• ETRI Journal
• /
• v.36 no.1
• /
• pp.12-21
• /
• 2014

In this paper, we propose a new digital blind in-phase/quadrature-phase (I/Q) mismatch compensation technique for image rejection in a direct-conversion receiver (DCR). The proposed image-rejection circuit adopts DC offset cancellation and a sign-sign least mean squares (LMS) algorithm with a unique step size adaptation both for a fast and precise I/Q mismatch estimation. In addition, several performance-optimizing design considerations related to accuracy, speed, and hardware simplicity are discussed. The implementation of the proposed circuit in an FPGA results in an image-rejection ratio (IRR) of 65 dB, which is the best performance with modulated signals, along with an adaptation time of 0.9 seconds, which is a tenfold increase in the compensation speed as compared to previously reported circuits. The proposed technique will be a promising solution in the area of image rejection to increase both the speed and accuracy of future DCRs.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.111-120
• /
• 2019

The output power of a crystalline silicon (c-Si) photovoltaic (PV) module is not directly the sum of the powers of its unit cells. There are several losses and gain mechanisms that reduce the total output power when solar cells are encapsulated into solar modules. Theses factors are getting high attention as the high cell efficiency achievement become more complex and expensive. More research works are involved to minimize the "cell-to-module" (CTM) loss. Our paper is aimed to focus on electrical losses due to interconnection and mismatch loss at PV modules. Research study shows that among all reasons of PV module failure 40.7% fails at interconnection. The mismatch loss in modern PV modules is very low (nearly 0.1%) but still lacks in the approach that determines all the contributing factors in mismatch loss. This review paper is related to study of interconnection loss technologies and key factors contributing to mismatch loss during module fabrication. Also, the improved interconnection technologies, understanding the approaches to mitigate the mismatch loss factors are precisely described here. This research study will give the approach of mitigating the loss and enable improvement in reliability of PV modules.

• The Journal of the Korea Contents Association
• /
• v.8 no.7
• /
• pp.1-8
• /
• 2008

In this paper, an algorithm to compensate the inter-view mismatch in the multi-view video according to the different characteristics of cameras is presented. Interview mismatches make it difficult to merge the multi-view images and decrease the coding performance. So, a preprocessing operation to compensate the mismatches is requisite in the multi-view video coding. It is shown that the mismatch in the outputs of multi-view cameras with different electro-optical transfer functions can be approximated with a linear model of a gain and an offset. In addition, a new algorithm for estimating and compensating the inter-view mismatch based on the detection of the overlapped region is presented. Experimental results using various rectified stereo images show that the proposed method compensates inter-view mismatches more accurately compared to the conventional approach.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.66-70
• /
• 2016

This paper presents an 24 GHz I/Q LO generator for a heartbeat measurement radar system. In order to improve the mismatch performance between I and Q LO signals against process variation, a 24 GHz I/Q LO generator employing a low-pass phase shifter and a high-pass phase shifter composed of inductors and capacitors is proposed. The proposed 24 GHz I/Q LO generator consists of an LO buffer, a low-pass phase shifter and a high-pass phase shifter. It was designed using a 65 nm CMOS technology and draws 8 mA from a 1 V supply voltage. The proposed 24 GHz I/Q LO generator shows a gain of 7.5 dB, a noise figure of 2.3 dB, 0.1 dB gain mismatch and $4.3^{\circ}$ phase mismatch between I and Q-path against process and temperature variations for the operating frequencies from 24.05 GHz to 24.25 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.491-499
• /
• 2018

The conventional calibration method for a noise figure analyzer is to use a noise source. This method is accompanied by a significant irregular ripple in the measurement results, because it does not consider the mismatch of the noise source and noise figure analyzer during calibration. A novel calibration method of the noise figure analyzer is proposed that considers the mismatch between the noise power and noise figure analyzer. A novel noise correlation matrix measurement technique using this method is also proposed. The method determines the noise correlation matrix and the gain of the uncorrected noise figure analyzer using uncorrected noise powers. Then, having determined the gain and noise correlation matrix, the effects of noise figure analyzers were corrected in the measurement results of the noise correlation matrix for the device under test (DUT). Through the proposed method, the measured noise parameters of a DUT showed the same degree of irregular ripples as the result of using the relative noise ratio.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.449-451
• /
• 2008

