• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.2
• /
• pp.325-328
• /
• 2020

This paper demonstrated a voltage-controlled oscillator (VCO) using cost-effective (1-poly 6-metal) mixed signal standard CMOS process. To have the high-quality factor inductor in LC resonator with thin metal thickness, patterned-ground shields (PGS) was adopted under the spiral to effectively reduce the ac current of low resistive Si substrate. And, because of thin top-metal compared with that of RF option (2 ㎛), we make electrically connect between the top metal (M6) and the next metal (M5) by great number of via array along the metal traces. The circuit operated from 2.48 GHz to 2.62 GHz tuned by accumulation-mode varactor device. And the measured phase noise of LC VCO has -123.7 dBc/Hz at 1MHz offset at 2.62 GHz and the dc-power consumption shows 2.07 mW with 1.8V supply voltage, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.112-116
• /
• 2022

The demand for a rear reflective material is continuing according to the expansion of the bifacial soar module and the effect on the re-reflection of the ground using a back sheet that is not used due to the increase in the supply of the bifacial solar module was confirmed. For analysis, a bifacial solar module with an output of 445W was connected to a single inverter of 49.84kW, and analysis of each two inverters was carried out. In the analysis of the results, it was confirmed that the generation amount increased by 5.25% compared to the case where the back sheet reflective film was not installed and it was confirmed that the increase in the generation amount was the noon time when strong solar radiation was irradiated, not the time of sunrise and sunset.

• Journal of the Korean Society for Railway
• /
• v.17 no.2
• /
• pp.94-99
• /
• 2014

Recently, trends in new transportation system development have been primarily focused on sustainable and ecofriendly mobility solutions. The personal rapid transit (PRT) system has been considered a promising candidate in this category; its competitiveness is being improved through convergence with cutting-edge electric vehicle (EV) technologies. However, battery-powered vehicles pose difficult technical challenges in attempts to achieve reliable and efficient operation. In this study, a design approach for a solar-power assisted PRT system is presented with small-scale demonstrations aimed at circumventing challenges facing its adoption, as well as helping speed the transition to electric-powered ground transportation. From the results, it is expected that flexible photovoltaic (PV) cells will be able to supply 11% of the power required by the service equipment installed in a prototype vehicle. In particular, flexible photovoltaic (PV) cells are advantageous in terms of cost, weight, and design considerations. Most importantly, the cells' flexibility and attach-ability are expected to give them great potential for extended application in various areas.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.14 no.1
• /
• pp.2535-2548
• /
• 1972

Instead of fertilizing the lands they moved to find other fertile lands and lived a feudal life agriculture and various machincs played a main role in the land reclamation. The best method of land clearing, the time and capacity in the operation and the effect of growing crops should systematically analized prior to the time of 3rd Five-year Economic Development(1972-1976) in order to cultivate 210,000ha of wasteland or the modernization of our country. The present study was investigated to find out a new working-system of mechanical land clearing and development of fertile soil. The results are as follows: 1) The first stage of productive power increases when weeds were mixed soil in the land clearing work in order to supply organic materials and to make soil swollen instead of burning or just removing. 2) The equipments such as bulldozers, harrows, power tillers and so on should be prepared in order to do a systematic work in the land clearing. 3) The work of pulling-up roots is dependent upon the forms of roots spreading under the ground. The work of the pulling-up of the straight roots was most difficult. But before the roots are pulling-up we do not know the forms of roots. 4) The cutting of soil from upside to under side land clearing method (II) Spent 6 hr 7 min 43 sec per 1 Danbo in doing land clearing and control method spent 4 hr 52 min 30 sec per 1 Danbo in doing land cearing. No significant difference could be found between II treatment type and I treatment type. 5) The volume of soil carried by bulldozer $270.38m^3$ per 1 Danbo in I type and in II type, $368.58m^3$ per 1 Danbo or about 36% increased in II type then in I type. But that is not a significant difference when considering the whole productive power of soil. 6) The land clearing of terrace by bulldozers cannot escape making the embankment slope of about $45^{\circ}$, and 25.3% should be decreased in the area. It is recommended to make use of the embankment slope by planting grass for cows. 7) The time of retary tilling increased 2.3 times or 1 hr 42 min 22 sec per 1 Danbo compared to the timesrequired in the harrowing. Because it mixed the Organic matter on ground and the harrowing of subsoil. 8) The havest of pasture growing on the land reclamation in natural slope is as follows. (a) The none fertilizers with reclaimed block of productivity decresed 1/10 than that of the farmland. Therefore the none fer tilizing in the cultivated pasture is unprofitable. (b) The havest of the manured IV treatment block was the best not only in the kinds of fertilizers but also in the kinds of pasture grass.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.4
• /
• pp.63-68
• /
• 2010

