• 한국산학기술학회논문지
• /
• 제12권8호
• /
• pp.3723-3728
• /
• 2011

이 연구에서는 암반과 그라우팅 사이의 마찰거동에 대하여 고찰하고자 실내실험과 중대형 실험을 수행하였다. 실내실험의 경우 암반에 대한 모사는 특별히 제작된 원통형 몰드를 통해 구현하였으며 모형토조실험의 경우, 인공암반을 토조에 조성한 후 압력식과 중력식 그라우팅에 따른 그라우트체의 인발거동을 측정하였다. 두 종류의 실험결과 모두 압력식 그라우팅이 암반과 그라우트체의 벽면 마찰거동에 큰 영향을 미치는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.163-170
• /
• 2005

In this paper, the rock bolts, soil nails with filling grout and the micro-piling with injecting grout by pressure were applied for the stabilization of the cut slopes consisting of sedimentary rocks, igneous rocks and metamorphic rocks respectively. The field measurements and 3-D FEM analyses to find out mobilized tensile stresses of the grouted-reinforcing members installed in the drilled holes were executed on each site. With assuming the increments of the cohesive strength in the improved ground, the back analysis using direct calibration approach of changing the elastic modulus of the ground was used to find out the improved elastic modulus which yields the same tensile stresses from field measurements. The results of back analysis show that the elastic modulus of the improved ground were 4 to 6 times as large as the elastic modulus of original ground. Consequently, the design for slope reinforcement to be more rational, it is proposed that not only the improved cohesive strength is to be used in the incremental ranges on well-known previous proposed data, but also the increased elastic modulus which is about 5 times as large as the original elastic modulus is to be considered in design.

• 한국지반공학회논문집
• /
• 제19권4호
• /
• pp.121-131
• /
• 2003

도심지에서 열악한 지반조건에서의 터널 시공을 때때로 불가피 하다. 터널의 안정성 증대와 인접 구조물의 손상을 방지하기 위하여 지반 개량과 보강이 요구된다. 이러한 목적을 달성하기 위해 보조 공법으로 강관 다단 그라우팅은 근래에 국내의 터널 현장에 적용되고 있다. 본 연구에서는 강관 다단 그라우팅으로 보강된 터널의 막장 안정성을 평가하였다. 건조한 지반에서는 지보압이 강관 다단 그라우팅으로 인해 크게 감소하지 않으나 지하수위 하에서 터널시공 시 터널 막장에 발생하게 되는 침투수력은 상대적으로 크게 감소하였다. 투수계수의 이방성이 터널 막장에 작용하는 침투수력에 미치는 영향은 역학해석과 지하수 흐름해석의 연계해석을 통하여 검토되었다. 수직방향에 비해 수평방향의 투수계수가 큰 경우 터널 막장에 작용하는 침투수력은 감소하였다.

• Geomechanics and Engineering
• /
• 제20권1호
• /
• pp.67-73
• /
• 2020

With the increasing number of underground projects, the problem of rock-water coupling catastrophe has increasingly become the focus of safety. Grouting reinforcement is gradually applied in subway, tunnel, bridge reinforcement, coal mine floor and other construction projects. At present, cement-based grouting materials are easy to shrink and have low strength after solidification. In order to overcome the special problems of high water pressure and high in-situ stress in deep part and improve the reinforcement effect. In view of the mining conditions of deep surrounding rock, a new type of cement-based reinforcement material was developed. We analyses the principle and main indexes of floor strengthening, and tests and optimizes the indexes and proportions of the two materials through laboratory tests. Then, observes and compares the microstructures of the optimized floor strengthening materials with those of the traditional strengthening materials through scanning electron microscopy. The test results show that 42.5 Portland cement-based grouting reinforcement material has the advantages of slight expansion, anti-dry-shrinkage, high compressive strength and high density when the water-cement ratio is 0.4, the content of bentonite is 4%, and the content of Nano Silica is 2.5%. The reinforcement effect is better than other traditional grouting reinforcement materials.