This paper studies the instability between homopolar generator and constant power load with negative impedance characteristics, provides the design method of homopolar generator system which overcomes the instability. In case of magnitude and phase of impedance of source and load mismatch, control instability of source can occur. For the safety of phase of load impedance, the gain of P, I controller with sufficient phase margin is applied through analysis on the simulation model of generator system, and the gain limit of load impedance is ensured by limitation of the gain margin of generator system. The stability of power system can be increased by considering and analyzing the impedance of source and load.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.547-555
• /
• 2008

This parer proposed the path mismatch detection and compensation algorithm with closed form for linear amplification with non-linear components(LINC) system implementation. The LINC system has a merit of using the high efficient amplifier by transferring the non-constant envelop signal which is high peak to average signal ratio into constant envelop signal. However, the performance degradation is very sensitive to the path mismatch such as an amplitude mismatch and a phase mismatch. In order to improve the path mismatch, the error detection and compensation method is introduced by the use of four test signals. Since the presented method has the closed form solution, the efficient and fast detection is available. The digital-IF structure of LINC system applied by the proposed error detection and compensation algorithm was implemented. The performance was evaluated with the IEEE 802.16 WiMAX baseband sinal which has 7 MHz channel bandwidth and 16-QAM. The Error Vector Magnitude(EVM) of -37.37 dB was obtained through performance test, which meets performance requirement of -24 dB EVM. As a result, the introduced error detection and compensation method was verified to improve the LINC system performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.54-61
• /
• 2007

A variable gain low noise amplifier (VG-LNA) implemented in TSMC 0.18 um process is presented. This VG-LNA is designed of two stage amplifier, and its gain is controlled by the shunt feedback loop composed of a gain control transistor (GCT) and a coupling capacitor in second stage. The channel resistance of GCT in the shunt feedback loop influences the input and output stages of a second stage by the Miller effect. Total gain of the proposed VG-LNA is changed by two factors, the load impedance reduction and the interstage mismatch by controlling the channel resistance of the GCT. Consequently, by adding a shunt feedback with a gain control transistor, this proposed VG-LNA achieves both wide gain tuning range of 37 dB and continuous gain control simultaneously.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.629-634
• /
• 2000

Generally, the accuracy of motion control systems is strongly influenced by both the mechanical characteristics and servo characteristics of feed drive systems. In the fed drive systems of machine tools that consist of mechanical parts and electrical parts, a torsional vibration is often generated because of its elastic elements in torque transmission. Especially, a torsional vibration caused by the elasticity of mechanical elements might deteriorate the quick movement of system and lead to shorten the life time of the mechanical transmission elements. So it is necessary to analyze the electromechanical system mathematically to optimize the dynamic characteristics of the feed drive system. In this paper, based on the simplifies feed drive system model, radius errors due to position gain mismatch and servo response characteristic have been developed and an optimal criterion for tuning the gain of speed controller is discussed. The proportional and integral parameter gain of the feed drive controller are optimal design variables for the gain tuning of PI speed controller. Through the optimization problem formulation, both proportional and integral parameter are optimally tuned so as to compensate the radius errors by using the genetic algorithm. As a result, higher performance on circular profile tests has been achieved than the one with standard parameters.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.192-197
• /
• 1992

The position error in multi-axis machine tools are due to many elements, such as the static friction, servo lag, a nonlinear disturbance, the gain mismatch between multi-axis controllers. In the work, modeling for the plant was carried out through the velocity response by the step input signal. Digital PI controllers, LQ optimal controllers and feedforward controllers are designed for a high tracking performance based on the model. The results of experimentation showed that the controllers worked properly.