• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2583-2588
• /
• 2013

A new type of solid and gel-state ionics based on siloxane pyridinium iodides was synthesized and used as electrolytes in dye-sensitized solar cells. The resulting electrolytes were characterized by $^1H$ NMR spectroscopy, TGA and diffusion coefficient. The synthesized siloxane pyridinium iodide electrolytes have characteristics of different chain length of siloxane moieties. The ion conductivities were given 2.7-3.2 S/cm. Among the three SiDPIs based electrolytes, DSSC employing the SiDPI2 gives an open circuit voltage of 0.704 V, a short-circuit current of 15.85 $mA/cm^2$ and conversion efficiency of 6.8% under light intensity of 100 $mW/cm^2$. In addition, the performance of the DSSCs showed relatively reasonable compared with the propylpyridinium iodide (PPI) electrolyte.

• Journal of Powder Materials
• /
• v.29 no.6
• /
• pp.485-491
• /
• 2022

Lithium lanthanum titanium oxide (LLTO) is a promising ceramic electrolyte because of its high ionic conductivity at room temperature, low electrical conductivity, and outstanding physical properties. Several routes for the synthesis of bulk LLTO are known, in particular, solid-state synthesis and sol-gel method. However, the extremely low ionic conductivity of LLTO at grain boundaries is one of the major problems for practical applications. To diminish the grain boundary effect, the structure of LLTO is tuned to nanoscale morphology with structures of different dimensionalities (0D spheres, and 1D tubes and wires); this strategy has great potential to enhance the ion conduction by intensifying Li diffusion and minimizing the grain boundary resistance. Therefore, in this work, 0D spherical LLTO is synthesized using ultrasonic spray pyrolysis (USP). The USP method primarily yields spherical particles from the droplets generated by ultrasonic waves passed through several heating zones. LLTO is synthesized using USP, and the effects of each precursor and their mechanisms as well as synthesis parameters are analyzed and discussed to optimize the synthesis. The phase structure of the obtained materials is analyzed using X-ray diffraction, and their morphology and particle size are analyzed using field-emission scanning electron microscopy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.761-765
• /
• 2007

NASICON sensors compare properties with manufacture method in order to improve $CO_2$ sensitivity and stability the sensing behaviors. Oxidation mixing method and Sol-gel method were compare analyze to characteristic in which each other sintered to $900^{\circ}C\;to\;1100^{\circ}C$ and NASICON $CO_2$ gas sensors were fabricate. Oxidation mixing method showed better sensing properties at sintered $1100^{\circ}C$ result to NASICON electrolyte analyze with manufacture methods.

• Journal of the Korean Ceramic Society
• /
• v.45 no.11
• /
• pp.662-666
• /
• 2008

Electrochemical properties of carbon cryogel electrode for the application of composite electrode materials mixed with metal oxide in supercapacitor have been studied. Carbon cryogels were synthesized by sol-gel polycondensation of resorcinol with form aldehyde, followed by a freeze drying, and then pyrolysis in an inert atmosphere. Physical properties of carbon cryogel were characterized by BET, X-ray diffraction (XRD) and scanning electron microscopy (SEM). It is found that carbon cryogel is amorphous material. The electrochemical properties of carbon cryogel were measured by cyclic voltammetry as a function of concentration of liquid electrolyte, galvanostatic charge-discharge with different scan rates and electrochemical impedance measurements. The result of cyclic voltammetry indicated that the specific capacitance value of a carbon cryogel electrode was approximately 150.2 F/g (at 5 mV/s in 6M KOH electrolyte).

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.610-618
• /
• 1998

Alumina were added to ceria based ceramic powders upto 9.7 vol% and composite powders were sprayed by plasma spraying process in order to improve the mechanical properties such as hardness fracture tough-ness and thermal shock resistance. The ceria based coating sprayed without alumina has the typical colum-nar and lamellar structure. Alumina addition has lowered the amount of columnar and lamellar sturcture Added alumina was segreagated in the grain boundary and grain of ceria based crystal accompanied with pore. The maximum value of density and the minimum value of porosity were observed at the sprayed coating with 4.8 vol% alumina. The hardness fracture toughness and thermal shock resistance were increased with alumina addition. The improvement of mechanical properties of plasma sparyed ceria based coatings result-ed from the disapperance of the columnar and lamellar sturcture by addition of alumina.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1130-1132
• /
• 2009

We propose a novel way for enhancement of efficiency on a quasi solid-state dye-sensitized solar cell (DSSC). It contained gel type electrolyte mixing the liquid crystal (LC) of specific concentration and applied voltage for alignment of the LC. Aligned LC is supported charge transfer inside electrolyte and efficiency is increased in DSSC. We made a quasi solid-state DSSC which applied DC voltage or not and have measured the power conversion efficiency (PCE) and the fill factor. From measurement, we obtain high performances in case of cell applied voltage compare to reference cell.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.120-124
• /
• 2008