• 한국지반신소재학회논문집
• /
• 제16권2호
• /
• pp.149-158
• /
• 2017

저수지 제방의 그라우팅시 가장 이상적인 주입형태는 침투주입이지만 일반적으로 침투와 할렬주입이 복합적으로 시공되어 원지반의 교란이 발생될 가능성이 존재한다. 이와 같은 문제점을 개선하기 위하여 이상적인 침투주입을 가능하게 하는 그라우트 재료를 이용하여 저압주입과 팽창제를 이용한 주입재의 팽창력으로 그라우팅 주입공 주변에 대한 다짐을 실시하고 순차적으로 그라우트재를 주입하는 방법이 유용하다. 본 연구에서는 그라우트 주입공 주변에 대한 침투다짐효과를 얻기 위하여 하이브리드형 주입재와 팽창제를 혼합한 침투다짐 그라우트를 PC(Permeable Compaction)팩커를 이용하여 주입한 그 효과에 대해 고찰하였다, 본 연구결과, PC팩커와 침투다짐 그라우트를 저수지 보수보강 그라우팅 공사에 적용할 경우 저수지 차수 그라우팅의 성능기준에 부합하는 침투다짐효과가 발휘될 수 있음을 확인하였다.

• 한국터널지하공간학회 논문집
• /
• 제23권5호
• /
• pp.281-302
• /
• 2021

철도망 구축이 확대되는 추세 속에 도심지나 한강을 통과하기 위해 TBM 굴착공법 적용사례가 증가하고 있다. 특히, 도심지나 한강하저를 통과하는 경우 불량한 지반 및 지하수조건을 조우하게 되며 안정적인 굴진 및 커터교체(Cutter Head Intervention, CHI)를 위해서 그라우팅을 적용하고 있다. 본 논문에서는 TBM 굴착공법을 적용한 철도 터널 시공 시 적용한 그라우팅에 대하여 소개하고자 한다. 특히, CHI를 위해 그라우팅을 수행한 사례에 대한 소개나 분석이 많지 않은 것으로 판단하여 CHI를 위한 그라우팅 범위산정, 수행결과, 고찰 및 제언(Lessons Learned)을 기술하고자 한다. 그라우팅은 막장안정성을 확보하는 목적이 있으며, 작업위치에 따라 지상(수직)그라우팅과 TBM 장비 내에서 수행하는 갱내 그라우팅으로 나눌 수 있다. 갱내그라우팅을 수행한 결과 공기 및 보강효과 측면에서 지상(수직) 그라우팅에 비해 비효율적이라고 판단되어 지상그라우팅으로 계획을 변경하였다. 한강하저 구간의 경우 슬러지 발생으로 인한 환경오염, 주입재 유실 등이 우려되어 고압분사그라우팅을 적용할 수 없었으며 대안으로 수중불분리 주입재를 적용한 저압그라우팅을 적용하였다. 육상구간은 지상 작업부지를 확보할 수 있어 고압분사그라우팅을 적용하였다. 실제 그라우팅을 수행한 결과를 소개함으로써 향후 쉴드 TBM을 적용한 터널 시공 중 CHI 시 지반조건에 따른 적합한 그라우팅 공법 및 방법을 결정하는데 기초자료로 활용될 수 있을 것으로 기대된다.

