• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.177-184
• /
• 2014

PURPOSE. The aim of this study was to measure the changes on the marginal and internal adaptation of zirconia based anterior fixed partial dentures after the porcelain firing process. MATERIALS AND METHODS. A total of 34 anterior fixed partial dentures using LAVA CAD/CAM system (3M ESPE, Germany) were applied. Two silicone replicas were obtained: one is obtained before porcelain firing process (initial) and the other is obtained after porcelain firing process (final), followed by the examination under a binocular stereomicroscope. Kruskal Wallis and Wilcoxon Signed Ranks tests were used for the statistical analysis (P<.05). RESULTS. No statistically significant difference was found between initial and final marginal gap values (P>.05). At the internal gap measurements, final marginal area values ($59.54{\mu}m$) were significantly lower than the initial marginal area values ($68.68{\mu}m$)(P<.05). The highest and the lowest internal gap values were observed at the incisal/occlusal area and at the marginal area, respectively. In addition, lower internal gap values were obtained for canines than for central incisors, lateral incisors and premolars at the incisal area (P<.05). CONCLUSION. The firing cycles did not affect the marginal gap of Lava CAD/CAM system, but it is controversial for the internal gap.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.667-672
• /
• 2009

In case of high-levelled platform in the urban railway system, a certain width of gap is inevitably formed between the train and the platform, and the gap gets wider when it is concerned with curved portion of the tracks at platform. This gap greatly contributes to decrease of passengers' safety while boarding and alighting a train. In particular, it endangers children's safety. Gap filler system is often fitted out to minimize gap and to overcome this safety problem at platform. However, as existing gap fillers are in most case structurally complex and organized to be powered from separate supply unit, there are a range of non-favorable points from the viewpoint of cost, installation and maintenance. In addition, existing gap fillers are due to cause disruptions in operation of train, with failures such as malfunctioning of control system. In this study, the authors will review on the gap filler applicable to the platforms of various height types, which neither requires any modifications of the train nor causes any operational disruptions. The proposed gap filler system here is a by-stage retractile type and based on the idea of interlocking it with train doors open-close mechanism, without any additional power supply unit or control system.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.10a
• /
• pp.539-544
• /
• 1998

Generally, welding gap is a serious factor of a falling-off in weld quality among various kind of weld defect. Welding gap is created between two work piece in GMAW(Gas Metal Arc Welding) of horizontal fillet weld because surface of workpiece is not flat by cutting process. In these days, there were many attempts to detect welding gap. though we prevalently use the vision sensor or arc sensor in welding process, it is difficult to detect welding gap for improvement of welding quality. But we have a trouble to find relationship between welding gap and many welding parameters due to non-linearity of welding process. As mentioned about the various difficult problem, we can detect welding gap precisely using neural networks which are able to model non-linear function. Also, this paper was proposed real-time monitoring of weld bead shape to find effect of welding gap and to estimate weld quality. Monitoring of weld bead shape examined the correlation of welding parameters with bead eometry using learning ability of neural networks. Finally, the developed system, welding gap detecting system and bead shape monitoring system, is expected to the successful capability of automation of welding process by result of simulation.

• International Journal of Contents
• /
• v.13 no.4
• /
• pp.47-62
• /
• 2017

This paper analyzes how much the gap existed between the public group and expert group using future issues and future core technologies that are announced in government institutions based on ontology. We calculated gap with two groups' point of view, one is expert groups' ideas that are based on future hopeful technologies documents, and another is public people ideas that are based on documents of contest that is hosted by 'Ministry of Science, ICT and Future Planning (MSIP)', and 'Institute for Information & communications Technology Promotion (IITP)'. For calculating these, we suggested SDGM model. In the case of ETRI Meta-trend ICT Field, there is a little gap between expert group and public group, and another case that is XT (ETRI determined future technologies excluding ICT field) Field, the gap is increasing annually. Moreover, in the case of all ETRI Meta trend, the gap is bigger than ICT and XT field. We analyzed, also, KEIT's future issues for generalizing this model. The gap existed between two groups. Utilizing SDGM model of this paper, people can interpret easily how much the gap exists between future technologies and issues that are announced in institutions.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1406-1407
• /
• 2007

