• Journal of Biosystems Engineering
• /
• v.25 no.6
• /
• pp.503-510
• /
• 2000

To improve the milling condition of brown rice a continuous type conditioning equipment was developed. To validate the performance of this machine the experimental operation was done at Sa-cheon RPC(Rice Processing Complex) using short grain rough. The initial moisture contents of brown rice were 15.0∼16.5%(w.b) and the flow rate of brown rice passing through the conditioner were 4,370kg per hour. The moisture content differences of brown rice between conditioned and non-conditioned were showed within 0.5%(w.b) This results means that the water injected to brown rice were absorbed to the surface of brown rice evenly. The moisture contents of conditioned treated milled rice were showed slightly higher than that of non-conditioned ones but it was considered that the conditioning process did not affected the weight increasing of milled rice by water supply. For initial moisture contents of 15.0∼16.5%(wb) brown rice it was found that the proper water supply rate was 0.115(cc-water)/(kg·%-brown rice) and the increments of whole rice were 2.2% compared to the non-conditioned ones. it was considered that the conditioning process did not influenced the whiteness of milled rice because the whiteness differences between conditioned and non-conditioned milled rice were negligible. About 18% of electric power which drives the abrasive type rice milling machine was saved at 0.115(cc-water)/(kg·%-brown rice) of water supply rate.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.45-51
• /
• 1999

The semi-solid forging is a new forging technology in which the billet is heated to the semi-solid state coexisting liquid and solid phase for making globular microstructure and subsequently formed. As the semi-solid forging is compared with conventional casting such as die casting and squeeze casting for the characteristics of its process, the product without inner defects such as gas porosity and segregation can be obtained and its microstructure is globular grain. Simutaneously, its mechanical properties are improved by globular microstructure and the lower temperature of the slug causes the cycle time of manufacturing to be shortened and the die life to be lengthened. As it is compared with conventional cold and hot forging, it is possible to minimize the equipment of production owing to a lower forming load and reduce the number of process by a followed treatment for complex shaped product. Therefore it is needed to confirm the quality of a semi-solid forged product by defining its characteristics quantitatively under these advantages. This paper investigates the formability of a master cylinder by its forming variables. And the microstructural characteristics and mechanical property of it is also studied.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.90-93
• /
• 2002

The sintering process of BSCCO 2223 tapes is a complex process that is very sensitive to parameters, such as temperature, oxygen partial pressure, heating and cooling rate and holding time. During the first heat treatment, 2212 phase of precursor powder is partially transformed into 2223 phase and some residual secondary phases, such as $(Bi,Pb)_2$$Sr_2$CuO／sub y／(2201), $(Ca,Sr)_2$CuO／sub y／(2/1AEC), (Ca,Sr)／sub 14／Cu／sub 24／O／sub 41／(14／24 AEC) etc. The secondary phases are difficult to be removed from the BSCCO 2223 matrix on the heat treatment. These secondary phases degrade the critical current density. In order to minimize the amount and size of alkaline earth cuprate(AEC) particles step heat treatment is applied during the first heat treatment under the varying atmosphere. Experimental results showed that by adapting the step heat treatment process, the amount and particle size of the secondary phases in the final tapes are decreased. Consequently, the BSCCO 2223grain texture and Jc properties are improved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.75-81
• /
• 2003

This study evaporates ZnO layer thickness differently with RF sputtering method on Si Wafer(n-100). This study is performed to examine the characteristics of photon energy and dielectric loss according to the thickness of ZnO and increase the reliability and reproduction of ZnO thin film. It is confirmed that the variation of electric Permittivity by frequency is resulted from the formation of particles within thin film, the particle size and the polarization on grain boundary. Peak of electric Permittivity value of thin film has slower and less value in early low wavelength by the coulomb force involved in carrier combination according to the increase of frequency. Reversal of electric Permittivity values is induced by dipole polarization shown in the dielectric of thin film. Complex electric constant $({\varepsilon}_1{\varepsilon}_2)$ has larger peak values as it’s thickness is thinner and then it is larger according to the increase of frequency. Electric Permittivity by photon energy has large value in imaginary number and is reduced exponentially by the increase of carrier density according to that of photon energy.

• Journal of the Korean Ceramic Society
• /
• v.34 no.8
• /
• pp.897-907
• /
• 1997

Thin films of Bi4-xSmxTi3O12(0$\leq$x$\leq$2) were prepared on Pt/Ti/SiO2/Si(100) at $700^{\circ}C$ using spin-coating with sols derived from Bi-Sm-Ti complex alkoxides. From X-ray diffraction analysis, it was observed that Sm-substituted phases resembled ferroelectric Bi4Ti3O12 in structure. Variations of their lattice parameters depending on the amount of Sm-substitution showed that an anomalous structural distortion might exist at x=1. The grain sizes of the thin films decreased from 0.115 ${\mu}{\textrm}{m}$ to 0.078${\mu}{\textrm}{m}$ with increasing the amount of Sm-substitution. The dielectric constants and the remanent polarizations of the thin films decreased with increasing the amount of the Sm-substitution, which were related to decrease of the stereo-active Bi3+ ion contributing to polarization. However, these values were exceptionally high at x=1, compared to those of the other substituted phases. Such an anomaly suggests that the phase of x=1 has 1:1 chemical ordering between Sm and Bi in structure. The thin films of all compositions except x=2 showed ferroelectricity. The thin film of x=2 was paraelectric, whose grains were too fine to exhibit ferroelectricity.

