• Journal of Soil and Groundwater Environment
• /
• v.21 no.3
• /
• pp.64-81
• /
• 2016

To analyze the influence of various groundwater flow rates (specific discharge) on BHE system with balanced and unbalanced energy loads under assuming same initial temperature (15℃) of ground and groundwater, numerical modeling using FEFLOW was used for this study. When groundwater flow is increased from 1 × 10⁻⁷ to 4 × 10⁻⁷m/s under balanced energy load, the performance of BHE system is improved about 26.7% in summer and 22.7% at winter time in a single BHE case as well as about 12.0~18.6% in summer and 7.6~8.7% in winter time depending on the number of boreholes in the grid, their array type, and bore hole separation in multiple BHE system case. In other words, the performance of BHE system is improved due to lower avT in summer and higher avT in winter time when groundwater flow becomes larger. On the contrary it is decreased owing to higher avT in summer and lower avT in winter time when the numbers of BHEs in an array are increased, Geothermal plume created at down-gradient area by groundwater flow is relatively small in balanced load condition while quite large in unbalanced load condition. Groundwater flow enhances in general the thermal efficiency by transferring heat away from the BHEs. Therefore it is highly required to obtain and to use adequate informations on hydrogeologic characterristics (K, S, hydraulic gradient, seasonal variation of groundwater temperature and water level) along with integrating groundwater flow and also hydrogeothermal properties (thermal conductivity, seasonal variation of ground temperatures etc.) of the relevant area for achieving the optimal design of BHE system.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.119-126
• /
• 2004

A small-scale reinforced earth wall was constructed in a laboratory to investigate the effect of wall rigidity and of construction sequence on the wall. A full continuous wall facing and a discrete wall facing were designed and constructed for tests. These two different facing systems should adapt different construction procedures due to their different facing shapes. The model wall was built with geo-grid reinforcement, sand, and facings on rigid surface. The model wall was instrumented with earth pressure gages, LVDTs, and strain gages. The experimental results have shown differences in wall behavior related to construction sequence and types of wall facing. It is found in this study that the reinforced earth wall built with full continuous facing is safer than the reinforced earth wall built with the discrete wall facing.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.18 no.3
• /
• pp.233-240
• /
• 2000

A small rivers take advantage of not only a site of superb scenic beauty, a play space, a rest place but also a momentous waters reservoir, a drainage on territory residents. Likewise, part of the most massed a life space to a region dwellers shall be extremely in harmony with coexistence space in that every kind plant, animal over again a human being and so on. For improvement planning of small river, various way and model are presented. But, it's want of ability for small rivers of a adaption many-side and throwing in a lot of financial resources. Because the improvement planning of small river was designed all small river in a county, the priority must be preprocessed. Now, the counties prioritized for improvement planning of small river are a few, and acquisition and manipulation of the data are time-consuming. Geo-Spatial Information System (GSIS) is specifically designed to manage and analyze spatial data. It will be to offer the benefit to the determination of the improvement priority in a small river. The purpose of this study is to offer priority for improvement planning of small river using GSIS. For this purpose, it was developed using Arc/Info software and AML was used as a developing tool.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.372-372
• /
• 2022

스마트시티 하천관리를 위해 선행된 연구에서는 도시하천관련 데이터를 수집-정제-제공하는 도시하천 통합데이터 플랫폼을 개발하였다. 이에 하천 분석을 위한 유역 유출, 하천 흐름 그리고 도시유출 등의 모듈과 하천 환경, 친수, 종합 평가 모델을 연계하여 도시하천관리 연계플랫폼으로 연구개발을 진행하였다. 본 연구에서는 스마트시티 하천관리를 위한 시나리오 기반 제방 파제 시뮬레이션 분석 결과 가시화 모듈에 관한 연구를 진행한다. 부산 EDC 지역을 대상으로 DEM, 항공영상, 위성영상, 하천 지리 정보, 하천 단면도 등의 데이터를 결합하여 하천 및 유역 전산 3D 형상 모델링을 진행한다. 또한 하천 내부 유량 및 파제 제체 모델링, 유동장 격자 모델링을 통해 제방 붕괴 범람 시뮬레이션 대상 지역을 구현한다. 해당 EDC 지역 구현 모델에 연속방정식, 운동량방정식, 수송방정식 등 지배방정식과 삼상 유동 기법 등 수치 해석 기법을 활용하여 제방 파제 시뮬레이션을 수행한다. 시뮬레이션의 침수범위 및 침수심 분포 결과는 위경도를 포함한 ASCII Grid로 반환되며 GeoServer를 통한 좌표계 설정 및 도시하천 연계플랫폼에서 가시화하는 연구를 진행하였다. 제방 파제 시나리오는 제방 높이 2m, 제방 폭 7.5m, 파제 길이 20m로 설정하여 4개의 붕괴 위치를 지정하였고, 지정된 위치에 대한 제방 파제 3D 시뮬레이션을 통해 도출된 Case 별 2D/3D 영상과 침수심 공간 분포에 대한 Raster Graphics를 전처리하여 시나리오별 침수범위-침수심을 도시하천 연계플랫폼 상에서 가시화하는 연구를 진행하였다. 도시하천 연계플랫폼의 시나리오 기반 제방 파제 시뮬레이션 모듈을 통하여 스마트시티의 제방 파제 피해 양상 및 대책 마련 의사결정 보조로 활용할 수 있을 것으로 기대된다.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.1
• /
• pp.21-35
• /
• 2016