• Geomechanics and Engineering
• /
• 제35권1호
• /
• pp.29-39
• /
• 2023

As the intensity of urban underground space development increases, more and more tunnels are planned and constructed, and sometimes it is inevitable to encounter situations where tunnels have to underpass the river embankments. Most previous studies involved tunnels passing river embankments perpendicularly or with large intersection angle. In this study, a project case where two EPB shield tunnels with 8.82 m diameter run parallelly underneath a river embankment was reported. The parallel length is 380 m and tunnel were mainly buried in the moderate / slightly weathered clastic rock layer. The field monitoring result was presented and discussed. Three-dimensional back-analysis were then carried out to gain a better understanding the interaction mechanisms between shield tunnel and embankment and further to predict the ultimate settlement of embankment due to twin-tunnel excavation. Parametrical studies considering effect of tunnel face pressure, tail grouting pressure and volume loss were also conducted. The measured embankment settlement after the single tunnel excavation was 4.53 mm ~ 7.43 mm. Neither new crack on the pavement or cavity under the roadbed was observed. It is found that the more degree of weathering of the rock around the tunnel, the greater the embankment settlement and wider the settlement trough. Besides, the latter tunnel excavation might cause larger deformation than the former tunnel excavation if the mobilized plastic zone overlapped. With given geometry and stratigraphic condition in this study, the safety or serviceability of the river embankment would hardly be affected since the ultimate settlement of the embankment after the twin-tunnel excavation is within the allowable limit. Reasonable tunnel face pressure and tail grouting pressure can to some extent suppress the settlement of the embankment. The recommended tunnel face pressure and tail grouting pressure are 300 kPa and 550 kPa in this study, respectively. However, the volume loss plays the crucial role in the tunnel-embankment interaction. Controlling and compensating the tunneling induced volume loss is the most effective measure for river embankment protection. Additionally, reinforcing the embankment with cement mixing pile in advance is an alternative option in case the predicted settlement exceeds allowable limit.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2102-2107
• /
• 2007

GSHP systems are used for air-conditioning systems in commercial buildings, schools, and factories because of low operating and maintenance costs. These systems use the earth as a heat source in heating and a heat sink in cooling mode. Ground heat exchangers are classified by a horizontal and vertical type according to the installation method. Vertical type is usually constructed by placing small diameter high density polyethylene tube in a vertical borehole. Vertical tube sizes range from 20 to 40 mm nominal diameter. Borehole depth range between 100 and 200 m depending on local drilling conditions and available equipment. In this study, to evaluate the performance of single u-tube with bentonite grouting, single u-tube with broken stone grouting and double u-tube bentonite grouting of vertical ground heat exchangers, test sections are buried on the earth and experimental apparatus is installed. Therefore the heat transfer performance and pressure loss of these are estimated.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.466-469
• /
• 2007

Heat pumps are used for air-conditioning systems in commercial buildings, schools, and factories because of low operating and maintenance costs. These systems use the earth as a heat source in heating mode and a heat sink in cooling mode. Ground heat exchangers are classified by a horizontal type and vertical type according to the installation method. A horizontal type means that a heat exchanger is laid in the trench bored in 1.2 to 1.8 m depth. And a vertical type is usually constructed by placing small diameter high density polyethylene tube in a vertical borehole. Vertical tube sizes range from 20 to 40 mm nominal diameter. Borehole depth range between 100 and 200 m depending on local drilling conditions and available equipment. In this study, to evaluate the performance of single u-tube with bentonite grouting, single u-tube with broken stone grouting and double n-tube bentonite grouting of vertical ground heat exchangers, test sections are buried on the earth and experimental apparatus is installed. Therefore the heat transfer performance and pressure loss of these are estimated.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.267-278
• /
• 2010

To improve the grout penetration characteristics, vibration method was adopted in this study. The grout material perturbed by cyclic vibration is injected into the ground. By applying the vibrating flow system, cement particles will become less adhesive and the clogging tendency will be decreased. A series of pilot-scale chamber tests were performed to verify the enhancement of the groutability by applying the vibratory grout injection; assessment on change of the lumped parameter $\theta$ which represents a barometer of clogging phenomenon was made. Moreover, the effect of vibratory grout injection through the joint was also investigated using artificially made rock joints. Experimental results as well as analytical results show that the grout penetration depth can be substantially improved by vibration grouting. Moreover, it was found that enhancement of the permeation grouting due to vibratory injection is more dominant at low grouting pressure of less than 400kPa.