• Corrosion Science and Technology
• /
• v.7 no.3
• /
• pp.182-186
• /
• 2008

The microstructures of the oxide scale developed at high temperature on steels are very complex and their development depends on many factors including time, temperature, oxidation conditions and alloying elements. The classical model of an oxide scale on steel consisting of wüstite, magnetite and haematite layers, is more complicated in reality and its properties change with the factors that affect their development. An understanding of the oxide scale formation and its properties can only be achieved by careful examination of the scale microstructure. The oxide scale microstructure may be difficult to characterise by conventional techniques such as optical or standard scanning electron microscopy. An unambiguous characterisation of the scale and the correct identification of the phases within the scale are difficult unless the crystallographic structure for each phase in the scale is considered and a simultaneous microstructure-microtexture analysis is carried out. In the current study Electron Backscatter Diffraction (EBSD) has been used to investigate the microstructure of iron oxide layers grown on low carbon steels at different times and temperatures. EBSD has proved to be a powerful technique for identifying the individual phases in the oxide scale accurately. The results show that different grain shapes and sizes develop for each phase in the scale depending on time and temperature.

• Nuclear Engineering and Technology
• /
• v.46 no.6
• /
• pp.857-862
• /
• 2014

Mechanical alloying under various gas atmospheres such as Ar, an Ar-$H_2$ mixture, and He gases were carried out, and its effects on the powder properties, microstructure and mechanical properties of ODS ferritic steels were investigated. Hot isostatic pressing and hot rolling processes were employed to consolidate the ODS steel plates. While the mechanical alloyed powder in He had a high oxygen concentration, a milling in Ar showed fine particle diameters with comparably low oxygen concentration. The microstructural observation revealed that low oxygen concentration contributed to the formation of fine grains and homogeneous oxide particle distribution by the Y-Ti-O complex oxides. A milling in Ar was sufficient to lower the oxygen concentration, and this led a high tensile strength and fracture elongation at a high temperature. It is concluded that the mechanical alloying atmosphere affects oxygen concentration as well as powder particle properties. This leads to a homogeneous grain and oxide particle distribution with excellent creep strength at high temperature.

• Korean Journal of Materials Research
• /
• v.13 no.4
• /
• pp.228-232
• /
• 2003

The effects of$ Nd_2$$O_3$addition on the properties of Mn-Zn ferrite were investigated in the doping concentration range from 0.05 to 0.25 wt%. All samples were prepared by standard fabrication of ferrite ceramics. With increasing the Neodymium oxides, specific density and initial permeability increased on the whole. But, the tendencies such as upper result had the measured value on limitation and characteristics saturated or decreased properties after that. With increasing the content of Neodymium oxides. both the real and imaginary component of complex permeability and the magnetic loss(tan$\delta$) increased. Because reason that magnetic loss increases is high ratio that a real department increases than imaginary department. Magnetic loss increased none the less for increasing the real department related with magnetic permeability. But, the magnetic loss of ferrite doped with the Neodymium oxides were lower than that of none doped Mn-Zn ferrite. The small amount of percent Neodymium oxides in Mn-Zn ferrite composition led to enhancement of resistivity in bulk, and more so in the grain boundary.

• Journal of Surface Science and Engineering
• /
• v.26 no.2
• /
• pp.63-70
• /
• 1993

The mechanical properties of ferrite-martensited dual phases steels are affected by the microstructural factors, such as martensited volume fractions, ferrite grain size, strength ratio, connectivity, etc. Two phase alloys are technologically important. However, there is a lack of understanding as to stress-strain behavior of dual phase alloy in terms of stress-strain behavior of each component phases. The lack of the understanding stems from the complex deformation behavior of two phase alloys. The aim of this study is to rationalize stress-strain behavior of dual phase alloy in terms of the stress-strain behavior of component phase by systematically considering all the factors listed above. It was found that for a given martensite volume fraction, the calculated stress-strain curve was higher for a finer particles size than for a coarse particle sized within the range of the strains considered, and this behavior was seen for all the different volume fraction alloys considered. The calculated stress-strain curves were compared with corresponding experimental curves, and in general, good agreement was found. The maximum difference in flow stress between the calculated and the experimental results occurs at the nearly beginning of the plastic deformation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.259-262
• /
• 1999

In this study, we investigated magnetic Properties of N $i_{0.2-x}$C $u_{x}$Z $n_{0.305}$F $e_{0.495}$ (x=0 ~0.2) ferrites. As the increased, the density and shrinkage increased until 5.3g/㎤, 20% respects, but the absorption decreased rate until 0.01%. As a results of the density, absorption rate, and shrinkage rate, the grain growth progressed rapidly in x=0.125 at 105$0^{\circ}C$, x=0.075 at 115$0^{\circ}C$, and x=0.025 at 115$0^{\circ}C$ for 3hours. As the CuO concentration increased, initial permeability increased at sintered 105$0^{\circ}C$ and 115$0^{\circ}C$ for 3 hours, but decreased at 125$0^{\circ}C$ for 3 hoers. The complex permeability as a function of frequency were high values at sintered 105$0^{\circ}C$ for 3 hours in x=0.005, 0.075.5.5.5.