• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.708-712
• /
• 2008

Piles and pile foundations have been in common use since very early times. Usually function of piles is to carry load to a depth at which adequate support is available. Another important use of piles is to furnish lateral support and nowadays it is getting highlighted due to the wind load, lateral action of earthquake, and so on. After Broms (1964), many researchers have been suggested methods for estimating lateral capacity of pile. But each method assumes different earth pressure distribution and lateral earth pressure coefficient and it gives confusion to pile designers. Lateral earth pressure, essential in lateral capacity estimation, influenced by pile's behavior under lateral load. Prasad and Chari (1999) assumed the rotation point of pile and suggested an equation of ultimate lateral load capacity. In this study, we investigate the depth of rotation point in both homogeneous soil and multi layered soil, and compare to the estimation value by previous research. To model the pile set up in the sand, we use the chamber and small scale steel pile, and rain drop method. Test results show the rotation point is formed where the Prasad and Chari's estimation value, and they also show multi layered condition affects to location of rotation point to be scattered.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1638-1646
• /
• 2008

This paper presents a series of numerical simulations on the thermal performance and sectional efficiency of a closed-loop vertical ground heat exchanger (U-loop) equipped in a geothermal heat pump system (GHP). A 2-D finite element analysis, ANSYS, was employed to evaluate the temperature distribution on the borehole cross section involving HDPE pipe/grout/soil formation to compare the sectional efficiency between the conventional U-loop and a new latticed HDPE pipe system which is equipped with a thermally insulating latice in order to reduce thermal interference between the inflow and outflow pipes. In addition, a 3-D finite volume analysis (Fluent) was used to simulate the operating process of the closed-loop vertical ground heat exchanger by considering the effect of grout's thermal properties, rate of circulation pump, distance between the inflow and outflow pipes, and the effectiveness of the latticed HDPE pipe system. It was observed that the thermal interference between the two strands of U-loop is of importance in determining the efficiency of the ground heat exchanger, and thus it is highly recommendable to modify the cross section configuration of the conventional U-loop system by including a thermally insulating latice between the two strands.

• 한국터널지하공간학회 논문집
• /
• 제4권1호
• /
• pp.79-90
• /
• 2002

현재 복개 터널 라이닝의 설계는 설계상의 간편성으로 인해 복개 터널의 라이닝에 대한 구조해석적 기법인 Rigid Frame Analysis가 널리 사용되고 있으나, 이는 되메움 지반과 터널 라이닝 사이의 상호작용(Interaction) 메카니즘을 적절히 반영하지 못하게 될 뿐만 아니라, 굴착 사면의 경사, 굴착폭 및 지표면의 경사 등에 의한 영향을 고려하지 못하는 문제점이 있다. 따라서 본 연구에서는 복개 터널구조물의 합리적이고 경제적인 설계를 위한 기본연구로써, 좁은 되메움 공간에서의 토압경감과 콘크리트 라이닝과 성토체의 상호작용을 고려하기 위하여 지반공학적 모델링 기법을 이용한 수치해석을 실시하였다. 또한 복개 터널구조물의 역학적 거동 영향인자로써 굴착사면의 경사 및 콘크리트 라이닝과 굴착사면의 이격거리 등을 고려하였으며, 각 영향인자가 복개 터널구조물의 역학적 거동에 영향을 미치는 정도를 분석하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회 3차
• /
• pp.3-10
• /
• 2010

Case study was carried out on the interpretation of the mechanical behavior of a severely damaged reinforced earth wall comprising geotextile with the concrete panel facing. In this part I, the outline of the damaged reinforced earth wall is in detail described. The background and cause of the damage are discussed based on the results of site investigation. The engineering properties of the fill were examined by performing various in-situ and laboratory tests, including the surface wave survey (SWS), PS-logging, RI-logging, soaking test, the direct shear box (DSB) test, bender element (BE) test, etc. The background as well as the cause for the damage of the wall may be described such that i) a considerable amount of settlement took place over a 3m thick weak soil layer in the lower part of the reinforced earth due to seepage of rainfall water, ii) the weight of the upper fill was partially supported by the geo-textile hooked on the concrete panels (n.b., named conveniently "hammock state" in this paper), and iii) the concrete panels to form the hammock were severely damaged by the unexpectedly large downwards compression force triggered by the tension force of the geotextile. The numerical simulation for the hammock state of the wall, together with counter-measures to re- stabilize the wall is subsequently described in Part II.

