• The Korean Journal of Zoology
• /
• v.27 no.3
• /
• pp.127-136
• /
• 1984

The specification of dorsal/ventral axis in the egg of Xenopus laevis was investigated as a series of oblique orientation to gravity by tilt and clinostat. The results are as follows. (1) If the eggs were oriented, in the early period after fertilization, to novel gravity by $15^\\circ, 30^\\circ, 45^\\circ$ and $60^\\circ$ tilt until gastrula stage, the site of involution was usually formed in the OpG side (the side opposing gravity). As the degree of tilt was raised from $15^\\circ to 60^\\circ$, the rate of relocation of the involution site was proportionally increased. (2) When UV-irradiated eggs were tilted period to first cleavage by $15^\\circ, 30^\\circ, 45^\\circ$ and $6\^\\circ$, the effect of UV syndrome was rescued, and the extent of rescue was propotional to the tilt degree. (3) The fertile eggs were loaded on the clinostats of several speeds. In the range of low speeds between $0.45 \\sim 9.0$ rph, the location of dorsal lip was dependent on the direction of rotation, and in $40 \\sim 360$ rph, lip was formed at a random position. In addition, some of the tadpoles experienced with clinostat showed the typical syndrome of "dorsal axis reduction". The above results were discussed regarding the mechanism of the establishment of dorsal/ventral palarity. palarity.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.2
• /
• pp.185-198
• /
• 2017

The application of composites as an alternative material for marine steel hatch covers is the subject of this study. Two separate approaches are considered; weight reduction approach and strengthening approach. For both approaches Finite Element Analysis (FEA) was performed using ANSYS software. Critical design parameters of the composite hatch cover and FEA are discussed in details. Regarding the weight reduction approach; steel hatch covers of a bulk carrier were replaced by composite covers and a weight reduction of 44.32% was achieved leading to many benefits including fuel saving, Deadweight Increment and lower center of gravity of the vessel. For the strengthening approach; the foremost hatch cover was strengthened to withstand 150% of the load required by IACS for safer navigation while no change in weight was made between the steel and composite covers. Results show that both approaches are feasible and advantageous.

• Journal of Powder Materials
• /
• v.11 no.1
• /
• pp.28-33
• /
• 2004

In the present study, the focus is on the analysis of carbothermal reduction of the titanium-cobalt-oxygen based oxide powder by solid carbon for the optimizing synthesis process of ultra fined TiC/Co composite powder. The titanium-cobalt-oxygen based oxide powder was prepared by the combination of the spray drying and desalting processes using the titanium dioxide powder and cobalt nitrate as the raw materials. The titanium-cobalt-oxygen based oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under a flowing argon atmosphere. The changes in the phase structure and thermal gravity of the mixture during carbothermal reduction were analysed using XRD and TGA. The synthesized titanium-cobalt-oxygen based oxide powder has a mixture of $TiO_2$ and $CoTiO_3$. This oxide powder was transformed to a mixed state of titanium car-bide and cobalt by solid carbon through four steps of carbothermal reduction steps with increasing temperature; reduction of $CoTiO_3$ to $TiO_2$ and Co, reduction of $TiO_2$, to the magneli phase($Ti_nO_{2n-1}$, n>3), reduction of the mag-neli phase($Ti_nO_{2n-1}$, n>3) to the $Ti_nO_{2n-1}$(2$\leq$n$\leq$3) phases, and reduction and carburization of the $Ti_nO_{2n-1}$(2$\leq$n$\leq$3) phases to titanium carbide.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.2
• /
• pp.50-57
• /
• 2004

Mercurous Bromide ($Hg_2Br_2$) crystals hold promise for many acousto-optic and opto-electronic applications. This material is prepared in closed ampoules by the physical vapor transport (PVT) growth method. We investigate the effects of solutal convection on the crystal growth rate in a horizontal configuration for diffusive-convection conditions and purely diffusion conditions achievable in a low gravity environment. Our results show that the growth rate is decreased by a factor of one-fourth with a ten reduction of gravitational acceleration near y = 2.0 cm. For 0.1 $g_O$ the growth rate pattern exhibits relatively flat which is intimately related to diffusion-dominated processes. The growth rate nonuniformity is regardless of aspect ratio across the interfacial positions from 0 to 1.5. Also, the effect of a factor of the ten reduction in the gravitational acceleration is same to both Ar = 5 and 2. The enlargement in the molecular weight of B from 50 to 500 by a factor 4 causes a decrease in the maximum growth rate by the same factor, indicative of the effect of solutal gradients.

