing attitude of mothers with chronically ill children. From the above results, it can be concluded that predicting and controlling mothers' uncertainty are necessary for improved, efficient nursing interventions and normal growth & development of the chronically ill children.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.847-858
• /
• 2013

Since 2001, a series of five irradiation test campaigns for atomized U-Mo dispersion fuel rods, KOMO-1, -2, -3, -4, and -5, has been conducted at HANARO (Korea) in order to develop high performance low enriched uranium dispersion fuel for research reactors. The KOMO irradiation tests provided valuable information on the irradiation behavior of U-Mo fuel that results from the distinct fuel design and irradiation conditions of the rod fuel for HANARO. Full size U-Mo dispersion fuel rods of 4-5 $g-U/cm^3$ were irradiated at a maximum linear power of approximately 105 kW/m up to 85% of the initial U-235 depletion burnup without breakaway swelling or fuel cladding failure. Electron probe microanalyses of the irradiated samples showed localized distribution of the silicon that was added in the matrix during fuel fabrication and confirmed its beneficial effect on interaction layer growth during irradiation. The modifications of U-Mo fuel particles by the addition of a ternary alloying element (Ti or Zr), additional protective coatings (silicide or nitride), and the use of larger fuel particles resulted in significantly reduced interaction layers between fuel particles and Al.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1327-1334
• /
• 1988

In this study rotating bending fatigue tests have been carried out with the deep non-through radial holed notch specimens of low carbon steels(SM 22C). It is investigated that the behaviors of surface and interior fatigue crack propagation and the variations of the shape of the cracked surface on the magnitude of bending stresses. The Obtained results are summarized as follows. (1) The relations between [Crack length] and [Cycle ratio] are expressed by following eq. in the 0.1~0.6 range of N/ $N_{f}$ long[ crack length] = A + B [N/ $N_{f}$ ] In case of surface crack length, values of A and B are uniformed independent upon the magnitude of bending stress, but those are variable according to the magnitude of bending stress for interior crack length. (2) The following eq. is derived on the surface crack propagation rate, bending stress and surface crack length. (dl/dN)=(3.94*10$^{-12}$ ).sigma.$^{4.54}$l (3) Under small stress, interior crack propagation rate increase with the interior crack growth but it decrease for large stress. (4) The shape of cracked surface depends upon the magnitude of bending stress. Under small stress fatigue crack propagates as an semi-ellipse with semi-major axis of surface crack length with semi-major axis of interior crack length for large stress.s.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.627-632
• /
• 1995

W-Cu composites utilize the high electrical conductivity of copper and arc erosion resistance of tungsten to provide properties better suited to electrical contact applications than either tungsten or copper alone. W-Cu composite materials were milled in an attritor with an impeller speed of 300rpm for various milling times. The milled powders were compacted at 300MPa into cylinders, 16m in diameter, and approximately 4m high. Sintering was performed in dry H$_2$at temperature ranging from 1200$^{\circ}C$ to 1400$^{\circ}C$. Samples were sectioned and were polished for scanning electron microscopy (SEM) of microstructures. Homogeneous W-Cu composites were formed after 10 hours mechanical alloying and could be attained 99% density at 1330$^{\circ}C$. As mechanical alloying time increased, Fe-concentration was increased linearly. Intermetallic compound formation interupted the growth of W particles Increased hardness.