• Journal of Conservation Science
• /
• v.7 no.1
• /
• pp.9-18
• /
• 1998

There are about 1470 stone-cultural properties in Korea which have been registered and protected by the government. Representative of them are pagoda, stupa, stone-buddha, stele support of banner pole and stone-lanterns. Most of them have been exposed to and weathered by natural environments. Stone-cultural properties are destroyed and/or destructed mostly by weathering and its related features of rocks. Therefore, it is necessary to conduct geological studies on the weathering phenomena and related features as well as characteristics of the rock itself must be done for the conservation. Thus geological investigation should include detail measurements, rock varieties and phases, structural lineaments of the rock, cause and degree of weathering, degree and patterns of crack development structural stability, identification of reusable parts for restoration, geomorphological characteristics of the site, and etc. The interaction among these factors must be investigated and analyzed, which must be used as basic data to establish the guideline of conservation and to plan for repair and/or restoration. The conservation plan should involve parts to be repaired, method of repair, type of cementing material, the characteristics of rock phases to be supplemented, method for maintaining structural stability, and method to delay or to prevent the rock weathering.

• Journal of Korean Society of Forest Science
• /
• v.108 no.2
• /
• pp.216-223
• /
• 2019

This study was conducted to measure the changes in the geological and soil properties following slow-moving landslide events in Yangbuk-myun and Gyungju-si, Gyeongsangbuk-do, South Korea. The geological characteristics of the study site comprised black shale in the Gyeongsang nodal group formed in the Cretaceous period and quartz feldspar carcinoma in the east side with conglomerate in the Yeonil group formed in the Quaternary period. The study site exhibited the geologic characteristics of a slow-moving landslide with severely weathered rocks. The maximum collapsing depth of the slow-moving landslide was 12.0 m with colluvial deposits. The strike and joint aspects in the slope areas of the slow-moving landslides were $N46^{\circ}E$ in lower slope and $N62^{\circ}E$ in upper slope, respectively. Soil hardness of ${\leq}20cm$ deep was not measured because of the completely disturbed soil resulting from soil creeping. Soil from 25 to 90 cm deep was 1.4-4.7 times softer in the slow-moving landslide areas than in the undisturbed or natural forests. Soil bulk density was $1.24-1.29g/cm^3$ in land creep areas. Soil bulk in both areas was 1.6 times denser than that in the natural forest. The soil pore space was 51.5-53.3% in the land creep areas. The values are 1.3-1.4 times lower than those within the natural forest. Black shale areas showed the lowest coefficient of permeability (8.75 E-06 cm/s) and mesopore ratio (pF 2.7: 9.8%) compared with those resulting from other study areas.

• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.445-471
• /
• 2023

Long-term safety over millennia is the top priority consideration in the construction of disposal sites. However, ensuring the mechanical stability of deep geological repositories for spent fuel, a.k.a. radwaste, disposal during construction and operation is also crucial for safe operation of the repository. Imposing restrictions or limitations on tunnel support and lining materials such as shotcrete, concrete, grouting, which might compromise the sealing performance of backfill and buffer materials which are essential elements for the long-term safety of disposal sites, presents a highly challenging task for rock engineers and tunnelling experts. In this study, as part of an extensive exploration to aid in the proper selection of disposal sites, the anticipation of constructing a deep geological repository at a depth of 500 meters in an unknown state has been carried out. Through a review of 2D and 3D numerical analyses, the study aimed to explore the range of properties that ensure stability. Preliminary findings identified the potential range of rock properties that secure the stability of central and disposal tunnels, while the stability of the vertical tunnel network was confirmed through 3D analysis, outlining fundamental rock conditions necessary for the construction of disposal sites.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.83-92
• /
• 2005

Fluid conductivity logging has been applied in the boreholes to identify the permeable fi:actures and estimate the origin of saline groundwater in coast area. Fluid replacement technique measures the fluid electrical conductivity with depth at different times in a well after the borehole is first washed out with different water by passing a tube to the borehole bottom. Then formation water flows into the borehole through aquifer such as permeable fractures or porous formation during ambient or pumping condition. Measured conductivity profiles with times therefore indicate the locations of permeable zone or fractures within the open hole or the fully slotted casing hole. As a result of fluid conductivity logging for three boreholes in the study area, it is interpreted that saline groundwater is caused by seawater intrusion through fractured rock, although the effect by land reclamation partially remains. We are planning the quantitative analysis to estimate the hydraulic characteristics using fluid replacement technique, and this approach might be usefully utilized for assessing the characteristics of seawater intrusion, the design of optimal pumping, and estimating the hydraulic properties in coastal aquifer.

• Tunnel and Underground Space
• /
• v.22 no.6
• /
• pp.412-428
• /
• 2012

To achieve mine development, a large amount of data concerned with the geological structure and the ore body had to be investigated and collected through geological survey, drilling and geophysical explorations. In most previous cases, however, the data were usually analyzed two dimensionally and those results showed some limits because of their 2D presentation. Those 2D maps such as geological plane sections or longitudinal sections cause lots of difficulties in understanding the complex geological structure or the feature of ore body in a spatial way. In this study, research area was set on the abandoned Yangyang iron mine in Korea and the Sugaeng ore body within the mine was selected as the research target to design a mine haulage system for reopening. A 3D mine model of this area was tried to be constructed using a 3D modelling software, GEMS. An accurate 3D model including the ore body, the geological structure, the old underground mine drifts and the new mine drifts was constructed under the purpose of reopening of the abandoned iron mine. Especially, mine design for trackless haulage system was conducted. New inclines and drifts were planned and modelled 3 dimensionally considering the utilization of old drifts and shaft. In addition to the 3D modelling, geostatistical technique was adopted to generate a spatial distribution of the ore grade and the rock physical properties. 3D model would be able to contribute in solving problems such as evaluating ore reserves, planning the mine development and additional explorations and changing the development plans, etc.

