• 한국응용과학기술학회지
• /
• 제21권4호
• /
• pp.335-344
• /
• 2004

In this work, the properties as polishing wax for automobile of O/W type microemulsion containing wax, liquid paraffine and quaternaryammonium salt was investigated. The microemulsions were prepared at $96{\sim}97^{\circ}C$ by the phase inversion method, and polyoxyethylene(20) sorbitan monooleate (POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C) as the emulsifiers were used. The mean particle size of the rnicroemulsions was about 7${\pm}$0.5nm and as the properties of polishing wax, gloss increased degree, water resistant gloss degree, initial and final contact angle after water resistance were tested. The result was that the value of water resistantance and contact angle were decreased with increasing amount of POE(20)SMO and D.D.A.C., while the gloss degree values did not affected. And the rnicroemulsion blended with mono ethylene glycol(MEG) of 5${\sim}$15wt% showed smaller particle size and more stable particle size distribution than without MEG. Finally, this microemulsion showed more excellent values of gloss degree, the water resistant gloss degree and contact angle, than two kinds of commercial polishing wax for automobile.

• 대한치과의료관리학회지
• /
• 제11권1호
• /
• pp.38-46
• /
• 2023

Composite resins, commonly used in clinical practice, have been developed to improve aesthetics to obtain smooth surfaces. Although the restored composite resin has a smooth surface, it gradually becomes rough over time. Therefore, this study measured glossiness to evaluate the surface of various composite resins and attempted to evaluate the maintenance of glossiness of composite resins by observing surfaces that change to roughness. Specimens were produced using resin used in clinical practice: Gradia direct anterior (GA), Tetric N-Ceram (TN), Ceram.X Sphere TEC one (CX), Filtek Z350XT (FT), Estelite sigma quick (ES). After creating a smooth surface with slide glass, five locations were randomly selected to measure surface gloss, and the average was the representative value of the specimen. Roughness was applied to the specimen under water pouring at the same speed and pressure using SiC paper #2400, 1200, and 400. The gloss unit of different SiC papers was measured. To evaluate the gloss unit and gloss retention between composite resins, one-way analysis of variance and Tukey multiple comparisons test were used. As a result of the study, there was a difference in gloss unit of specimens produced under the same conditions. Although the degree differed depending on the composite resin, there was also a difference in gloss retention. Based on the findings, composite resins show differences in gloss due to their different characteristics. Ceram.X Sphere TEC one (CX) showing the lowest gloss retention and Estelite sigma quick (ES) showing the highest.

• 펄프종이기술
• /
• 제30권3호
• /
• pp.74-83
• /
• 1998

The phenomenon of decrease in sizing efficiency when the stock temperature is increased is well recognized as summer sizing, and this is believed to be caused by uneven distribution of sizing agents on paper surface most often incurred by coagulation of sizing agents. When unevenly sized paper is used as coating base stock, nonuniform consolidation of the coating layer may result, which, in turn, causes uneven distribution of binder on coating surface. This causes nonuniform ink absorption to produce print mottle. In this study the effects of simple or polymeric electrolytes, storage temperature and time on the coagulation of cationic dispersed rosin size were investigated using a turbidity measurement method which was verified to correlate well with the particle size of rosin emulsion or its coagulates. Handsheets sized with rosin dispersions coagulated under various conditions were prepared and their sizing degree and coated paper properties including gloss and ink density were examined. The relationship between the sizing nonuniformity of coated papers and its ink absorption property was evaluated. Turbidity of rosin emulsion increased as the storage temperature and time were increased. Addition of simple or polymeric electrolytes caused reduction in $zeta$ -potential of the rosin dispersion and accelerated the coagulation tendency substantially. Reversion of the $zeta$ -potential of rosin dispersion, however, did not occur when coagulation was induced with simple electrolytes. On the other hand, addition of an anionic polyelectrolyte reversed the $zeta$ -potential of the flocculated rosin dispersion. This indicated that electrical double layer compaction and bridging flocculation were coagulation mechanisms for simple and polymeric electrolytes, respectively. Sizing degree decreased as coagulation of rosin was increased. Paper gloss, ink gloss and ink density were increased when sizing degree of base stock was increased most probably due to prevention of base paper swelling and increased binder migration to coating surface. This suggested that uneven printing ink density occurred when uneven sizing development was induced by coagulation of rosin particles.