본 논문에서 제안한 ac-PDP(Plasma display panel) 셀구조는 Long gap의 전극 사이에 보조 전극을 삽입한 구조이다. 일반적으로, long gap 구조를 가진 PDP cell은 높은 방전 개시 전압을 가지므로, Long gap 전극 사이에 보조전극을 삽입하여 방전 개시 전압을 낮춤과 동시에 휘도 상승, 소비 전력의 감소효과로 발광효율의 향상을 가져왔다. 제안한 구조의 구동을 위하여 asymmetric mode와 long gap mode라는 2가지 파형을 가지고 실험하였다. 두 파형은 공통적으로 기존의 ADS(Address and Display period Separated)파형을 Y(Scan), Z(Common), A(Address) 전극에 인가하였으며, 보조적극에는 Z(Common) 전극의 파형을 수정한 형태로 인가하였다. Asymmetric mode는 보조전극에 Z(Common) 전극에 인가되는 파형과 같은 형태의 파형을 인가하여 Long gap의 구조를 가지지만 Short gap에서 방전이 가능하도록 설계하였고, long gap mode는 보조전극에 인가되는 Z(Common) 파형 중 sustain pulse를 초기 3개만을 주어 Short gap에서 방전을 개시함과 동시에 priming 입자를 생성하고, 나머지 sustain 구간에서는 floating시켜 이미 생성된 priming 입자를 long gap에서 구동을 가능하도록 하였다.

• The Journal of Korean Society for Radiation Therapy
• /
• v.22 no.1
• /
• pp.47-51
• /
• 2010

Purpose: In the treatment of high-energy protons Air gap (the distance between the patient and the exit Beam) Lateral Penumbra of the changes to the increase in the radiation fields can form unnecessary and Increase the maximum dose at the site of treatment and reduced the minimum dose homogeneity of dose distributions can decline. Air gap due to this change in dose distribution compared to investigate studied. Materials and Methods: Received proton therapy at our institution Lung, Liver patients were selected and the size of six other Air gap in Field A and Field B 2, 4, 6, 8, 10 cm Proton external beam planning system by setting up a treatment plan established. Air gap according to the Lateral Penumbra area and DVH (Dose Volume Histogram) to compare the maximum dose and minimum dose of PCTV areas were compared. In addition, the dose homogeneity within PCTV Homogeneity index to know the value and compared. Results: Air gap (2, 4, 6, 8, 10 cm) at each change in field size were analyzed according to the Lateral Penumbra region Field A Change in the Air gap 2~10 cm by 1.36~1.75 cm, the average continuously increased about 28.7% and Field B Change in the Air gap 2~10 cm by 1.36~1.75 cm, the average continuously increased about 31.6%. The result of DVH analysis for relative dose of the maximum dose According to Air gap 2~10 cm is the mean average of 110.3% from 108.1% to a sustained increased by approximately 2.03% and The average relative dose of minimum dose is the mean average of 93.9% percent to 90.8 percent from the continuous decrease of about 3.31 percent. The result of Homogeneity index value to the according to Air gap 2~10 cm is the 2-fold increase from 1.09 to 2.6. Conclusion: In proton therapy case, we can see the increasing of lateral penumbra area when airgap getting increase. And increasing of Dmax and decreasing Dmin in the field are making increase homogeneity index, So we can realize there are not so good homogeneity in the PCTV. Therefore we should try to minimize air gap in proton therapy case.

• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.2
• /
• pp.233-238
• /
• 2014

Purpose : The Varian's Eclipse radiation treatment planning system is able to correct radiation treatment thought leaf gap which is limitation MLC movement for collision with both MLC. In this study, I'm try to analyze dosimetric effect about the leaf gap in treatment planning system. And then apply to clinical implement. Materials and Methods : The Elclipse version is 10.0. In general, the leaf gap set to 0.05~0.3 mm and must measurement each leaf gap. The leaf gap measured by each LINACs and photons. We applied to measured each leaf gap in IMRT and VMAT. Changing the leaf gap, we evaluated treatment plans by Dmax, CI, etc. Results : When the same plan was evaluated with changing the leaf gap, an increase of 2-5% over the value Dmax, CI increases mm to 0.0~0.50 mm leaf gap. Volumetric modulated and intensity modulated radiation therapy plans all showed the same trend was not found significant between each radiation treatment planning. Conclusion : Generally, the leaf gap setting has a unique measure of the Multileaf collimator. However, the aging of the Multileaf collimator, calibration, and can be changed, after inspection and repair of the lip gap should eventually because these values affect the treatment plan must be applied to the treatment after confirmation. In some cases, may be to maintain the initial setting value of the lip gap, which is undesirable because it can override the influence on the treatment plan.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.5
• /
• pp.324-333
• /
• 2013

