• 터널과지하공간
• /
• 제7권2호
• /
• pp.100-107
• /
• 1997

In case of a fire outbreak in a uni-directional road tunnel, the flow of traffic immediately behind the fire disaster will be stalled all the way back to the entrance of the tunnel. Furthermore, when the vehicle passengers try to flee away from the fire toward the entrance of the tunnel, the extremely hot fume that propagates in the same direction will be fatal to the multitudes evacuating, but may also cause damage to the ventilation equipments and the vehicles, compounding the evacuation process. This paper will present the 3-dimensional modelling analysis of the preventive measures of such a fume propagation in the same direction as the evacuating passengers. For the analysis, the fire hazard was assumed to be a perfect combustion of methane gas injected through the 1 m X 2 m nozzle in the middle of the tunnel, and the product of $CO_2$ as the indicator of the fume propagation. From the research results, when the fire hazard occurred in middle of the 400 m road tunnel, the air density decreased around the fire point, and the maximum temperatures were 996 K and 499 K at 210 m and 350 m locations, respectively, 60 seconds after fire disaster occurred, when the fumes were driven out only towards the exit-direction of the tunnel. By tracing the increase of $CO_2$ level over 1% mole fraction, the minimum longitudinal ventilation velocity was found to be 2.40 m/sec. Furthermore, through Analysis of the temperature distribution graphs, and observation of the cross-sectional distribution of $CO_2$ over 1% mole fraction, it was found that the fume did not mix with the air, but rather moved far in a laminar flow towards exit of the tunnel.

• 한국결정성장학회지
• /
• 제13권1호
• /
• pp.5-14
• /
• 2003

Principles of a novel pulse growing method are described. The method realized in the crystal growing on a seed from melts under raw melt feeding provided a more reliable control of the crystallization process when producing large alkali halide crystals. The slow natural convection of the melt in the crucible at a constant melt level is intensified by rotating the crucible, while the crystal rotation favors a more symmetrical distribution of thermal stresses over the crystal cross-section. Optimum rotation parameters for the crucible and crystal have been determined. The spatial position oi the solid/liquid phase interface relatively to the melt surface, heaters and the crucible elements are considered. Basing on that consideration, a novel criterion is stated, that is, the immersion extent of the crystallization front (CF) convex toward the melt. When the crystal grows at a <> CF immersion, the raised CF may tear off from the melt partially or completely due to its weight. This results in avoid formation in the crystal. Experimental data on the radial crystal growth speed are discussed. This speed defines the formation of a gas phase layer at the crystal surface. The layer thickness il a function of time a temperature at specific values of pressure in the furnace and the free melt surface dimensions in the gap between the crystal and crucible wall. Analytical expressions have been derived for the impurity component mass transfer at the steady-state growth stage describing two independent processes, the impurity mass transfer along the <> path and its transit along the <> one. The heater (and thus the melt) temperature variation is inherent in any control system. It has been shown that when random temperature changes occur causing its lowering at a rate exceeding $0.5^{\circ}C/min$, a kind of the CF decoration by foreign impurities or by gas bubbles takes place. Short-term temperature changes at one heater or both result in local (i.e., at the front) redistribution of the preset axial growth speed.

• Korean Chemical Engineering Research
• /
• 제47권3호
• /
• pp.362-367
• /
• 2009

최근 직접 액체 연료전지의 연료로써의 개미산은 메탄올의 대안으로 부상하고 있다. 본 논문에서는 직접 개미산 연료전지(DFAFCs, Direct Formic Acid Fuel Cells)의 운전 조건을 변화시켜 성능을 측정 및 분석하였다. 예를 들면, 양이온 교환 막의 두께, 개미산 수용액의 농도, 기체 확산층과 상용 촉매 등을 비교 및 분석하였다. 양이온 교환 막의 두께는 크로스오버(cross-over)와 연관되어 성능에 영향을 크게 주었다. 성능 최적화를 위해 개미산의 농도를 변화시켰다. 또한 개미산 산화에 가장 활성이 높은 상용촉매를 찾기 위해 실험했다. 나피온($Nafion^{(R)}$)-115, Pt-Ru black 상용촉매로 막-전극 접합체를 구성하여 6 M 개미산 수용액으로 운전하였을 때 최적의 성능을 보였다. 직접 메탄올 연료전지(DMFCs, Direct Methanol Fuel Cells)와 비교하여 우수한 성능을 보였다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제23권2호
• /
• pp.197-204
• /
• 2010

