• 한국산업융합학회 논문집
• /
• 제24권4_2호
• /
• pp.501-507
• /
• 2021

In this study, In order to prevent the safety accidents caused by the sliding, to develop the non-slip grating, the stability judgment based on the span length of the grating and the gap of the bearing bar is performed. The structural analysis of Grating was carried out in accordance with the provisions set out in Grating's load-bearing test conditions. As the span length increases, the deflection increases and the stress and span length tend to be proportional to each other. It was shown that the larger the span, the linear increase in stress and exponential increase in deformation of grating. The maximum stress of grating was approximately 58.2 MPa, indicating a very stable safety rate of about 4.3 compared to the yield strength of the grating material. Based on these results, it will be able to be utilized as the basic data for determining the optimal dimensions of non-slip grading by performing optimal designs in the future.

• Composites Research
• /
• 제17권4호
• /
• pp.32-39
• /
• 2004

여러 광섬유 센서 중에서, FBG 센서는 다중화의 큰 장점으로 인해 다른 광섬유 센서에 비해 더 활발히 연구가 진행되고 있다. 최근, FBG 센서의 적용 연구는 부착보다는 복합재료 내부에 삽입 적용되는 경우가 많아지고 있다. 하지만, FBG 센서의 삽입 시 복합재료의 강화섬유와 평행하지 않게 삽입할 경우 발생하는 센서의 복굴절 현상으로 인해 삽입에 많은 제한이 있었다. 본 연구에서는 제작이 간편하고 다중화에 영향을 받지 않으며 복합재료 내부에 삽입 시 복굴절의 영향으로부터 보다 안정한 다양한 격자 길이의 FBG 센서 제작 기법에 대해 연구하였다. 그리고, 2 가지 종류의 복합재료에 대한 성형 모니터링을 통해 제작된 센서의 신호 특성에 대해 고찰하였다.

• Current Optics and Photonics
• /
• 제7권1호
• /
• pp.47-53
• /
• 2023

We propose a centralized passive-optical-network monitoring scheme using the resonance-spectrum properties of a Fabry-Perot cavity based on fiber Bragg gratings. Each cavity consists of two identical uniform fiber Bragg gratings and a varying cavity length or grating length, which can produce a unique single-mode resonance spectrum for the drop-fiber link. The output spectral properties of each cavity can be easily adjusted by the cavity length or the grating length. The resonance spectrum for each cavity is calculated by the transfer-matrix method. To obtain the peak wavelength of the resonance spectrum more accurately, the effective cavity length is introduced. Each drop fiber with a specific resonance spectrum distinguishes between the peak wavelength or linewidth. We also investigate parameters such as reflectivity and bandwidth, which determine the basic performance of the fiber Bragg grating used, and thus the output-spectrum properties of the Fabry-Perot cavity. The feasibility of the proposed scheme is verified using the Optisystem software for a simplified 1 × 8 passive optical network. The proposed scheme provides a simple, effective solution for passive-optical-network monitoring, especially for a high-density network with small end-user distance difference.

• Journal of the Optical Society of Korea
• /
• 제13권2호
• /
• pp.294-298
• /
• 2009

In this paper we proposed a new Bragg grating waveguide in order to improve reflectivity and to achieve compactness. Bragg gratings with various thicknesses were engraved in the middle of the core layer with a length of 3 mm. For the sake of cost-effectiveness, the $3^{rd}$ order Bragg grating waveguides were fabricated via conventional photolithography. The maximum reflectivities for the fixed width waveguide of $6{\mu}m$ with the 0.1 and $0.3{\mu}m$-thick Bragg gratings were, -13.14 and -6.25 dB, respectively, and the Bragg wavelengths were 1562.28, 1564.10 nm, respectively. A slight increase in the Bragg grating thickness can result in a remarkable reduction in the length of the Bragg grating waveguide with a fixed reflectivity.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.175-180
• /
• 1999

Generally, When we measure of object 3D surfaces with phase shifting shadow moire method, it is use of optical system consist of light source, grating, and ccd camera. At this time, it is important parameter that vertical distance of grating and camera, grating and light source, and horizontal distance of camera and light source. When use camera consist of complex lens vertical distance of grating and camera is unknown parameter. From this cause equivalent wave length of moire fringe is uncertain. In this study, We exactly obtain a vertical distance of grating and camera so improve on measurement accuracy.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.155-160
• /
• 2002