Utility-Pipe Conduit is, Housing and city effectively accommodate what they absolutely need power, communications, gas, pipeline, water supply, drainage, energy facilities etc, according to expansion of urban infrastructure are derived, several ways to solve problems in, collection facilities in place are maintained and managed facility. If Utility-Pipe Conduit is damaged, as well as national security, because their impact on society as a whole, by introducing large vulnerability in the fire prevention activities and suppression measures and disaster for our situation by introducing measures, comprehensive analysis of the fire risk, it shall establish fire prevention activities and suppression through analysis of Utility-Pipe Conduit design, institutional issues, the problem of fire protection facilities, fire spread phenomenon etc. Because of Utility-Pipe Conduit is an enclosed place, so incomplete combustion due to lack of oxygen supply that there are problem such dark smoke, carbon monoxide etc, toxic combustion products and heat generation and visual impairment is an issue difficult to enter. As well as fire prevention activities, the fire In light of the particularity of the under ground than above ground fire, so this phenomenon is weak fire fighting that fire to become effective fire fighting tactics, basically it is necessary difficulty softening, non-burn softening and prevent combustion expansion of the cable is installed on the Utility-Pipe Conduit, having to considering the specificity of the response command system and relevant organizations to establish an on-site, Structural identification and other information gathering required to record of Response agencies, keep air conditioning system 24 hours and strengthening Virtual Total Training of Response agen

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.269-269
• /
• 2012

A new ion source has been designed, fabricated, and installed at the NBTS (Neutral Beam Test Stand) at the KAERI (Korea Atomic Energy Research Institute) site. The goalis to provide a 100 keV, 2MW deuterium neutral beam injection as an auxiliary heating of KSTAR (Korea Super Tokamak Advanced Research). To cope with power demand, an ion current of 50 A is required considering the beam power loss and neutralization efficiency. The new ion source consists of a magnetic cusp bucket plasma generator and a set of tetrode accelerators with circular copper apertures. The plasma generator for the new ion source has the same design concept as the modified JAEA multi-cusp plasma generator for the KSTAR prototype ion source. The dimensions of the plasma generator are a cross section of $59{\times}25cm^2$ with a 32.5 cm depth. The anode has azimuthal arrays of Nd-Fe permanent magnets (3.4 kG at surface) in the bucket and an electron dump, which makes 9 cusp lines including the electron dump. The discharge properties were investigated preliminarily to enhance the efficiency of the beam extraction. The discharge of the new ion source was mainly controlled by a constant power mode of operation. The discharge of the plasma generator was initiated by the support of primary electrons emitted from the cathode, consisting of 12 tungsten filaments with a hair-pin type (diameter = 2.0 mm). The arc discharge of the new ion source was achieved easily up to an arc power of 80 kW (80 V/1000 A) with hydrogen gas. The 80 kW capacity seems sufficient for the arc power supply to attain the goal of arc efficiency (beam extracted current/discharge input power = 0.8 A/kW). The accelerator of the new ion source consists of four grids: plasma grid (G1), gradient grid (G2), suppressor grid (G3), and ground grid (G4). Each grid has 280 EA circular apertures. The performance tests of the new ion source accelerator were also finished including accelerator conditioning. A hydrogen ion beam was successfully extracted up to 100 keV /60 A. The optimum perveance is defined where the beam divergence is at a minimum was also investigated experimentally. The optimum hydrogen beam perveance is over $2.3{\mu}P$ at 60 keV, and the beam divergence angle is below $1.0^{\circ}$. Thus, the new ion source is expected to be capable of extracting more than a 5 MW deuterium ion beam power at 100 keV. This ion source can deliver ~2 MW of neutral beam power to KSTAR tokamak plasma for the 2012 campaign.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.02a
• /
• pp.220-237
• /
• 2004