It is a current trend that the concrete track is applied for high speed railway. In the case of the railway embankment constructed on soft ground, the damage to concrete track which is sensitive to settlement such as distortion and deflection could be caused by very small amount of long term settlement. Pile Supported Embankment method can be considered as the effective method to control the residual settlement of the railway embankment on soft ground. The Geosynthetics is used inside of the embankment to maximize the arching effect transmitting the load of the embankment to the top of the piles. But, PHC piles that are generally used for bridge structures are also applied as the pile supporting the load of embankment concentrated by the effect of the Geosynthetics. That is very low efficiency in respect of pile material. So, in this study, the cast in place concrete pile was selected as the most suitable pile type for supporting the embankment by a case study and the optimum mixing condition of concrete using a by-product of industry was induced by performing the mixing designs and the compressive strength designs. And it is shown that the cast in place pile with the optimum mixing condition using the by-product of industry is 2.8 times more efficient than the PHC pile for the purpose of Pile Supported Embankment by the finite element analysis method.

• Geophysics and Geophysical Exploration
• /
• v.9 no.3
• /
• pp.241-249
• /
• 2006

Due to the long tectonic history and the very complex geologic formations in Korea, the anisotropic characteristics of subsurface material may often change very greatly and locally. The algorithms commonly used, however, may not give sufficiently precise computational results of traveltime data particularly for the complex and strong anisotropic model, since they are based on the two-dimensional (2D) earth and/or weak anisotropy assumptions. This study is intended to develope a three-dimensional (3D) modeling algorithm to precisely calculate the first arrival time in the complex anisotropic media. Considering the complex geology of Korea, we assume 3D TTI (tilted transversely isotropy) medium having the arbitrary symmetry axis. The algorithm includes the 2D non-linear interpolation scheme to calculate the traveltimes inside the grid and the 3D traveltime mapping to fill the 3D model with first arrival times. The weak anisotropy assumption, moreover, can be overcome through devising a numerical approach of the steepest descent method in the calculation of minimum traveltime, instead of using approximate solution. The performance of the algorithm developed in this study is demonstrated by the comparison of the analytic and numerical solutions for the homogeneous anisotropic earth as well as through the numerical experiment for the two layer model whose anisotropic properties are greatly different each other. We expect that the developed modeling algorithm can be used in the development of processing and inversion schemes of seismic data acquired in strongly anisotropic environment, such as migration, velocity analysis, cross-well tomography and so on.

• Korean Journal of Remote Sensing
• /
• v.38 no.5_3
• /
• pp.953-966
• /
• 2022

Since aerosols adversely affect human health, such as deteriorating air quality, quantitative observation of the distribution and characteristics of aerosols is essential. Recently, satellite-based Aerosol Optical Depth (AOD) data is used in various studies as periodic and quantitative information acquisition means on the global scale, but optical sensor-based satellite AOD images are missing in some areas with cloud conditions. In this study, we produced gap-free GeoKompsat 2A (GK-2A) Advanced Meteorological Imager (AMI) AOD hourly images after generating a Random Forest based gap-filling model using grid meteorological and geographic elements as input variables. The accuracy of the model is Mean Bias Error (MBE) of -0.002 and Root Mean Square Error (RMSE) of 0.145, which is higher than the target accuracy of the original data and considering that the target object is an atmospheric variable with Correlation Coefficient (CC) of 0.714, it is a model with sufficient explanatory power. The high temporal resolution of geostationary satellites is suitable for diurnal variation observation and is an important model for other research such as input for atmospheric correction, estimation of ground PM, analysis of small fires or pollutants.

