• Progress in Superconductivity and Cryogenics
• /
• v.22 no.2
• /
• pp.12-16
• /
• 2020

Circulating cooling systems consume a lot of water, and most of the water from river, which contains a large amount of Ca2+, Mg2+, et al, and has the characteristics of high hardness and large turbidity. The water can form scale on the surface of the heat exchanger and the pipes, which would reduce the heat transfer efficiency and affect the heat exchanger's length of service. In this study, the Superconducting High Gradient Magnetic Separation (S-HGMS) technology was used in river water treatment and the effects of agent A, agent B, and S-HGMS on the removal of hardness and turbidity were discussed. The results showed that the hardness removal rate reached 71.3% and the turbidity was decreased to 0.5 NTU.

• Journal of the Korean Ceramic Society
• /
• v.23 no.2
• /
• pp.13-20
• /
• 1986

Composite polycrystals including ${\gamma}$-$6Bi_2O_3$.$SiO_2$ crystal which have needlelike regular structure are useful for the high resolution optical devices. For the purpose of obtaining the composite polycrystals described above the melts of eutectic composition in the three eutectic systems including $6Bi_2O_3$.$SiO_2$ composition were unidirectionally solidified at a rate of 0.05 and 0.25 cm/h under a thermal gradient of 10$0^{\circ}C$/m. Composite polycrystals of relatively regular structure in which needlelike ${\gamma}$-$6Bi_2O_3$.$SiO_2$ crystals were arrayed in parallel with $2Bi_2O_3$.$B_2O_3$ crystal matrix were obtained when the eutectic melt of $6Bi_2O_3$.$SiO_2 -2Bi_2O_3$.$B_2O_3$ system was solidified at a rate of 0.25 cm/h. Partial structural irregularity however was found in the obtained composite polycrystals.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.10
• /
• pp.1293-1302
• /
• 1999

In this paper, an on-line process scheme is presented for implementation of a intelligent on-line modeling of nonlinear complex system. The proposed on-line process scheme is composed of FNN-based model algorithm and PLC-based simulator, Here, an adaptive fuzzy-neural networks and HCM(Hard C-Means) clustering method are used as an intelligent identification algorithm for on-line modeling. The adaptive fuzzy-neural networks consists of two distinct modifiable sturctures such as the premise and the consequence part. The parameters of two structures are adapted by a combined hybrid learning algorithm of gradient decent method and least square method. Also we design an interface S/W between PLC(Proguammable Logic Controller) and main PC computer, and construct a monitoring and control simulator for real process system. Accordingly the on-line identification algorithm and interface S/W are used to obtain the on-line FNN model structure and to accomplish the on-line modeling. And using some I/O data gathered partly in the field(plant), computer simulation is carried out to evaluate the performance of FNN model structure generated by the on-line identification algorithm. This simulation results show that the proposed technique can produce the optimal fuzzy model with higher accuracy and feasibility than other works achieved previously.

• Journal of Broadcast Engineering
• /
• v.20 no.3
• /
• pp.440-448
• /
• 2015

A pedestrian collision warning system which makes a judgement of pedestrian's intention to help avoiding hitting accidents is proposed. This system uses the image sequences obtained from a car black box as well as vehicle's speed obtained from a GPS. It detects pedestrians, if any, based on the Histogram of Gradient method and extracts several information such as the pedestrian's relative positions, the direction of motion vectors, and distance between vehicle and pedestrian . A fuzzy logic based on these extracted information is applied to analyze the pedestrian's safety levels. When the safety level is determined to be danger, an alarm is triggered to the driver. The performance of the proposed algorithm is tested under various driving scenarios, which shows it works successfully in real-time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.10
• /
• pp.3038-3047
• /
• 1996

In telerobot systems, visual servoing of a task object for a slave arm with an eye-in-hand has drawn an interesting attention. As such a task ingenerally conducted in an unstructured environment, it is very difficult to define the inverse feature Jacobian matrix. To overcome this difficulty, this paper proposes an auto-tuning fuzzy rule-based visual servo algorithm. In this algorithm, a visual servo controller composed of fuzzy rules, receives feature errors as inputs and generates the change of have position as outputs. The fuzzy rules are tuned by using steepest gradient method of the cost function, which is defined as a quadratic function of feature errors. Since the fuzzy rules are tuned automatically, this method can be applied to the visual servoing of a slave arm in real time. The effctiveness of the proposed algorithm is verified through a series of simulations and experiments. The results show that through the learning procedure, the slave arm and track object in real time with reasonable accuracy.