China, as a developing country with a great number of population and relatively less energy resources, reasonably emphasizes the nuclear energy utilization development. For the long term sustainable energy supply, as for nuclear application the basic strategy of PWR-FBR-Fusion has been settled and envisaged. Due to the economy and experience reasons the nuclear power and technology development with a moderate style are kept in China up to now. In China mainland apart from two NPPs with the total capacity of 2.1 GWe in operation, four NPPs are under construction and two NPPs are planned for the Tenth Five Year Plan(2001-2005). Also another one or two NPPs are still in discussion. It could be foreseen that the total nuclear power capacity will reach 8.5GWe before the year 2005 and 14-15 GWe before 2010 respectively. As the first step for the Chinese fast reactor engineering development the 65MWt China Experimental Fast Reactor(CEFR) is under construction. The main components of primary, secondary and tertiary circuits and of fuel handling system have been ordered. The reactor building under construction has reached the top namely 57m above the ground. More than one hundred components and shielding doors have been installed. It is planned that the construction of reactor building with about 40,000$m^2$ floor surface will be completed in the end of the year 2002 and envisaged that the first criticality of the CEFR will be in the end of 2005. The second step of the Chinese fast reactor engineering development is a 300MWe Prototype Fast Breeder Reactor which is only under consideration up to now. Some important technical selections have been settled, but its design has not yet started.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.4 s.310
• /
• pp.53-59
• /
• 2006

This paper describes the new design technique of full wave rectifier (FWR) for precise measurement instrument and the chip implementation of this FWR circuit with measurement results. Conventional circuits have some problems of complex design and limited output range( $VDD/2{\sim}VLIIV1IT+$). Proposed FWR circuit was simply designed with two 2x1 MUXs, one high speed comparator, and one differential difference amplifier(DDA). One rail-to-rail differential difference amplifier(DDA) performs the DC level shifting to VSS and 2X amplification simultaneously, and enables the full range ($Vss{\sim}VDD$) operation. The proposed FWR circuits shows more than 50% reduction of chip area and power consumption compared to conventional one. Proposed circuit was implemented with 0.35um 1-poly 2-metal CMOS process. Core size is $150um{\times}450um$ and power dissipation is 840uW with 3.3V single supply.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• The Journal of Fisheries Business Administration
• /
• v.24 no.2
• /
• pp.1-16
• /
• 1993

Because of the radical changes in the domestic and foreign economic circumstances Koreaa fisheries is confronted with difficulties. Along the end of the UR marine products of other nations are rushing into Korea. Also migration of labor to other industries and rise of wage level in Korean fisheries deteriorate managerial conditions. But in Korea which has little natural resourses fisheries is still more important. That is \circled1 creating job opportunites \circled2 increase of income \circled3 supply of foodstuffs and animal protein \circled4 acquisition of foreign currency \circled5 enlargement of domestic market for industrial products \circled6 development of other interrelated industries \circled7 rational use of domestic resourses \circled8 diversification of population and production activites \circled9 contribution to balanced growth of national economy by the developing regional economy. These roles of fisheries in national economy mentioned above are to be excuted forward. In spite of the radical change in the economic circumstances at the end of the UR fisheries if crucial in Korea as a industry. For this our fisheries is to be made to compete with foreign fisheries. Through the cheap price and high quality our fisheries must be came to compete with foreign fisheries and meet the people's needs for marine products. For this it is necessary to maintain high productivity and competitive power. Now with the exception of a portion of the deep - sea fishing, our fisheries is generally paltry, Especially inshore fishery which is the main stock in our fisheries is very paltry and so productivity and competetive power are very low. So to develop our fisheries which has s comparative disadvantage active polices that follows below are to be promoted on a large scale. \circled1 improvement of structure \circled2 augmentation of productivity in fishing ground by making fisheries resourses \circled3 enlargement of finantial and monetary assistance \circled4 effective administration of fisheries cooperative union \circled5 activation of R&D etc These polices which need to be scientific and comprehensive are very valuable. Especially without making fishieries resources we cannot expect economy of scale, promotion of productivity and development of fisheries. And we do also endeavour to gather the results of the study and investigation about fisheries domestic and foreign and do ceaselessly put these to practical use systimatically.