• 한국산학기술학회논문지
• /
• 제17권1호
• /
• pp.79-87
• /
• 2016

본 논문에서는 하이브리드 해상풍력발전 지지구조물의 콘크리트베이스와 파일기초를 연결하는 베이스-슬리브 연결부를 제시하고 이를 실험적으로 검증하였다. 베이스-슬리브 연결부의 펀칭 전단 강도와 구조거동을 분석을 위하여, 철근비와 하중조건을 변수로 하는 3개의 연결부 실험체에 대하여 펀칭전단실험이 실시하였다. 실험 결과, 베이스-슬리브 연결부의 펀칭전단강도와 강성은 베이스의 철근비에 주로 영향을 받는 것으로 나타났다. 축력과 모멘트가 동시에 작용되는 하중 조건은 연결부의 강성에는 영향을 미치지 않으나 축력-모멘트 상호작용에 의하여 강도에 영향을 미치는 것으로 나타났다. 또한, 각 실험체의 파괴거동과 펀칭전단의 위험단면에 대해 검토되었다.

• 한국농공학회지
• /
• 제35권2호
• /
• pp.43-56
• /
• 1993

The laboratory tests are performed on how the liquefaction potential of the sea dike structures on the saturated sand or silty sand seabed could be affected due to earthquake before and after construction results are given as follows ; 1. Earthquake damages to sea dike structures consist of lateral deformation, settlement, minor abnormality of the structures and differential settlement of embankments, etc. It is known that severe disasters due to this type of damages are not much documented. Because of its high relative cost of the preventive measures against this type of damages, the designing engineer has much freedom for the play of judgement and ingenuity in the selection of the construction methods, that is, by comparing the cost of the preventive design cost at a design stage to reconstruction cost after minor failure. 2. The factors controlling the liquefaction potential of the hydraulic fill structure are magnitude of earthquake(max. surface velocity), N-value(relative density), gradation, consistency(plastic limit), classification of soil(G & vs), ground water level, compaction method, volumetric shear stress and strain, effective confining stress, and primary consolidation. 3. The probability of liquefaction can be evaluated by the simple method based on SPT and CPT test results or the precise method based on laboratory test results. For sandy or silty sand seabed of the concerned area of this study, it is said that evaluation of liquefaction potential can be done by the one-dimensional analysis using some geotechnical parameters of soil such as Ip, Υt' gradation, N-value, OCR and classification of soils. 4. Based on above mentioned analysis, safety factor of liquefaction potential on the sea bed at the given site is Fs =0.84 when M = 5.23 or amax= 0.12g. With sea dike structures H = 42.5m and 35.5m on the same site Fs= 3.M~2.08 and Fs = 1.74~1.31 are obtained, respectively. local liquefaction can be expected at the toe of the sea dike constructed with hydraulic fill because of lack of constrained effective stress of the area.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.141-149
• /
• 2018

In this paper, the creep behavior of bolted rock was analyzed by using the unconfined creep tests and the numerical results. Based on the test results, the Bolted Burgers creep model (B-B model) was proposed to clarify the creep mechanism of rock mass due to rock bolts. As to the simulation of the creep behaviour of bolted rock, a new user-defined incremental iterative format of the B-B model was established and the open-source $FLAC^{3D}$ code was written by using the object-oriented language (C++). To check the reliability of the present B-B creep constitutive model program, a numerical model of a tunnel with buried depth of 1000 m was established to analyze the creep response of the tunnel with the B-B model support, the non-support and the bolt element support. The simulation results show that the present B-B model is consistent with the calculated results of the inherent bolt element in $FLAC^{3D}$, and the convergence deformation can be more effectively controlled when the proposed B-B model is used in the $FLAC^{3D}$ software. The big advantage of the present B-B creep model secondarily developed in the $FLAC^{3D}$ software is the high computational efficiency.