• 한국의류학회지
• /
• 제33권1호
• /
• pp.149-159
• /
• 2009

The purposes of this study are to evaluate physical performance of metallic Jacquard fabrics, and to contribute to the research and development of the women's suit made of the metallic Jacquard fabrics. First, eight fabrics were woven with two kinds of warp yarns(nylon and rayon) and weft yarn blended with various contents(0, 7, 14, 21%) of metallic yarn. Second, the mechanical properties were measured by using the KES-FB system, and physical properties such as tensile strength, tearing strength, abrasion resistance, drape, pilling, snagging, degree of crease resistance, flexural stiffness, specular gloss, folding endurance and electrostatic propensity were measured. The results were as follows. As the metal fiber content increased, bending, shear, thickness and weight increased, which imply low recovery of wrinkles. It means that metallic Jacquard fabrics enable to use as a memory fabric. 7% metallic Jacquard fabric showed a low value at total hand value, but there was little change. As the metal fiber content increased, tensile strength, tearing strength, drape coefficient, specular gloss and flexural stiffness increased, however the degree of crease resistance, electrostatic propensity and folding endurance decreased. The metallic Jacquard fabrics were excellent in snagging, abrasion resistance and pilling.

• Nano
• /
• 제13권12호
• /
• pp.1850137.1-1850137.9
• /
• 2018

A series of silica surface-capped with hexamethyldisilazane (denoted as $H-SiO_2$) were prepared by liquid-phase in-situ surface-modification method. The as-obtained $H-SiO_2$ was incorporated into acrylic amino (AA) baking paint to obtain AA/$H-SiO_2$ composite extinction paints and/or coatings. $N_2$ adsorption-desorption tests were conducted to determine the specific surface area as well as pore size and pore volume of $H-SiO_2$. Moreover, the effects of $H-SiO_2$ matting agents on the physical properties of AA paint as well as the gloss and transmittance of AA-based composite extinction coatings were investigated. Results show that $H-SiO_2$ matting agents possess a large specific surface area and pore volume than previously reported silica obtained by liquid-phase method. Besides, they have better dispersibility in AA baking paint than the unmodified silica. Particularly, $H-SiO_2$ with a silica particle size of $6.7{\mu}m$ and the dosage of 4% (mass fraction) provides an extinction rate of 95.2% and a transmittance of 79.3% for the AA-based composite extinction coating, showing advantages over OK520, a conventional silica matting agent. Along with the increase in the silica particle size, $H-SiO_2$ matting agents cause a certain degree of increase in the viscosity of AA paint as well as a noticeable decrease in the gloss of the AA-based composite extinction coating, but they have insignificant effects on the hardness and adhesion to substrate of the AA-based composite coatings. This means that $H-SiO_2$ matting agents could be well applicable to preparing low-viscosity and low-gloss AA-based matte coatings.

• 펄프종이기술
• /
• 제39권5호
• /
• pp.26-31
• /
• 2007

Hanji is a traditional Korean handmade paper, which has been known in ancient Far East as excellent quality calligraphic paper for more than 1,500 year. Hanji is mostly made of Korean paper mulberry bast fibers, and if properly processed, normally lasts for more than 1,000 years with significant strength and still recognizable calligraphic writings or drawings on it. Dochim is a special way of Hanji calendering process, but is turned out to be quite different from modern calendering (machine calendering) in several aspects. In Dochim process, mechanical impacts were applied vertically to the surface of papers. Compared to the modern calendering, Dochim increased paper gloss much more, but paper smoothness a little less. By the Dochim process, densification occurred and the degree of densification was more sensitive to the fiber type in the Dochim process than in the calendering method.

• 한국화재소방학회논문지
• /
• 제23권5호
• /
• pp.78-83
• /
• 2009

방염도료의 주성분 및 특성에 따른 방염성능과 발연특성에 대하여 알아보기 위하여 국내에 유통되어지는 17종의 방염도료를 MDF에 방염처리하여 45도 연소실험과 연기밀도실험을 실시하였다. 45도 연소실험 결과 주성분별로는 아크릴 수지를 주성분으로 한 방염도료의 방염성능이 가장 우수한 것으로 평가되어지며 유성방염도료 보다는 수성방염도료의 방염성능이 우수한 것으로 나타났고 또한 무광방염도료보다 유광방염도료의 방염성능이 더 우수한 것으로 평가되었다. 연기밀도실험을 통한 발연특성은 아크릴 수지를 주성분으로 한 시료에서 연기밀도가 상대적으로 낮게 측정되었으며 특성별로는 수성방염도료를 처리한 시료들에서 유성방염도료를 칠한 시료보다 연기밀도가 낮게 측정되었다.