Two studies were conducted to determine the effects of replacing 30% (% in diet DM) of lucerne (Medicago sativa L.) hay with citrus pulp in Merino ewe diets: i) an in vitro study which measured ruminal fermentation; and ii) an in vivo study in which twelve Merino ewes pre- and post-lambing were fed experimental diets in a cross-over design over 120 days to evaluate effects on ewe performance (i.e. DM intake, average daily gain (ADG) and wool growth). In both the in vitro and in vivo studies, the control treatment consisted of lucerne (91.3% in diet DM), lupins (8.3% in diet DM) and phosphate (0.42% in diet DM), while the citrus pulp treatment consisted of lucerne (57.7% in diet DM), lupins (9.5% in diet DM), phosphate (0.48% in diet DM) and fresh citrus pulp (32.3% in diet DM). Data were analysed using the mixed model procedure of SAS. In the in vitro study, gas production, total volatile fatty acid (VFA) yield, proportion of propionic acid to total VFA and in vitro dry matter digestibility (IVDMD) were higher (p<0.02) in the citrus pulp treatment compared to the control treatment. In contrast, in vitro ammonia production, pH and the acetate to propionate ratio were lower (p<0.03) for the citrus pulp treatment compared to the control treatment. In the in vivo study, DM intake of ewes fed the citrus pulp diet was lower than their control ewe counterparts throughout both the pre- and post-lambing periods (928.9 vs. 1,115.0 g/d pre-; 1,285.0 vs. 1,620.3 g/d post-lambing, p<0.01), however ADG was similar (p = 0.12). Wool growth parameters and lamb performance did not differ (p>0.32) between treatments. In summary, the in vitro study demonstrated that the replacement of 30% of a lucerne diet with fresh citrus pulp improved total VFA yield, increased total gas production and improved IVDMD, while decreasing the production of ammonia, acetic acid and rumen pH. In addition, the in vivo study demonstrated that the replacement of 30% of a lucerne diet with fresh citrus pulp pre- and post-lambing decreased intake but did not affect ewe performance in terms of ADG and wool growth. These findings, of course, would be of significant interest to sheep producers endeavouring to control cost of feed ingredients whilst maintaining productivity.

• 한국재료학회지
• /
• 제19권2호
• /
• pp.90-94
• /
• 2009

The development of low-k materials is essential for modern semiconductor processes to reduce the cross-talk, signal delay and capacitance between multiple layers. The effect of the $CH_4$ concentration on the formation of SiOC(-H) films and their dielectric characteristics were investigated. SiOC(-H) thin films were deposited on Si(100)/$SiO_2$/Ti/Pt substrates by plasma-enhanced chemical vapor deposition (PECVD) with $SiH_4$, $CO_2$ and $CH_4$ gas mixtures. After the deposition, the SiOC(-H) thin films were annealed in an Ar atmosphere using rapid thermal annealing (RTA) for 30min. The electrical properties of the SiOC(-H) films were then measured using an impedance analyzer. The dielectric constant decreased as the $CH_4$ concentration of low-k SiOC(-H) thin film increased. The decrease in the dielectric constant was explained in terms of the decrease of the ionic polarization due to the increase of the relative carbon content. The spectrum via Fourier transform infrared (FT-IR) spectroscopy showed a variety of bonding configurations, including Si-O-Si, H-Si-O, Si-$(CH_3)_2$, Si-$CH_3$ and $CH_x$ in the absorbance mode over the range from 650 to $4000\;cm^{-1}$. The results showed that dielectric properties with different $CH_4$ concentrations are closely related to the (Si-$CH_3$)/[(Si-$CH_3$)+(Si-O)] ratio.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.96-101
• /
• 2007

[ $YBa_2Cu_3O_{7-{\delta}}$ ] films have been prepared on $LaAlO_3$ (100) single-crystal substrates by a metalorganic deposition using dichloroacetate precursors (DCA-MOD). Calcination conditions were varied in order to optimize the microstructure and the superconducting properties of YBCO film. Coated films were calcined at various temperatures ranging from $400{\sim}700^{\circ}C$ in flowing humid oxygen atmosphere. Ramping rate to calcination tempertures was $2.22^{\circ}C/min$. Conversion heat treatment was performed at $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. Observations of surface and cross sectional SEM microstructure showed that the particle size in the calcined film increased in the range of 100-200 nm with heating rate and the calcination temperature. SEM EDS analysis showed that 13 a/o of chlorine was contained in the calcined film. It was also observed that the porosity increased with the heating rate and temperature. Porous microstructure was developed when YBCO films were prepared using porous calcined film. Dense microstructure and high $J_c$ over $1\;MA/cm^2$ was obtained when calcination was carried out at the temperature of $500^{\circ}C$ with a heating rate of $2.22^{\circ}C/min$.

• 한국강구조학회 논문집
• /
• 제13권5호
• /
• pp.577-586
• /
• 2001

이 연구에서는 다 셀계수변수와 다 제약조건으로 구성된 단면 및 시스템 형상을 동시에 고려하는 입체 트러스의 이산화 최적설계 문제를 유전자 알고리즘을 이용하여 체계화하였다. 또한 유전자 알고리즘의 적용방법을 초기화절차 진화적 절차 그리고 유전적 절차로 구성하였다. 초기화 절차에서는 한 세대의 개체 수만큼 염색체를 생성하고 진화적 절차는 구조해석의 결과를 분석하여 적합도를 계산하였다. 그리고 유전적 절차는 복제와 교배 및 돌연변이를 통하여 다음 세대의 유전자를 생성하게 된다. 이렇게 진화적 절차와 유전적 절차를 반복 수행하여 최적 해를 탐색한다. 이 연구에서는 설계자가 궁극적 목표로 하는 구조물의 구조 해석과 단면 및 시스템 형상 최적설계를 동시에 수행할 수 있는 이산화 최적설계 프로그램을 개발하고 설계 예를 들어 비교 고찰하였다.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.69-75
• /
• 2009