• 지질학회지
• /
• 제54권6호
• /
• pp.605-614
• /
• 2018

지질학적 현상을 연구하는 물리적 실험의 경우, 반복성 있는 현상 재현이 가능할 때 실험의 신뢰성을 증대시킬 수 있다. 본 연구에서는 인장력에 의해 발생한 정단층 구조를 대상으로 모형 토조를 이용한 벤치마크 실험을 수행하였다. 이를 위해 모형 실험의 상사성을 검토하고, 벤치마크 실험에서와 같은 방법으로 실험 재료와 인장조건, 그리고 경계조건을 설정하여 실험을 수행하였다. 또한 대형 원심모형실험시설을 이용하여 동일한 크기의 모형에서 원심중력가속도와 인장 속도를 변화시켜 인장 거동 시의 물리량에 대한 상사비를 고려하였다. 1 g 상태에서의 벤치마크 실험과 10 g 상태에서의 원심중력장에서 일정한 속도의 인장 응력을 구현하고, 지표면의 형상을 신뢰성 있게 계측하였다. 이를 통해 지각의 변형 실험 연구를 수행 시, 대형 원심모형실험의 신뢰성과 적용성을 평가하였다.

• 한국터널지하공간학회 논문집
• /
• 제23권6호
• /
• pp.485-502
• /
• 2021

터널 굴착으로 인해 필연적으로 발생되는 지반침하 및 상부 구조물 영향 평가를 수행하기 위해 지표침하와 구조물 건전도 저감의 총 7개의 주요 영향 인자들을 설정하고 수치해석을 이용한 Parameter Study를 수행하였다. 그 결과를 통해 Boscardin and Cording 구조물 손상도표를 이용한 안정성 분석, 최대침하량과 각변위를 이용한 안정성 분석을 수행하고 각각의 주요 영향 인자들에 대한 상관성 분석을 실시하였다. 또한, 매개변수 해석을 통한 지반 및 구조물 상호거동 양상을 이용하여 경기도 화성시에 위치한 𐩒𐩒𐩒터널 현장에 적용하고 현장 적용성을 분석하였다. 그 결과 오차가 약 1.0%로 나타나 설계단계에서의 터널 굴착에 따른 구조물 안정성 평가 시 다양한 조건에서 적합한 노선 결정을 위한 기초 자료로 활용될 수 있도록 하였다.

• Geomechanics and Engineering
• /
• 제25권3호
• /
• pp.195-205
• /
• 2021

Time effect on the deformation and strength characteristics of geogrid reinforced sand retaining wall has become an important issue in geotechnical and transportation engineering. Three physical model tests on geogrid reinforced sand retaining walls performed under various loading conditions were simulated to study their rate-dependent behaviors, using the presented nonlinear finite element method (FEM) analysis procedure. This FEM was based on the dynamic relaxation method and return mapping scheme, in which the combined effects of the rate-dependent behaviors of both the backfill soil and the geosynthetic reinforcement have been included. The rate-dependent behaviors of sands and geogrids should be attributed to the viscous property of materials, which can be described by the unified three-component elasto-viscoplastic constitutive model. By comparing the FEM simulations and the test results, it can be found that the present FEM was able to be successfully extended to the boundary value problems of geosynthetic reinforced soil retaining walls. The deformation and strength characteristics of the geogrid reinforced sand retaining walls can be well reproduced. Loading rate effect, the trends of jump in footing pressure upon the step-changes in the loading rate, occurred not only on sands and geogrids but also on geogrid reinforced sands retaining walls. The lateral earth pressure distributions against the back of retaining wall, the local tensile force in the geogrid arranged in the retaining wall and the local stresses beneath the footing under various loading conditions can also be predicted well in the FEM simulations.