Recently, rudder erosion due to cavitation has been frequently reported on a semi-spade rudder of a high-speed large ship. This problem raises economic and safety issues when operating ships. The semi-spade rudders have a gap between the horn/pintle and the movable wing part. Due to this gap, a discontinuous surface, cavitation phenomenon arises and results in unresolved problems such as rudder erosion. In this study, we made a rudder model for 2-D experiments using the NACA0020 and also manufactured gap flow blocking devices to insert to the gap of the model. In order to study the gap flow characteristics at various rudder deflection angles($5^{\circ}$, $10^{\circ}$, $35^{\circ}$) and the effect of the gap flow blocking devices, we carried out the velocity measurements using PIV(Particle Image Velocimetry) techniques and cavitation observation using high speed camera in Seoul National University cavitation tunnel. To observe the gap cavitation on a semi-spade rudder, we slowly lowered the inside pressure of the cavitation tunnel until cavitation occurred near the gap and then captured it using high-speed camera with the frame rate of 4300 fps(frame per second). During this procedure, cavitation numbers and the generated location were recorded, and these experimental data were compared with CFD results calculated by commercial code, Fluent. When we use gap flow blocking device to block the gap, it showed a different flow character compared with previous observation without the device. With the device blocking the gap, the flow velocity increases on the suction side, while it decreases on the pressure side. Therefore, we can conclude that the gap flow blocking device results in a high lift-force effect. And we can also observe that the cavitation inception is delayed.

• Journal of Korean Society of Forest Science
• /
• v.96 no.2
• /
• pp.227-234
• /
• 2007

The forest canopy gap has been well known as a substantial process of forest cyclic regeneration and important role in stand structure, dynamics, and biodiversity of the forest ecosystem. Based on 3,600 $5m{\times}5m$ square grids in a 9ha permanent experimental plot, the study was conducted to evaluate the regeneration pattern of woody species by developmental stage {seedlings (<1 m of height), saplingI (>1 m of height, <2 cm of DBH), and saplingII (2 cm$<200m^2$), $201-400m^2$, $400-600m^2$, $601-800m^2$, and $>800m^2$) in the mixed broadleaved-Korean pine forest. The results indicated that the regenerating trees of Populus ussuriensis occurred only in the canopy gap area, considered to be a typical gap-dependent species. The regeneration of Ulmus japonica, Ulmus laciniata, and Maackia amurensis could be generally satisfied with the gap size of $201-600m^2$, Betula costata and Prunus padus with gap size of $401-800m^2$, Picea koraiensis with gap size of $201-800m^2$, Fraxinus mandshurica and Syringa reticulata var. mandshurica with smaller than $800m^2$, respectively. Acer ukurunduense and Acer tegmentosum were likely to have no problem with the gap size to make gap regeneration. Acer mono and Tilia amurensis looked more capable of regenerating in the closed canopy disregarding the upper crown condition. The regeneration of Pinus koraiensis and Abies nephrolepis had no trouble under the canopy condition in less than $800m^2$of gap size. The density of regenerating shrubs was rather high, especially under the closed canopy, considered to be associated with great amount of regeneration production in such shade tolerant species as Lonicera maackii, Corylus mandshurica, Euonymus pauciflorus, and Philadelphus schrenkii under the closed canopy. Pearson correlation coefficient was computed to compare the similarity among non-gap area and five gap size classes by developmental stages for trees and shrubs. The similarity coefficients among closed canopy and the gap size classes were mostly significantly correlated to each other with a few exceptions.

• Journal of Labour Economics
• /
• v.30 no.2
• /
• pp.33-60
• /
• 2007

This study analyzes the trend of the gender wage gap and its sources in the Korean labor market for the years 1985-2004. Following Oaxaca and Ransom (1994), the gender wage gap is composed of the productivity-related gap and non-productivity-related gap (unobserved productivity gap and discrimination). Empirical findings indicate that both the productivity-related gap and non-productivity-related gap have dwindled, while the decline of the former far excelled that of the latter. The non-productivity-related gender wage gap is much larger for married women than for single women, possibly implying a lower unobserved productivity of married women because of their childcare responsibilities. The non-productivity-related gap is also very substantial in the male-dominated occupations as compared to the female=dominated occupations, supporting the existence of network externalities in employment.