The effects of welding speed were investigated on penetration characteristics, defects and mechanical properties including formability test in Nd:YAG laser welded 1000MPa grade DP steels. A shielding gas was not used and bead-on-plate welding was performed with various welding speeds at 3.5kW laser power. Defects of surface and inner beads were not observed in all welding speeds. As the welding speed increased, the weld cross-section varied from the trapezoid having wider bottom bead, through X type, finally to V type in partial penetration range of welding speeds. The characteristic of hardness distribution was also investigated. The center of HAZ had maximum hardness, followed by a slight decrease of hardness as approaching to FZ. Significant softening occurred at the HAZ near BM. Regardless of the welding speed, the weld showed approximately the same hardness distribution. In the perpendicular tensile test with respect to the weld direction, all specimens were fractured at the softening zone. In the parallel tensile test to the weld direction, the first crack occurred at weld center and then propagated into the weld. Good formability over 80% was taken for all welding conditions.

• Animal Bioscience
• /
• 제34권7호
• /
• pp.1146-1156
• /
• 2021

Objective: The aim of the study was to compare the effect of two plant additives, rich in polyphenolic compounds, supplemented to sheep diets on microorganisms and carbohydrate fermentation in rumen. Methods: In the experiment, 6 ewes of the Polish Mountain breed were fitted with ruminal cannulas. Sheep were divided into three feeding groups. The study was performed in a cross-over design of two animals in each group, with three experimental periods (n = 6 per each group). The animals were fed a control diet (CON) or additionally received 3 g of dry and milled lingonberry leaves (VVI) or oak bark (QUE). Additionally, plant material was analyzed for tannins concentration. Results: Regardless of sampling time, QUE diet increased the number of total protozoa, as well as Entodinium spp., Diplodinium spp. and Isotrichidae family, while decreased bacterial mass. In turn, a reduced number of Diplodinium spp. and increased Ophryoscolex spp. population were noted in VVI fed sheep. During whole sampling time (0, 2, 4, and 8 h), the number of protozoa in ruminal fluid of QUE sheep was gradually reduced as opposed to animals receiving CON and VVI diet, where rapid shifts in the protozoa number were observed. Moreover, supplementing sheep with QUE diet increased molar proportions of butyrate and isoacids in ruminal fluid. Unfortunately, none of the tested additives affected gas production. Conclusion: The addition of VVI or QUE in a small dose to sheep diets differently affected rumen microorganisms and fermentation parameters, probably because of various contribution of catechins in tested plant materials. However, it is stated that QUE diet seems to create more favorable conditions for growth and development of ciliates. Nonetheless, the results of the present study showed that VVI and QUE additives could serve as potential natural modulators of microorganism populations and, consequently, carbohydrate digestion in ruminants.

• Korean Chemical Engineering Research
• /
• 제44권6호
• /
• pp.588-596
• /
• 2006

폴리스티렌 막(polystyrene membrane, PS)의 표면을 Ar, $O_2$ 플라즈마로 처리하고, 처리 전후의 변화를 관찰하였고, $CO_2$, $N_2$의 투과도와 $N_2$에 대한 $CO_2$의 선택도는 연속흐름 기체 투과 분석장치(GPA)를 이용하여 측정하였다. Ar플라즈마 처리의 경우 O/C비율이 0에서 0.179로 증가하고, 표면 거칠기가 $15.86{\AA}$에서 $71.64{\AA}$로 증가함으로써 접촉각은 처리전의 $89.16^{\circ}$에서 $18.1^{\circ}$로 감소하였다. 따라서 플라즈마 처리는 막표면을 높은 친수성을 갖도록 만들었다. $CO_2$의 투과도와 선택도에 대한 Ar플라즈마 처리최적조건은 60 W, 2 min, $70^{\circ}C$이며, 투과도와 선택도는 각각 $2.1{\times}10^{-12}[m^3(STP){\cdot}m/m^2{\cdot}sec{\cdot}atm]$와 4.51이었다. $O_2$플라즈마 처리의 경우에, 접촉각은 O/C비율(0.189)과 표면 거칠기($57.10{\AA}$)의 증가에 의해 $13.56^{\circ}$로 감소하였다. 최적의 처리조건은 90 W-2 min-$70^{\circ}C$이며, 값 $7.1{\times}10^{-12}[m^3(STP){\cdot}m/m^2{\cdot}sec{\cdot}atm]$와 값 11.5이었다. 플라즈마 처리 후 막 표면의 변화는 표면에서의 교차결합과 식각효과의 경쟁적인 관계에 의해 결정된다. 결국 플라즈마 처리된 막의 투과도와 선택도가 플라즈마 기체, 처리시간, 출력세기등과 같은 플라즈마 상태를 제어함으로써 향상되었음을 확인할 수 있었다.