• Journal of Korea Foundry Society
• /
• v.8 no.4
• /
• pp.437-445
• /
• 1988

The effect of interlamellar spacing on microstructural stability at high temperature was studied for unidirectionally solidified ternary $Ni\;/\;Ni_3Al-Ni_3$ Nb and binary $Ni-Ni_3Nb$ eutectic composite. The interlamellar spacing of both alloy systems were varied with the growth rate according to $"{\lambda}^2R=constant"$ relationship. As a result of isothermal heat treatments at high temperature it was considered that coarsening of lamellar structure was due to concentration gradient between the tip with a relatively small radius of curvature and the side of the thick lamellae with a larger radius of the opposite sign. Fault density was increased as the interlamellar spacing decreased. Therefore it is also considered that the higher coarsening rate of the specimen with the smaller interlamellar spacing was due to higher fault density. And the diference of coarsening rate between $Ni\;/\;Ni_3Al-Ni_3Nb$ and $Ni-Ni_3Nb$ eutectic composites was not observed when the interlamellar spacing was similar in size. This means that the presence of ${\gamma}'$ in ${\gamma}\;/\;{\gamma}'\;-{\delta}$ eutectic had no b arrier effect to diffusion through the ${\gamma}$ matrix.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.64-71
• /
• 2012

An efficient cooling system is an essential part of the electronic packaging such as a high-luminance LED lighting. A special technology, Pulsating Heat Pipe (PHP), can be applied to improve cooling of a sealed, explosion-proof LED light fixture. In this paper, the characteristics of the pulsating heat pipes in the imposed thermal boundary conditions of LED lightings were experimentally investigated and a PHP device that works free of alignment angle was investigated for cooling of explosion-proof LED lights. Five working fluids of ethanol, FC-72, R-123, water, and acetone were chosen for comparison. The experimental pulsating heat pipe was made of copper tubes of internal diameter of 2.1 mm, 26 turns. A variable heat source of electric heater and an array of cooling fins were attached to the pulsating heat pipe. For the alignment of the heating part at bottom, an optimum charging ratio (liquid fluid volume to total volume) was about 50% for most of the fluids and water showed the highest heat transfer performance. For the alignment of the heating part on top, however, only R-123 worked in an un-looped construction. This unique advantage of R-123 is attributed to its high vapor pressure gradient. Applying these findings, a cooling device for an explosion-proof type of LED light rated 30 W was constructed and tested successfully.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.3
• /
• pp.1159-1181
• /
• 2016

This study introduces an image-based 2D-to-3D conversion system that provides significant stereoscopic visual effects for humans. The linear and atmospheric perspective cues that compensate each other are employed to estimate depth information. Rather than retrieving a precise depth value for pixels from the depth cues, a direction angle of the image is estimated and then the depth gradient, in accordance with the direction angle, is integrated with superpixels to obtain the depth map. However, stereoscopic effects of synthesized views obtained from this depth map are limited and dissatisfy viewers. To obtain impressive visual effects, the viewer's main focus is considered, and thus salient object detection is performed to explore the significance region for visual attention. Then, the depth map is refined by locally modifying the depth values within the significance region. The refinement process not only maintains global depth consistency by correcting non-uniform depth values but also enhances the visual stereoscopic effect. Experimental results show that in subjective evaluation, the subjectively evaluated degree of satisfaction with the proposed method is approximately 7% greater than both existing commercial conversion software and state-of-the-art approach.

• Smart Structures and Systems
• /
• v.18 no.5
• /
• pp.1029-1062
• /
• 2016

In this research, the nonlinear free vibration analysis of boron-nitride micro ribbon (BNMR) on the Pasternak elastic foundation under electrical, mechanical and thermal loadings using modified strain gradient theory (MSGT) is studied. Employing the von $K{\acute{a}}rm{\acute{a}}n$ nonlinear geometry theory, the nonlinear equations of motion for the graphene micro ribbon (GMR) using Euler-Bernoulli beam model with considering attached mass and size effects based on Hamilton's principle is obtained. These equations are converted into the nonlinear ordinary differential equations by elimination of the time variable using Kantorovich time-averaging method. To determine nonlinear frequency of GMR under various boundary conditions, and considering mass effect, differential quadrature element method (DQEM) is used. Based on modified strain MSGT, the results of the current model are compared with the obtained results by classical and modified couple stress theories (CT and MCST). Furthermore, the effect of various parameters such as material length scale parameter, attached mass, temperature change, piezoelectric coefficient, two parameters of elastic foundations on the natural frequencies of BNMR is investigated. The results show that for all boundary conditions, by increasing the mass intensity in a fixed position, the linear and nonlinear natural frequency of the GMR reduces. In addition, with increasing of material length scale parameter, the frequency ratio decreases. This results can be used to design and control nano/micro devices and nano electronics to avoid resonance phenomenon.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1143-1148
• /
• 2005

Experimental results for heat transfer characteristic and pressure gradient of HCs refrigerants R-290, R-600a, R-1270 and HCFC refrigerant R-22 during condensing inside horizontal double pipe heat exchangers are presented. The test sections which have one tube diameter of 12.70 mm with 0.86 mm wall thickness, another tube diameter of 9.52 mm with 0.76 mm wall thickness are used for this investigation. The local condensing heat transfer coefficients of hydrocarbon refrigerants were higher than those of R-22. The average condensing heat transfer coefficient increased with the increase of the mass flux. It showed the higher values in hydrocarbon refrigerants than R-22. Hydrocarbon refrigerants have higher pressure drop than those of R-22 in 12.7 mm and 9.52 mm. This results from the investigation can be used in the design of heat transfer exchangers using hydrocarbons as the refrigerant for the air-conditioning systems.