• Geomechanics and Engineering
• /
• v.4 no.4
• /
• pp.281-294
• /
• 2012

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.4
• /
• pp.37-45
• /
• 2010

Salt cementation, a typical naturally-cemented phenomenon, may occur due to water evaporation under the change of climate. Capillary force may influence the distribution of cement in granular soils. This study addresses the effect of capillary force on salt cementation using five different techniques: cone penetration test, electrical conductivity measurement, photographic imaging technique, nondestructive imaging technique, and process monitoring by elastic wave. Glass beads modeling a particulate media was mixed with salt water and then dried in an oven to create the cementation condition. Experimental results show that salt cementation highly concentrates at the top of the small particle size specimens and at the middle or the bottom of the large particle specimens. The predicted capillary heights are similar to the locations of high salt concentration in the cemented specimens. Five suggested methods show that the behavior of salt-cemented granular media heavily depends on the capillary force.

• Economic and Environmental Geology
• /
• v.37 no.4
• /
• pp.383-389
• /
• 2004

Understanding flow pattern of water and solute in subsurface is essential for the reduction and prevention of contamination of soil and groundwater and for the investigation and remediation of contaminated site. The objective of this study is to examine the infiltration pattern in a soil developed from the Jurassic granite using (Brilliant Blue FCF $C_{37}H_{34}N_{2}Na_{2}O_{9}S_{3}$), the nonfluorescent and nontoxic food dye. All image processing was conducted using geographic image processing software, ER Mapper, Version 6.2. The dye coverage was determined by counting the stained pixels in the photographs (80${\times}$80cm, 80TEX>${\times}$5cm) for the vertical and horizontal view. A homogeneous matrix flow occurred in the A horizon with weak, medium granular structure and fingering at the interface of finer-textured A horizon and coarser-textured C horizon. Pegmatitic vein originated from the granite and plant root in C horizon induced preferential flow.

• Korean Journal of Soil Science and Fertilizer
• /
• v.27 no.4
• /
• pp.296-302
• /
• 1994

To alter the paddy field to upland, mole drainages were constructed under 30cm of the surface of(Jeon buk silt loam) which is not appropriate for cultivation of upland crops. Intervals of the moles were 50cm, 100cm and 150cm and diverted to upland for soybean cultivation. By construction of the mole drainage, about 75% to 45% of the rainfall was drained and the ground water level was maintained below 40cm. After a year of drainage, the blocky surface was changed to granular or nutty structure which is common in upland fields. Oxidation was progressed to the deep layer because of soil dryness. Soybean yield were increased by 11% to 22% in the mole drained plots, but wet injury was occurred in the nontreated check plot with relatively poor growth status.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.2
• /
• pp.191-203
• /
• 1992

This paper dealt with the statistical values including mean, standard deviation, variance and coefficient of variation for 14 soil parameters available of Lade's double work-hardening model in order to predict the behaviour of granular soil. 27 sets of all 14 parameters for Baekma river sand were determined by regression using raw data acquired from 12 isotropic compression tests and 9 triaxial compression tests with the variation of confining pressure of 1, 2, and $4kg/cm^2$ respectively 3 times performed during this study. The characteristics of each parameters were investigated. By determining the range of the upper and lower bound dependent on the increase and decrease of the standard deviation from mean value of parameters, sensitivity of all the parameters was scrutinized, by which in turn the influence of experimental error generated inevitably during tests on the determination of soil parameters was also examined.

• Journal of Bio-Environment Control
• /
• v.11 no.4
• /
• pp.199-204
• /
• 2002

To overcome a decrease of Korean ginseng production caused by successive cropping, we have tried to develop a nutrient culture system for Korean ginseng production. For determining the optimal substrate, mixture of sand and TKS-2 (S＋T), peatmoss (P), reused rockwool (RR), and granular rockwool (GR) were investigated. The overall physico-chemical properties of RR fell into the reported optimal range for the ginseng cultivation. However, bulk density of S＋T was a little higher than that of soil in Korean ginseng fields. The top fresh weight of the ginseng was high in RR and S＋T substrates. The root fresh and dry weights in the RR were remarkably greater than that in the conventional soil (CS) of Korean ginseng fields. In terms of ginseng quality, the vitamin C content of ginseng root in nutrient culture was higher than that in CS. However, the contents of crude saponin and total ginsenosides in ginseng between in the nutrient culture and in the soil culture did not show any significant differences.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.8
• /
• pp.13-24
• /
• 2014