Carbon-coated $LiFePO_4$ and $LiMn_{0.4}Fe_{0.6}PO_4$ cathode materials for lithium batteries were synthesized by a sol-gel method. X-ray diffraction and scanning electron microscopy data showed that the cathode materials are pure crystalline and are surrounded by porous carbon. The initial discharge capacities of $LiFePO_4$ and $LiMn_{0.4}Fe_{0.6}PO_4$ with the liquid electrolyte of 1M $LiPF_6$ in EC/DMC are 132 mAh/g and 145 mAh/g, respectively, at current density of 0.1 C-rate. $LiFePO_4$ and $LiMn_{0.4}Fe_{0.6}PO_4$ with an electrospun polymer-based electrolyte exhibit initial discharge capacities of 114 and 130 mAh/g at 0.1 C-rate at room temperature, respectively.

• Membrane Journal
• /
• v.20 no.3
• /
• pp.259-266
• /
• 2010

Porous poly(propylene) supported gel polymer electrolytes (GPE) were synthesized by thermal polymerization of DEGDMA [Di(ethylene glycol) dimethacrylate] in electrolyte solutions (1 M solution of $LiPF_6$ in EC/DEC 1 : 1 mixture) at $70^{\circ}C$. AC impedance spectroscopy and cyclic voltammetry were used to evaluate its ionic conductivity and electrochemical stability window of the GPE membranes. Lithium ion battery (LIB) cells were also fabricated with $LiNi_{0.8}Co_{0.2}O_2$/graphite and GPE membranes via thermal polymerization process. Through the thermal polymerization, self sustaining GPE membranes with sufficient ionic conductivities (over $10^{-3}\;S/cm$) and electrochemical stabilities. The LIB cell with 5% monomer showed the best rate-capability and cycleability.

• Korean Journal of Materials Research
• /
• v.34 no.4
• /
• pp.185-193
• /
• 2024

In this study, NASICON-type Li_1+XGa_XTi_2-X(PO₄)₃ (x = 0.1, 0.3 and 0.4) solid-state electrolytes for all-solid-state batteries were synthesized through the sol-gel method. In addition, the influence on the ion conductivity of solid-state electrolytes when partially substituted for Ti⁴⁺ (0.61Å) site to Ga³⁺ (0.62Å) of trivalent cations was investigated. The obtained precursor was heat treated at 450 ℃, and a single crystalline phase of Li_1+XGa_XTi_2-X(PO₄)₃ systems was obtained at a calcination temperature above 650 ℃. Additionally, the calcinated powders were pelletized and sintered at temperatures from 800 ℃ to 1,000 ℃ at 100 ℃ intervals. The synthesized powder and sintered bodies of Li_1+XGa_XTi_2-X(PO₄)₃ were characterized using TG-DTA, XRD, XPS and FE-SEM. The ionic conduction properties as solid-state electrolytes were investigated by AC impedance. As a result, Li_1+XGa_XTi_2-X(PO₄)₃ was successfully produced in all cases. However, a GaPO₄ impurity was formed due to the high sintering temperatures and high Ga content. The crystallinity of Li_1+XGa_XTi_2-X(PO₄)₃ increased with the sintering temperature as evidenced by FE-SEM observations, which demonstrated that the edges of the larger cube-shaped grains become sharper with increases in the sintering temperature. In samples with high sintering temperatures at 1,000 ℃ and high Ga content above 0.3, coarsening of grains occurred. This resulted in the formation of many grain boundaries, leading to low sinterability. These two factors, the impurity and grain boundary, have an enormous impact on the properties of Li_1+XGa_XTi_2-X(PO₄)₃. The Li_1.3Ga_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 ℃ was denser than those sintered at other conditions, showing the highest total ion conductivity of 7.66 × 10^-5 S/cm at room temperature. The total activation energy of Li-ion transport for the Li_1.3Ga_0.3Ti_1.7(PO₄)₃ solid-state electrolyte was estimated to be as low as 0.36 eV. Although the Li_1+XGa_XTi_2-X(PO₄)₃ sintered at 1,000 ℃ had a relatively high apparent density, it had less total ionic conductivity due to an increase in the grain-boundary resistance with coarse grains.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.141-144
• /
• 2003

Proton conducting polymeric gels as the electrolytes of electrochemical capacitors have been prepared by two different methods: 1) swelling a polymethacrylate-based polymer matrix in aqueous solutions of inorganic and organic acids, and 2) polymerizing complexes of anhydrous acids and prepolymers with organic plasticizer. The FT-IR spectra strongly suggest that the carbonyl groups in the polymer matrix interact with protons from the doped acids. High ionic (proton) conductivity in the range of $6\times10^{-4}-4\times10^{-2}\;S\;cm^{-1}$ was obtained at room temperature for the aqueous gels. The non-aqueous polymer complexes showed rather low ionic conductivity, but it was about $10^{-3}\;S\;cm^{-1}\;at\;70^{\circ}C$ for the $H_3PO_4$ doped polymer electrolyte. The mechanisms of ion (proton) conduction in the polymeric systems are discussed.