• 한국강구조학회 논문집
• /
• 제23권1호
• /
• pp.61-72
• /
• 2011

본 연구에서는 일체식교대 강교량 거더-교대 연결부의 강체거동 및 균열저항성능의 향상을 위한 구조상세를 제시하고 그에 따른 연결부의 거동을 실험적으로 평가하였다. 거더-교대 연결부의 강체거동 및 균열저항성능을 향상시키기 위하여 전단연결재 및 tie bar를 적용한 연결부를 제시하였으며, 제시된 연결부 실험체와 기존 시공경험에 의해 설계된 연결부 실험체의 하중재하실험을 통하여 연결부의 성능 및 거동 특성을 검토하였다. 하중재하실험 결과, 모든 강 거더-교대 연결부 실험체들은 목표 설계하중 및 항복하중 이하에서 충분한 강성 및 균열저항 성능을 보여 강 거더-교대 연결부로 적용 가능하다. 하지만 실험체의 초기 강성, 균열의 진전형상 측면, 하중-변형률 측면에서 전단연결재와 tie bar가 적용된 강 거더-교대 연결부가 기존에 적용되어 왔던 강 거더-교대 연결부에 비하여 구조적으로 우수한 것으로 판단된다.

• Steel and Composite Structures
• /
• 제38권3호
• /
• pp.319-336
• /
• 2021

To achieve a rational detail of the girder-abutment joints in composite integral bridges, and validate the performance of the joints with perfobond connectors, this paper proposes two innovative types of I-shaped steel girder-concrete abutment joints with perfobond connectors intended for the most of bearing capacity and the convenience of concrete pouring. The major difference between the two joints is the presence of the top flange inside the abutments. Two scaled models were investigated with tests and finite element method, and the damage mechanism was revealed. Results show that the joints meet design requirements no matter the top flange exists or not. Compared to the joint without top flange, the initial stiffness of the one with top flange is higher by 7%, and the strength is higher by 50%. The moment decreases linearly in both types of the joints. At design loads, perfobond connectors take about 70% and 50% of the external moment with and without top flange respectively, while at ultimate loads, perfobond connectors take 53% and 26% of the external moment respectively. The ultimate strengths of the reduced sections are suggested to be taken as the bending strengths of the joints.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.389-396
• /
• 1998

One solution to prevent deterioration due to expansion joint and to extend lifetime of short span bridges, is jointless integral abutment bridge. To understand behavior of pile foundation of skewed plate girder bridge with integral abutment, finite element analysis was performed for the model of different skew angle from 90。 to 50。. Comparison of stresses at pile and abutment was made for each case. It is found that effect of temperature change is major factor to influence the behavior of skewed integral abutment bridge.

• Steel and Composite Structures
• /
• 제26권2호
• /
• pp.227-239
• /
• 2018

Integral abutment bridges (IABs) have no joint across the length of bridge and are therefore also known as jointless bridges. IABs have many advantages, such as structural integrity, efficiency, and stability. More importantly, IABs have proven to be have both low maintenance and construction costs. However, due to the restraints at both ends of the girder due to the absence of a gap (joint), special design considerations are required. For example, while replacing the deck slabs to extend the service life of the IAB, the buckling strength of the steel girder without a deck slab could be much smaller than the case with deck slab in place. With no deck slab, the addition of thermal expansion in the steel girders generates passive earth pressure from the abutment and if the applied axial force is greater than the buckling strength of the steel girders, buckling failure can occur. In this study, numerical simulations were performed to estimate the buckling strength of typical steel girders in IABs. The effects of girder length, the width of flange and thickness of flange, imperfection due to fabrication and construction errors on the buckling strengths of multiple and single girders in IABs are studied. The effect of girder spacing, span length ratio (for a three span girder) and self-weight effects on the buckling strength are also studied. For estimation of the reaction force of the abutment generated by the passive earth pressure of the soil, BA 42/96 (2003), PennDOT DM4 (2015) and the LTI proposed equations (2009) were used and the results obtained are compared with the buckling strength of the steel girders. Using the selected design equations and the results obtained from the numerical analysis, equations for preventing the buckling failure of steel girders during deck replacement for maintenance are presented.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 가을 학술발표회 논문집
• /
• pp.95-102
• /
• 1997

Jointless bridge is a new construction method applicable to bridge of short length. In the jointless bridge expansion of superstructure due to thermal effect was absorbed in the flexible pile-type abutment in stead of expansion joint in the conventional bridges. By removing expansion joint, it retards deterioration and extends life time of bridge. In this paper, jointless bridge of steel box girder type was studied through finite element analysis. Stress variations of superstructure and pile due to thermal effect was studied for the two span continuous integral bridge of 80m length and the results of analysis was presented.

• 복합신소재구조학회 논문집
• /
• 제5권2호
• /
• pp.21-26
• /
• 2014

This paper introduces general concepts of jointless bridges and field construction case of semi-integral bridge with psc girder integrating end-diaphragm. The expansion joints need to satisfy thermal and safety conditions of bridges. General bridges with joints have some problems, which are frequently replacement cycle time from mechanical damage or unstable movement, maintenance cost and more. To solve these problems, Integral Abutment Bridges(IAB) have been applied overseas in the 1930s. In Korea, first IAB was constructed in the early 2000s and precast IAB systems was invented and applied lately. Kyungshin overpass bridge in Incheon is the Semi-IAB constructed, the span length is 2@35=70m and the width is 13.9m. The original plan was to use general joint bridge but design field changed with expectations for advanced economic estimation and maintenance. This changed method of B.I.B bridge construction provided not only workability, construction cost but also safety improvement at the same time.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권1호
• /
• pp.123-128
• /
• 2018

기존 거더 형식의 교량이나 슬래브 교량에서는 신축이음장치, 받침, 역T형 교대 및 별도의 접속슬래브 구조를 이루는 시스템으로 이루어져 있다. 이러한 시스템은 신축이음부의 빈번한 파손으로 인한 비용증가, 모멘트 재분배가 낮은 구조로 인한 내구성 감소 등의 문제가 있다. 상기의 문제를 개선하기 위해 일체식 및 반일체식 복합 교량을 제안하고 구조해석을 통해 안전성을 검토하였다. 검토결과 단면강성은 작지만 접속슬래브와 본체 구조가 연속 강결된 다연속 프레임 구조계 형성과 상부구조의 경간과 단면강성의 균형으로 인하여 모멘트재분배와 힘전달이 확실하게 이루어져 기존교량에 비해 구조안전성 높은 구조임을 확인하였다.