A series of trapdoor model tests was systematically performed in order to investigate soil arching. The mobilized soil arching was clearly observed by change of the vertical earth pressure loaded on trapdoor of soil container box. A slow decent of the loading plate at the trapdoor results in loosening zone over the trapdoor and the stress in this loosening zone was transferred to the stationary zone in the vicinity of the trapdoor. In particular, it was observed that the vertical earth pressure rapidly decreased in the loosening zone and increased in the stationary zone at the trapdoor. Both the maximum decreasing rate of the vertical earth pressure in the loosening zone and the increasing rate of the vertical earth pressure in the stationary zone were not influenced by the ground density, but affected by the size of the trapdoor. The loosening zone could be defined by the elliptical configuration, in which the major axis was twice as long as the height of the loosening zone at the center of trapdoor and the minor axis was the same as the width of trapdoor. The height of loosening zone at the center of trapdoor was one and a half times as long as the width of trapdoor loading plate.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.3
• /
• pp.53-58
• /
• 2012

In general, sand compaction pile(SCP) method and gravel compaction pile(GCP) method have been mainly used to reinforce soft soils such as soft clay or loose sandy ground. But the sand compaction pile method has problems such as lack of sand supply and destroying the nature while collecting sand, the gravel compaction pile method has a problem such as decreased permeability of the drainage material due to clogging. Recently, the study to replace sand with bottom ash which has similar engineering properties with sand is in active. As a fundamental research on bottom ash mixture compaction pile utilizing bottom ash, its behavioral characteristics depending on granular materials and replacement ratio has been simulated numerically. In particular, Settlement Reduction Ratio(SRR) according to the distance from the center of pile was calculated. The main findings were as follows. Change values of Mixture Compaction Pile's SRR according to granular materials showed similar patterns and stiffness of the composite soil is increased depending on the replacement ratio so SRR showed decreased patterns. Especially, when the replacement ratio is in 20~40%, it increase significantly. When the replacement ratio is over 40%, it increase slowly. When considering the economics, 30~40% replacement ratio is appropriate.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.22 no.2
• /
• pp.121-127
• /
• 1977

Leaf burning due to nitrofenapplication was characterized as brown color spot appearing on the leaf sheath and blade. The spots predominantly appeared around 5-7 cm high above soil surface regardless of different particle size, formulation, application method, or water level. Magnitude and frequency of burn spots increased somewhat as the granular size gets finer, by higher water level, or in transplanted rice compared to directly sown rice when applied at 7 leaf-stage, but there was no indication of increase in leaf burning due to clinging of floating dust to rice plant. When collections from local distributor's stock of TOK 7G, a granular formulation of nitrofen, were analyzed for particle size composition, 98.9% by weight ranged between 9 to 35 meshes, and only about 0.08% by weight was of particles finer than 100 mesh.

• The Journal of Engineering Geology
• /
• v.26 no.4
• /
• pp.485-495
• /
• 2016

To reinforce and improve the soft ground under a breakwater while using materials efficiently, the replacement ratio and leaving periods of surcharge load are optimized probabilistically. The results of Bayesian updating of the random variables using prior information decrease uncertainty by up to 39.8%, and using prior information with more samples results in a sharp decrease in uncertainty. Replacement ratios of 15%-40% are analyzed using First Order Reliability Method and Monte Carlo simulation to optimize the replacement ratio. The results show that replacement ratios of 20% and 25% are acceptable at the column jet grouting area and the granular compaction pile area, respectively. Life cycle costs are also compared to optimize the replacement ratios within allowable ranges. The results show that a range of 20%-30% is the most economical during the total life cycle. This means that initial construction cost, maintenance cost and failure loss cost are minimized during total life cycle. Probabilistic analysis for leaving periods of shows that three months acceptable. Design optimization with respect to life cycle cost is important to minimize maintenance costs and retain the performance of the structures for the required period. Therefore, more case studies that consider the maintenance costs of soil structures are necessary to establish relevant design codes.