• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.139-142
• /
• 2009

As important mechanical elements, gears have been used widely in power transferring systems such as automobile transmission and there have been several researches trying to make gear parts with cold or warm forging in order to reduce cost and time required to gear manufacturing process. Although forging processes of spur and bevel gears have been developed as practical level owing to active previous researches in Korea, the manufacturing of helical gear has been still depended on traditional gear cutting processes such as hobbing, deburring and shaving. In order to manufacture helical gears with cold forging process, a research project supported by government has been conducted by Daegu university, KIMS and TAK and this paper deals with effects of back pressure forming technique to cold forging of helical gear as a fundamental research.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.389-390
• /
• 2006

Selective surface densification is a tool for improving the mechanical properties of PM steels, such that the requirements for highly loaded gears can be matched. This paper describes the manufacturing and the properties of a helical P/M gear. The gear performance was evaluated on a 3-shaft back to back test rig, on a load bearing test rig and on a sound test bench. The results of these tests are presented and compared to data obtained from solid steel gear with identical geometry and surface quality. This comparison indicates that P/M gears have a load bearing capacity and noise level which are both well comparable to solid steel gears.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.9
• /
• pp.77-83
• /
• 1996

This paper describes forging of trochoidal gears, which are being widely used in timing belt pulley, pump pulley etc., as a series of development of the simulator for non-axisymmetric elements. Kinematically admissible velocity fields for forging of trochoidal gear were proposed and the loads were calculated by numerical method. When the simulation was carried out, half pith of gear was divided into 6 deformation regions which have different velicity fields by assumptions and boundary conditions. The neutral surface was introduced into forging of trochoidal gears with flat punch and, for each step, it is assumed as a circle with its radius r$_{n}$. The experimental set-up was installed in 200 ton hydraulic press for forging. The billets, of A1 2218 aluminum alloy, were slightly phosphate-coated. It was shown that thd theoretical solutions, as upper bound, are useful to predict the forging load for forging of trochoidal gears, because thdt give estimates that are substantially higher than experimental loads.s.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.17-17
• /
• 2017

In electric agricultural machine the gearhead is needed to convert the high speed low torque rotation motion generated by DC motor to lower speed high torque motion used by the vehicle. The gearhead consist of several spur gears works as reduction gears. Spur gear have straight tooth and are parallel to the axis of the wheel. Spur gears are the most easily visualized gears that transmit motion between two parallel shafts and easy to produce. The modeling and simulation of spur gears in DC motor gearhead is important to predict the actual motion behavior. A pair of spur gear tooth in action is generally subjected to two types of cyclic stress: contact stress and bending stress including bending fatigue. The stress may not attain their maximum values at the same point of contact fatigue. These types of failure can be minimized by analysis of the problem during the design stage and creating proper tooth surface profile with proper manufacturing methods. To improve its life expectation in this study modal and stress analysis of gearhead is simulated using ansys work bench software based on finite element method (FEM). The modal analysis was done to understand gearhead deformation behaviour when vibration occurs. FEM static stress analysis is also simulated on gearhead to simulate the gear teeth bending stress and contact stress behavior. This methodology serves as an approach for gearhead design evaluation, and the study of gear stress behavior in DC motor gearhead which is needed in the small workshop scale industries.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.3
• /
• pp.184-193
• /
• 2008

For environment-friendly fishery, the lead sinkers of octopus drift line were developed with the environmentfriendly sinker, and their characteristics and performance were investigated. To make the environmentfriendly sinker, the hydrate ceramic material was developed, and to increase the weight and strength, the iron power was added to it. The fishing hook was machine-made, and standardized, by using 60cm iron wire. For the manufacture of the sinker, the first, the mold was made, and then, hydrate ceramic material and water were quantitatively mixed. The mixture was poured into the mold prepared with a fishing hook already inserted, and had hardened for several hour, before it was taken out of the mold as a complete sinker. The sinkers were made in the 8 types ranging in weight from 150 to 500g, and their specific gravities were diverse from 2.871 to 6.637, which was 0.19 to 0.44 times lower than that of lead. The movement of the environment-friendly sinker by flume tank was possible in the weaker current speed than the similar lead sinker. In the coastal fishing grounds of Gangwon province, the comparison of catching efficiency was made between the improved fishing gears composed of the environment-friendly sinkers and artificial baits, and the current used fishing gears of lead sinkers and pig-fat baits. The result showed the tendency in which the improved fishing gears caught the bigger octopuses than the current used fishing gears. In the quantity and number of the fish catch per unit fishing gear, the improved fishing gear showed a little more catch than the current used fishing gear, regardless of the fishing area. However, the number of the improved fishing gears lost during fishing operation was similar to that of the current used fishing gears.