• Journal of Navigation and Port Research
• /
• v.26 no.3
• /
• pp.323-328
• /
• 2002

Soil-steel structures have been used for the underpass, or drainage systems in the road embankment. This type of structures sustain external load using the correlations with the steel wall and engineered backfill materials. Buried flexible conduits made of corrugated steel plates for the coastal road was tested under vehicle loading to investigate the effects of live load. Testing conduits was a circular structure with a diameter of 6.25m. Live-load tests were conducted on two sections, one of which an attempt was made to reinforce the soil cover with the two layers of geo-gird. Hoop fiber strains of corrugated plate, normal earth pressures exerted outside the structure, and deformations of structure were instrumented during the tests. This paper describes the measured static and dynamic load responses of structure. Wall thrust by vehicle loads increased mainly at the crown and shoulder part of the conduit. However additional bending moment by vehicle loads was neglectable. The effectiveness of geogrid-reinforced soil cover on reducing hoop thrust is also discussed based on the measurements in two sections of the structure. The maximum thrusts at the section with geogrid-reinforced soil cover was 85-92% of those with un-reinforced soil cover in the static load tests of the circular structure; this confirms the beneficial effect of soil cover reinforcement on reducing the hoop thrust. However, it was revealed that the two layers of geogrid had no effect on reducing the overburden pressure at the crown level of structure. The obtained values of DLA decrease approximately in proportion to the increase in soil cover from 0.9m to 1.5m. These values are about 1.2-1.4 times higher than those specified in CHBDC.

• Journal of the Korean Geographical Society
• /
• v.41 no.1 s.112
• /
• pp.106-120
• /
• 2006

Natural or man-made disaster has been expected to be one of the potential themes that can integrate human geography and physical geography. Typhoons like Rusa and Maemi caused great loss to insurance companies as well as public sectors. We have implemented a natural disaster management system for a private insurance company to produce better estimation of hazards from high wind as well as calculate vulnerability of damage. Climatic gauge sites and addresses of contract's objects were geo-coded and the pressure values along all the typhoon tracks were vectorized into line objects. National GIS topog raphic maps with scale of 1: 5,000 were updated into base maps and digital elevation model with 30 meter space and land cover maps were used for reflecting roughness of land to wind velocity. All the data are converted to grid coverage with $1km{\times}1km$. Vulnerability curve of Munich Re was ad opted, and preprocessor and postprocessor of wind velocity model was implemented. Overlapping the location of contracts on the grid value coverage can show the relative risk, with given scenario. The wind velocities calculated by the model were compared with observed value (average $R^2=0.68$). The calibration of wind speed models was done by dropping two climatic gauge data, which enhanced $R^2$ values. The comparison of calculated loss with actual historical loss of the insurance company showed both underestimation and overestimation. This system enables the company to have quantitative data for optimizing the re-insurance ratio, to have a plan to allocate enterprise resources and to upgrade the international creditability of the company. A flood model, storm surge model and flash flood model are being added, at last, combined disaster vulnerability will be calculated for a total disaster management system.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.1
• /
• pp.109-119
• /
• 2016

The height datum of Korea is currently separated into land and sea, which makes it difficult to acquire homogeneous and accurate height information throughout the whole nation. In this study, we therefore tried to suggest the more effective way to transform the height information were constructed separately according to each height datum on land and sea to those on the unique height datum using precise geoid models and tidal observations in Korea. For this, Anmyeon island was selected as a study area to develop the precise geoid models based on the height datums land (IMSL) and sea (LMSL), respectively. In order to develop two hybrid geoid models based on each height datum of land an sea, we firstly develop a precise gravimetric geoid model using the remove and restore (R-R) technique with all available gravity observations. The gravimetric geoid model were then fitted to the geometric geoidal heights, each of which is represented as height datum of land or sea respectively, obtained from GPS/Leveling results on 15 TBMs in the study area. Finally, we determined the differences between the two hybrid geoid models to apply the height transformation between IMSL and LMSL. The co-tidal chart model of TideBed system developed by Korea Hydrographic and Oceanographic Agency (KHOA) which was re-gridded to have the same grid size and coverage as the geoid model, in order that this can be used for the height datum transformation from LMSL to local AHHW and/or from LMSL to local DL. The accuracy of height datum transformation based on the strategy suggested in this study was approximately ${\pm}3cm$. It is expected that the results of this study can help minimize not only the confusions on the use of geo-spatial information due to the disagreement caused by different height datum, land and sea, in Korea, but also the economic and time losses in the execution of coastal development and disaster prevention projects in the future.