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.3
• /
• pp.26-31
• /
• 2021

Advanced classification of Cs contaminated soil by using a magnetic force-assisted selection pipe was investigated. A selection pipe is a device that sort particles depending on their particle size, based on the relationship between buoyancy, drag, and gravity force acting on the particles. Radioactive cesium is concentrated in small-particle size soil components with a large specific surface area. Hence, the volume of the Cs contaminated soil can be reduced by recycling the large-particle size soil components with low radioactive concentration. One of the problems of the selection pipe was that the radioactive concentration of the stayed soil in the selection pipe exceeds 8000 Bq/kg, which is the standard value of recycling of Cs contaminated soil, due to low classification accuracy. In this study, magnetic fields were applied to the lab-scale selection pipe from upper side to improve the classification accuracy and to reduce the radioactive concentration of the stayed soil.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.807-815
• /
• 2013

A numerical study on soot formation in a laminar ethylene diffusion flame at atmospheric pressure was conducted to obtain a better understanding of the effects of buoyancy on sooting flames under 0g and 1g using a gas-phase reaction mechanism and thermal and transport properties. A simple model was employed to predict soot formation, growth and oxidation with interactions between the gas phase chemistry and the soot chemistry taken into account. Results showed that the flames in 0g are much wider than that of 1g because of the thicker diffusion layer and reduction in axial velocity. The reduction in the axial velocity in 0g results in longer residence times, and resulting in greatly enhanced soot volume fraction. And, under zero-gravity, due to the lack of a buoyancy-induced instability, flame instability disappears.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.7 no.2
• /
• pp.105-111
• /
• 1999

This study was performed about composting in a batch reactor of laboratory scale using garbage waste and swine waste. Sawdust and coconut peat were materials to control optimum moisture, C/N ratio and specific gravity in the study. Comparing compost using only sawdust with compost using sawdust and coconut peat, the latter was higher at reduction rate and decomposition rate. Coconut peat was accelerated aerobic fermentation, because it had moisture holding ability, initial moisture was low, ventilation was good and control of optimum specific gravity was possible. Compost by only garbage waste was under standard of manure. but mixtures in same proportion of garbage waste and swine waste producted high quality compost. CEC value was average 63.8me/100g. The initial C/N ratio of compost was regulated effectively because of high C/N ratio of sawdust. As the C/N ratio(>40) was higher, reduction rate was higher. During the composting C/N ratio was improved more and more.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.12
• /
• pp.39-52
• /
• 2011

This paper describes a new numerical analysis technique in stability analysis for a slope reinforced with pressure grouted soil nails. The installing effect of pressure grouted soil nails can be simulated in this method. Shear strength reduction method associated with finite element method is used for slope stability analysis. Factors of safety for a slope reinforced with pressure grouted soil nails are compared with those for a natural slope and a slope reinforced with gravity grouted soil nails in order to investigate their reinforcing effects. More than 50% increase in the factor of safety is obtained when the slope is reinforced with pressure grouted soil nails compared to the one with gravity grouted soil nails. The reinforcing effects of pressure grouted soil nails become obvious with increase in their length. The reinforcing mechanism of the pressure grouted soil nails for the slope stability can be explained by the slope failure surface expanding gradually toward the backfill. The increased stability of the slope reinforced with pressure grouted soil nails results mainly from their improved pull-out resistance.

• Computers and Concrete
• /
• v.20 no.6
• /
• pp.663-670
• /
• 2017

The post-tensioned (PT) flat plate slab system is commonly used in practice, and this simple and fast construction method is also considered to be a very efficient method because it can provide excellent deflection and crack control performance under a service load condition and consequently can be advantageous when applying to long-span structures. However, a detailed design guideline for evaluating the lateral behavior of the PT flat plate slab system is not available in current design codes. Thus, typical design methods used for conventional reinforced concrete (RC) flat plate slab structures have inevitably been adopted in practice for the lateral load design of PT flat plate structures. In the authors' previous studies, the unified equivalent frame method (UEFM) was proposed, which considers the combined effect of gravity and lateral loads for the lateral behavior analysis of RC flat plate slab structures. The aim of this study is to extend the concept of the UEFM to the lateral analysis of PT flat plate slab structures. In addition, the stiffness reduction factors of torsional members on interior and exterior equivalent frames were newly introduced considering the effect of post-tensioning. Test results of various PT flat plate slab-column connection specimens were collected from literature, and compared to the analysis results estimated by the extended UEFM.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.1
• /
• pp.22-32
• /
• 2023

In general, when scrap is dissolved in an electric arc furnace, the amount of electric furnace steel dust (EAFD) generated is about 1.5% of the scrap charge amount, and the electric furnace steel dust collected by the bag filter is charged into the Rotary Kiln or Rotary Hearth Furnace (RHF), and the zinc component is recovered as crude zinc oxide, at which time a clinker of Fe-Base is generated. In this research, first, for the efficient resource conversion of electric furnace steel dust, a reduction and roasting experiment was conducted and the reaction kinetics was examined. As a result of the experiment, it was observed that the reduction and roasting reaction was actively conducted in the range of 1100~1150℃, and melting occurred in the range of 1250℃. In the past, this clinker was widely used as a roadbed material for road construction and an Fe-Source for cement production, but in recent years, it has been mainly reclaimed due to strengthening environmental standards. However, landfill treatment is by no means a desirable treatment method due to environmental pollution caused by leachate, expensive landfill costs, and waste of Fe resources. Therefore, in order to more actively recycle the Fe component in the clinker, first of all the clinker was pulverized into an optimal particle size, and anthracite and binder (starch) were added to the magnetic material obtained by specific gravity and magnetic separation for briquet. As a experimental results, it was possible to efficiently separate clinker as Fe component and other slag component by specific gravity and magnetic force. As a results of loading and dissolving the manufactured briquet clinker in an electric arc furnace, it was observed that the unit of power and production yield were clearly improved and the carbon addition effect in molten metal was also somewhat.