A new fabrication method of FBG sensor with gage length shorter than 10 mm is introduced using the reflection prism with special coating on the surface. It is verified that the bandwidth of FBG sensor increases exponentially as the gage length of it decreases. The transverse stress and strain gradient induced by local stress concentration which occurs during curing has an influence on the FBG sensor with gage length of 2 mm less than that of 10 mm.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.645-648
• /
• 2005

Microscopy has enabled the development of many advanced technologies, and higher level microscopic techniques are required according to the increase of research in nano-technology and bio-technology fields. Therefore, in many applications, we need to measure the dimension of micro-scale parts accurately, not just to observe their shapes. To establish the meter-traceability in microscopy, gratings have been widely used as a magnification standard. KRISS provides the certification service of magnification standards using an optical diffractometer and a metrological AFM (MAFM). They are based on different measurement principles, and so can give complementary information for each other. In this paper, we describe the configuration of each system and measurement procedures to certificate grating pitch values of magnification standards. Several measurement results are presented, and the discussion about them are also given. Using the optical diffractometer, we can calibrate a grating specimen with uncertainty of less than 50 pm. The MAFM can measure a grating specimen of down to 100 nm pitch value, and the calibrated values usually have uncertainty less than 500 pm.

• 한국인터넷방송통신학회논문지
• /
• 제19권5호
• /
• pp.175-180
• /
• 2019

새로운 고유치 문제에 기초한 모드 전송선로 이론 (Modal Transmission-Line Theory: MTLT))을 이용하여 blazed 격자 구조형 방향성 결합기 (B-GADC)의 광학 특성과 채널사이의 전력전달을 자세하게 분석하였다. 설계한 B-GADC의 결함효율을 분석하기 위하여 격자주기와 파장에 따라 변하는 quasi-TE 모드와 quasi-TM 모드의 분산곡선을 수치 해석하였으며, blazing 특성이 GADC의 결합효율에 미치는 영향을 분석하기 위하여 대칭형, 톱니형 그리고 비대칭형 blazed 격자구조를 설계하고 평가하였다. 수치해석 결과, blazed 격자구조가 대칭형에서 비대칭형으로 변함에 따라 최대 전력전송을 위한 최소 간격 조건을 만족하는 격자주기는 줄어들었으며 결합길이는 반대로 늘어나는 것을 확인하였다.

• 한국안광학회지
• /
• 제5권2호
• /
• pp.181-186
• /
• 2000

광속의 수렴 발산을 판단하기 위하여 무아레 무늬 발생기(moir$\acute{e}$ deflectometry)를 가상격자를 사용하는 제작하였다. 광원으로 He-Ne laser(3mW)와 무아레 무늬 발생기 광학계 중 광속확대기를 구성하기 위하여 제1렌즈와 제2렌즈의 초점거리는 각각 18 mm, 250 mm인 것을 사용하였다. 가상격자(virtual grating)를 발생시키기 위하여 회절격자(격자상수=$1.6{\mu}m/line$)와 전면 평반사경을 결합하여 무아레 무늬 발생기를 제작하였다. 광학계를 사용하여 시험렌즈의 유효초점거리를 측정하였고, 이 측정값과 유도된 식에 의한 이론값을 비교하였다.

• 대한전자공학회논문지
• /
• 제19권6호
• /
• pp.55-61
• /
• 1982

집적 광학에서 응용되는, 주기가 거의 선형으로 변하는 도파로 격자 필터의 파장에 따른 응답을 격자의 길이가 유한함을 고려하여 수식적으로 구하였다. 이 필터가 광대역 필터로서 설계되는 보편적인 경우에 대해서는 관련된 포물주면 함수를 변수의 위상에 따라 점근 근사를 취함으로써 파장에 따른 응답을 간단한 함수들로써 나타냈다. 또한 구한 결파식들이 기존 근사식들을 특별한 경우로 포함하는 일반적인 식임을 보였다. 마지막으로, 수식적인 해에 의한 결과와 RunRe-Kutta 수치 계산법에 의한 정확한 해를 비교하여 서로 잘 일치함을 확인하였다. An analytic solution for the spectral response of linearly-chirped grating filter is derived, which takes the finite physical length of filter into account. In the usual case of broad-band linearly-chirped grating filter the analytic solution is expressed in terms of elementary functions, by approximating asymptotically the involved parabolic cylinder functions over different ranges of its argument. It is also shown that derived results are general enough to include previously-available approximations as particular cases, and that they agree well with the numerical solutions based upon the Runge-Kutta method.