• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.360-364
• /
• 1994

This paper is concerned with extracting the diagnostic signature for motor-operated valves (MOV's) noninvasively. A torque estimator is developed and tested to obtain electical torque of the induction motors which are attached to the MOV's. Inverse filter is used to recover the gear meshing forces from the measured actuator housing vibration, which contain the gear rotation information. Frequency demodulation techniques are performed and an adaptive linear bandpass filter is implemented to improve signal-to-noise ratio. Finally, stand-alone valve experiments are carried out to validate the signature extraction scheme.

• International Journal of Automotive Technology
• /
• v.7 no.3
• /
• pp.315-320
• /
• 2006

We have developed an active front steering system(AFS) with a planetary gear train, which can vary the steering gear ratio according to the vehicle speed and improve vehicle stability by superimposing steering angle. We conducted vehicle tests showing that co-operated control of AFS with ESP can improve vehicle stability by direct control of tire slip angle and that steering reaction torque during AFS intervention can be compensated by torque compensation using electric power steering.

• Tribology and Lubricants
• /
• v.4 no.2
• /
• pp.60-67
• /
• 1988

Conventional theory of gear mechanism can't be applied to analyze the harmonic drive due to specific movement of the teeth. This paper deals with an analysis of kinematics and geometry of the tooth engagement of a harmonic drive comprising circular spline, flexspline and wave generator. A theoretical new tooth profile of the flexspline in meshing internal rigid gear with involute profile is obtained. Characteristics of harmonic drive reducer are shown according to parameters such as deviation coefficient, deviation distance, addendum modification coefficient. As an example, the design of harmonic drive with 1:80 reduction ratio is presented.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.4
• /
• pp.276-286
• /
• 2009

The main purpose of this research is to analyze economic feasibility of biodegradable sonw crab gill net model project. The results of benefit/cost analysis show that use of the biodegradable gear is economically feasible. Assuming that the rate of gill net lost is 5 percent, net present value was estimated 311,898,282-590,533,375won, benefit-cost ratio 1.816-1.923 and internal rate of return 7.96-10.59%. The development and diffusion of biodegradable fishing gear appear to make a significant contribution to fisheries resource conservation and marine ecosystem protection. In addition, biodegradable gear production firms may have a good opportunity of exporting it to other coastal states, depending on the progress of WTO subsidy negotiation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.4
• /
• pp.59-65
• /
• 2010

This paper presents the study on the contact stress analysis of a pair of mating spur gears during rotation. Contact stress analysis is performed between two spur gear teeth at different contact positions during rotation. An example is presented to investigate the variation of contact stress on a pair of mating gears with contact positions. The variation of contact stress during rotation is compared with the contact stress at lowest point of single tooth contact(LPSTC) and AGMA Equation for contact stress. The results show that contact stress varies along the contact position and gets maximum values in the beginning and end of the contact. In this study, the gear design considering the contact stress on a pair of mating gears is more severe than that of AGMA standard.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1495-1505
• /
• 2002

As combining the functions of a 2K-H B type differential gear unit and a V-belt type continuously variable unit(CVU), 16 different mechanisms are presented. Some useful theoretical formula related to speed ratio, power flow and efficiency are derived and analyzed. Continuously variable transmission(CVT) mechanisms are proposed, which can of ffr a backward mode, a geared neutral, an underdrive mode and an overdrive mode. They are not required of a starting device as a torque converter. CVT mechanisms developed here present two distinct operating modes which are a power circulation mode and a power split mode. The transition of two modes takes place at the particular CVU speed ratio. For these CVT mechanisms, performance analysis related to speed ratio, power ratio and theoretical efficiency are executed.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.799-806
• /
• 2007

One method for improving the torque capacity of the CVT is to use a split-powered CVT(SPCVT) to reduce the power transmitted into a continuously variable unit(CVU). A variable bridge SPCVT with two planetary gear units(PGUs), which are composed of a sun gear, a ring gear, and carrier and planetary gears, can minimize the power to the CVU. However, a SPCVT with a conventional CVT should possess a dual mode, which would allow the conventional CVT to be used at high speeds and an additional gear train to be used at low speeds. The inner-spherical CVU(ISCVU) with an inner and outer spherical contact mechanism developed in this study can cover the range from low to high speeds. The rated power and the overall speed ratios were 100 kW and $0.09{\sim}0.36$, respectively. Power efficiency was numerically calculated to be over 90% over the speed ratio range of $0.1{\sim}0.29$. The maximum shear stress at the two contact areas of the rotor pairs, the minimum life and the overall size were estimated to be 700 MPa, 276 kh and $350{\times}350{\times}400mm^3$, respectively. This study shows that an ISCVU and a variable bridge type PGU can realize the SPCVT with a single mode for a vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.218-226
• /
• 2002

This study was carried out to develop continuously variable-speed transmission(CVT) fur an agricultural tractor. The full-toroidal variator mechanism with flour discs and six rollers was utilized as a device fur changing speed ratio continuously. In system layout design, the sizes of the roller cylinders and the end-load cylinder, which were critical factors for controlling the variator, were designed. The planetary gear unit and six pairs of the gear assemblies were designed to establish the maximum speed of the vehicle at 30 ㎞/hr. In addition, the hydraulic clutch, the silent chain, the hydraulic manifold and the electronic controller were designed. Based on the design, a prototype CVT was developed and tested. Test results show that the CVT developed in this study could successfully provide variable speed of the tractor.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.1
• /
• pp.5-14
• /
• 2005

Continuously variable transmission (CVT) mechanisms combine the functions of a K-H-V type differential gear unit and a V-belt type continuously variable unit (CVU). For the 24 different mechanisms, 12 of them are power circulation modes while the other 12 are power split modes. Some useful theoretical formulas related to speed ratio, power flow and efficiency were derived and analyzed. These mechanisms have many advantages: they decrease CVT size and weight, increase overall efficiency, extend speed ratio range, and generate geared neutral. Compound CVTs were developed by combining the power circulation mode and power split mode, which can offer backward motion, geared neutral, underdrive and overdrive.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.4
• /
• pp.96-103
• /
• 2005

We designed the compound CVT(Continuously Variable Transmissions) by combining power circulation mode and power split mode, which have been proposed for connecting 2K-H I differential gear to the V- belt type CVU(Continuously Variable Unit), as an input coupled type. With the designed compound CVT, we carried out theoretical analysis and performance experiments for efficiency, speed ratio, power flow, and power transmission ratio. We proved that the compound CVT had a better performance than either of the power circulation mode or power split mode.