• 한국응용과학기술학회지
• /
• 제28권1호
• /
• pp.35-47
• /
• 2011

For the synthesis of water soluble acrylic modified epoxyester resin, fatty acid/epoxy ratio of 50/50 was used, and introduced maleic anhydride. Ratio of styrene/acrylic acid of acrylic monomers was fixed 85/15 and ratio of epoxyester/acrylic monomer was controlled 80/20, 75/25, 70/30, 65/35, and degree of neutralization were changed 65%, 80%, to 100%. As a result, 40% solids acrylic modified epoxyester resins were synthesized. Resins were evaluated water soluble stability, drying time, water resistant, storage stability and physical properties. And the white paints were prepared, and were evaluated viscosity, drying time, water resistance, adhesion, sagging, spray workability, gloss, salt spray resistance, skinning, whiteness and flash rust. As a result, the degree of neutralization of 100% and the ratio of epoxyester/acrylic monomer of 75/25 showed the best properties.

• 한국응용과학기술학회지
• /
• 제37권5호
• /
• pp.1298-1305
• /
• 2020

본 연구 목적은 밍크 오일로 손상된 모발의 개선 정도를 알아보고자 하였다. 실험방법으로 밍크오일 함량을 0 g, 1 g 2 g, 3 g 으로 모질 개선 제형제를 제조하였다. 제형제로 탈색한 시료 모발에 도포 전과 도포 후를 측정하여 비교 분석하였다. 모질 개선 효과를 알기 위해 인장강도, 메틸렌블루를 이용한 흡광도, 광택을 측정하였다. 실험결과는 인장강도 측정결과 건강모 보다는 실험군의 인장강도는 감소하였다. 7레벨에서의 인장강도는 밍크 오일 함량이 높을수록 증가하였다. 흡광도 측정결과 대조군 인 건강모 보다는 실험군 모두가 증가하였다. 대조군 인 0 g함유한 것보다 실험군 7레벨에서 1 g, 2 g, 3 g 도포한 시료의 흡광도 값은 밍크 함량이 높을수록 감소하였다. 광택 측정 결과는 건강모 보다는 실험군의 광택 값이 증가하고 7레벨에서의 광택 값은 함량이 증가할수록 감소하였다. 결론은 밍크 오일이 손상된 모발에 도포 시 모질 개선 효과가 있는 것을 알 수 있었다. 차후 모질 개선을 위한 다양한 오일 성분에 대한 연구가 필요하다.

• 한국응용과학기술학회지
• /
• 제38권1호
• /
• pp.9-18
• /
• 2021

본 연구는 인디고 염료로 모발에 도포하여 염색효과와 모질 특성 변화를 알아보고자 하였다. 연구방법은 인디고 염료를 중탕하여 사용하였다. 염료를 건강모와 탈색한 시료 모발에 도포 후 열처리와 자연방치 시간을 다르게 하였다. 측정은 시료별로 도포 전과 후를 측정하여 비교 분석하였다. 염색효과를 알기 위해 색차계를 이용하여 L⁎, a⁎, b⁎값과 물 빠짐을 측정하였다. 모질 변화를 알기 위해 인장강도, 메틸렌블루를 이용한 흡광도, 광택을 측정하였다. 결과는 염색효과 측정 결과 모든 시료에서 L⁎값, a⁎값, b⁎ 값의 도포 전과 후의 통계분석 결과는 유의미한 결과로 염색 효과가 있었다. 물 빠짐 측정결과는 1일차에는 가장 많이 빠졌고, 3일차부터는 더 이상의 물 빠짐이 없었다. 인장강도 측정결과는 모든 시료의 평균값은 증가하였다. 그러나 통계분석 결과 유의미하지 않은 결과로 모질의 특성 변화는 없었다. 메틸렌블루를 이용한 흡광도 분석결과 건강7L(3)을 제외 한 시료에서 통계분석 결과 모질의 특성 변화는 없었다. 광택측정결과는 통계분석 결과 광택에 변화를 주는 것을 알 수 있었다. 결론은 인디고 염료에 의한 모발 염색효과가 있었고, 모질의 특성 변화는 광택은 있고, 인장강도와 흡광도 변화는 없었다. 차후 다양한 염색 처리방법 연구와 신뢰성과 객관적 결과를 위한 측정 연구가 필요하다.