• The Journal of Engineering Geology
• /
• v.20 no.1
• /
• pp.35-45
• /
• 2010

The soil tests have been performed on the specimens obtained from about 1,150 sites including landslides and non-landslides areas in natural terrains for last 10 years. Based on the results of those tests, the average soil properties are estimated and the simple equations for estimating permeability are proposed according to geologic conditions. The average permeability in Granite and Mudstone sites is higher than other sites and the content of silt and clay in Mudstone and Gneiss sites is higher than other sites. The correlation analysis and the regression analysis were performed to estimate the coefficient of permeability according to geological conditions. As the result of the correlation analysis, the coefficient of permeability is selected as a dependent variable, and the silt and clay contents, the water contents and the dry unit weights are selected as independent variables. As the result of the regression analysis, the silt and clay contents and the void ratio were involved commonly in the linear regression equations according to geological conditions. To verify the proposed the linear regression equations, the measured result of the coefficient of permeability at other sites was compared with the result predicted with the proposed equations. As the result of comparison, there were a little bit different between them for some data. However the difference was relatively small. Therefore, the linear regression equations for estimating the coefficient of permeability according to geological conditions may be applied to Korean soils. However, these equations should be verified and corrected continuously to improve the accuracy.

• The Journal of the Petrological Society of Korea
• /
• v.18 no.3
• /
• pp.211-221
• /
• 2009

This study illustrates the relationship between the petrographic characteristics of micrographic granite and the topographic features around Ijin-ri. Light-brown to light- gray granite is composed of intergrown fine-grained quartz + orthoclase, displaying micrographic textures. Miarolitic cavities are abundant. Many micro-landforms including tor, tafoni, and gnamma occurred in the micrographic granite of the study area. Tafoni is dominant in the north and gnamma is dominant in south. From our study of the occurrence and textural properties, two alteration zones were clearly identified; one is an external zone (A) characterized by abundant of small sized miarolitic cavities and the other is an internal zone (B) having them less than zone A. The former is dominant in north, and the latter is dominant in south. Particular geomorphologic features such as fluting cores and raised rims are present in the Ijin-ri area. This suggests that development of miarolitic cavities played an important role in the formation of the various geomorphologic features. Consequently, the petrogenesis of the micrographic granite is related to geomorphologic features in the external zone typified by abundant tafoni such as the tiger rock, and the formation of a platform as micro-landforms is influenced by thetextural differences of host rock in the internal zone.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.1
• /
• pp.73-84
• /
• 2010

We studied the geological occurrence, associated minerals, mineralogical properties and formation process of tremolites from two abandoned asbestos mines, Jungang (Sinsuk) and Daebosuksan, located in Boryoung area, Chungnam. Morphologically different tremolites such as long fibrous, needle-like, bladed and prismatic forms coexisted. Fibrous tremolite, known for its high toxieity to human health, was systematically analyzed by polarized light microscopy and scanning electron microscopy. The average length of tremolite fibers was 31.2 ${\mu}m$ although the maximum length of some asbestos was 210.0 ${\mu}m$. The average width and aspect ratio were 1.6 ${\mu}m$ and 19.9, respectively. Tremolite showed inclined extinction in the range of 6.1~20.2$^{\cric}$. X-ray diffraction patterns were slightly different between fibrous (asbestiform) and prismatic (non-asbestiform) tremolites. EPMA analysis of tremolites in the study area indicated extremely high Mg content with very low Fe content, close to the composition of tremolite in end-member in the tremolite-actinolite solid solution series. The formational conditions of asbestiform and non-asbestiform tremolite appear to be different. Asbestiform tremolite was estimated to have been formed in later stage.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.281-281
• /
• 2006

In this study, the polyurethane which has versatile applications has been reinforced with the natural clay, hectorite. The hectorite has better properties than montmorillonite. There are studies on polyurethane and montmorillonite but polyurethane and hectorite composite is published first time. Polyurethane is industrial polyurethane which makes the study to be applicable to the industry. Exfoliated structure has been obtained without using organic modifiers due to the hydrophilic nature of the polymer matrix and the mineral clay. Mechanical properties have been improved as well.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.594-596
• /
• 2007

Using an oedometer cell instrumented to measure the evolution of electromagnetic properties, small strain stiffness, and temperature, we conducted consolidation tests on four types of sediments. The tested specimens include sediments with different gas hydrate saturation at four stages of loading. The test results show that the electromagnetic and mechanical properties of hydrate-bearing marine sediments are governed by the vertical effective stress, stress history, porosity, hydrate saturation, fabric, ionic concentration of the pore fluid, and temperature. The results also show that permittivity and electrical conductivity data can be combined to estimate hydrate volume fraction in laboratory sediments, methodology that might eventually be extended for estimation of hydrate concentrations in field settings.