• Journal of Computational Design and Engineering
• /
• v.1 no.1
• /
• pp.27-36
• /
• 2014

Similar to the essential components of many mechanical systems, the geometrical properties of the teeth of spiral bevel gears greatly influence the kinematic and dynamic behaviors of mechanical systems. Logarithmic spiral bevel gears show a unique advantage in transmission due to their constant spiral angle property. However, a mathematical model suitable for accurate digital modeling, differential geometrical characteristics, and related contact analysis methods for tooth surfaces have not been deeply investigated, since such gears are not convenient in traditional cutting manufacturing in the gear industry. Accurate mathematical modeling of the tooth surface geometry for logarithmic spiral bevel gears is developed in this study, based on the basic gearing kinematics and spherical involute geometry along with the tangent planes geometry; actually, the tooth surface is a parametric surface defined on a parallelogrammic domain. Equivalence proof of the tooth surface geometry is then given in order to greatly simplify the mathematical model. As major factors affecting the lubrication, surface fatigue, contact stress, wear, and manufacturability of gear teeth, the differential geometrical characteristics of the tooth surface are summarized using classical fundamental forms. By using the geometrical properties mentioned, manufacturability (and its limitation in logarithmic spiral bevel gears) is analyzed using precision forging and multiaxis freeform milling, rather than classical cradle-type machine tool based milling or hobbing. Geometry and manufacturability analysis results show that logarithmic spiral gears have many application advantages, but many urgent issues such as contact tooth analysis for precision plastic forming and multiaxis freeform milling also need to be solved in a further study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.9
• /
• pp.1027-1032
• /
• 2012

Two types of very small multiplying gears and arrays have been developed for new dental hand-pieces, and the increased speed ratios, modules, number of teeth, gear diameters, and gear types were calculated based on the dynamics of the machinery. The contacting and bending strengths were evaluated for gear teeth with two design concepts using AGMA equations and finite element analyses, and the contacting stresses on teeth with and without DLC (diamond-like-carbon) coating layers were calculated. Fatigue and tension tests were performed to obtain an S-N curve, the Young's modulus, and the strength of the gear material, and these were utilized in the analyses. Slightly larger stresses were found for 2-axis-type gears than for other types of gears, and the S-N curves showed that a gear lifetime of 109 cycles was satisfied. The contacting stresses in gears coated with DLC were reduced by 30%. A new prototype model of a hand-piece with small gears was successfully fabricated and tested.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.632-637
• /
• 1993

Rating systems of bevel gears(straight, spiral, and zerol bevel gears) which are commonly used as power transmission devices for non-parallel axes are developed on the personal computer, which analyze and/or evaluate the gear design and the service performance at the point of view of strength and durability. The typical considerations of the ratings are the bending strength the surface durability, and the scoring resistance. The ratings are carried out using the reliable standards of AGMA & Gleason Works. Therefore, the system is built so that the variables or factors considered differently in those standards and the strength, durability, and scoring partially in Gleason are appraised separatedly by each method, and a series of the estimation processes is integrated into the system so as to compare each result. The developed rating system can be used in the initial stage of gear design process, and also a better design can be performed by the evaluation of the initial design at the view point of gear strength and durability. Additionally, it is useful for the trouble-shooting of bevel gear systems and to the purpose of introducing the methods for maintaining design strength in service with appraising the gear strength after design or with appraising the influencing factors, as a whole. Therefore, this rating systems can help the aim of design automation of bevel gears.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.168-173
• /
• 1999

It is investigated that internal defect of planetary gear which consists of two gears with different number of teeth on both side. The internal defect, central burst, begin to form at the place of adiabatic shear band which usually has maximum ductile fracture value during the forming operation, forward and backward extrusion. It makes the plastic forming of planetary gear difficult. The prediction of defect to minimize the cost to produce the planetary gear. The finite element simulation code DEFORM is applied to analyze the defects. In the analysis, the toothed gears are assumed as axisymmetric cylinders whose diameters are equal to those of pitch circles of the each gears. Experiments were carried out with the SCM415 alloy steel as billet material and AIDA 630-ton knuckle-joint press. The calculated results and experimental inspections are compared to design a die and blank without defects and the results are useful to predict the internal defect.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.13-18
• /
• 2011

This study deals with the effect of the honing in SCM420H planetary gears. The hardness, tooth profile, lead and roughness of the gear surface can be improved by honing. Therein, the honing techniques are welcomed especially as one of the physical surface improvement methods. As a result, gear honing reduces vibration and noise, and will increase the life of gear. And gear honing also changes the surface of gear tooth in a short time and price, so it is a very important method in manufacturing industry. But nowadays, it is hard to find the detail information of gear honing. The test gear is a planetary gear which is used in the automotive industry. It is manufactured by the hobbing, shaving, carburizing and honing. This study investigates the effect of honing in surface shape of SCM420H planetary gears, including fatigue strength test and characteristics of honing of SCM420H planetary gears.