• Journal of computational fluids engineering
• /
• v.11 no.1 s.32
• /
• pp.52-56
• /
• 2006

In this paper a method for analysing aerodynamic characteristics of a rotating parachute in steady descending motion is presented Because of a complex geometric configuration of the parachute associated with side vents and discontinuous skirts, special procedure was adopted to handle the geometry in the analysis. A panel method was successfully applied to the present problem and yielded good results using above procedure. A CFD code using the full Navier-Stokes equations was also applied and produced good results. Parachute free drop and wind tunnel tests were performed to determine the fully developed canopy configuration and aerodynamic characteristics. The method can be used for optimizing the parachute size and side vent configurations.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.86-87
• /
• 2011

In this paper, a conjugate heat transfer around cylinder with heat generation was investigated. Both forced convection and conduction was considered in the present finite element simulation. A finite element formulation based on SIMPLE type algorithm was adopted for the solution of the incompressible Navier-Stokes equations. We compared the finite element solution with that of Ansys fluent 12.0, in which finite volume method was employed for spatial discretization. It was found that the finite element method gave more accurate solution than Ansys fluent 12.0. Further, it was found that the maximum temperature inside cylinder is positioned at the rear side due to the flow separation.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.6-9
• /
• 2011

In this study, the two-phase incompressible flow in two-dimensional channel considering the effect of surface tension is simulated using an improved level-set method. Quadratic element is used for solving the continuity and Navier-Stokes equations to avoid using an additional pressure equation, and Crank-Nicholson scheme and linear element are used for solving the advection equation of the level set function. Direct approach method using geometric information is implemented instead of the hyperbolic-type partial differential equation for the reinitializing the level set function. The benchmark test case considers various arrays of defomable droplets under different flow conditions in straight channel. The deformation and migration of the droplets are computed and the results are compared very well with the existing studies.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.10-13
• /
• 2011

A level set method is proposed to simulate the incompressible two-phase flow considering the effect of surface tension. For reinitialization of level set junction, a direct approach method is employed, instead of solving hyperbolic type equation. A mixed element is adopted, so that the continuity mid Navier-Stokes equations are solved by using the quadratic elements (six-node triangular element mid nine-node quadrilateral element), mid the level set function is solved by using the linear elements (three-node triangular element mid four-node quadrilateral element). In order to verify the accuracy mid robustness of the codes, the present methods are applied to a few benchmark problems. It is confirmed that the present results are in good qualitative mid quantitative agreements with the existing studies.

• 한국전산유체공학회:학술대회논문집
• /
• 1997.10a
• /
• pp.86-91
• /
• 1997

This paper describes analysis of complex flow around Car-like body using Chimera grid technique. As a computational algorithm, Pullboat and Chaussee's Diagonal algorithm is selected to reduce computational time. Introducing hole points flag to this Diagonal algorithm, an algorithm for Chimera grid is generated easily. This study solves 3-D unsteady incompressible Navier-Stokes equations on a non-orthogonal curvilinear coordinate system using second-order accurate schemes for the time derivatives, and third/second-order scheme for the spatial derivatives. The Marker-and-Cell concept is applied to efficiently solve continuity equation. The fourth-order artificial damping is added to the continuity equation for numerical stability, It has concluded that the results of present study properly agree with physical flow phenomena.

• Wind and Structures
• /
• v.5 no.1
• /
• pp.15-24
• /
• 2002

This paper reports the numerical calculations of uniform turbulent shear flow around a square cylinder. The predictions are obtained by solving the two-dimensional unsteady Navier-Stokes equations in a finite volume technique. The turbulent fluctuations are simulated by the standard $k-{\varepsilon}$ model and one of its variant which takes care of the realizability constraint in order to suppress the excessive generation of turbulence in a stagnation condition. It has been found that the Strouhal number and the mean drag coefficient are almost unaffected by the shear parameter but the mean lift coefficient is increased. The present predictions are compared with available experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.66-72
• /
• 1999

A numerical simulation method has been under development for solving turbulent flows around a ship model in maneuvering motion using the Reynolds Averaged Navier-Stokes equations. The method used second-order finite differences, collocated grids, pressure-Poisson equation and four-stage Runge-Kutta scheme as key components of the solution method. A modified Baldwin-Lomax model is used for the turbulence closure. This paper presents a preliminary result of the computational study on turbulent flows past a ship model in drift motion. Calculations are carried out for a Series 60 $C_B=0.6$ ship model, for which detailed experimental data are available. The results of the present calculations are compared with the experimental data for hydrodynamic forces acting on the model as well as velocity distributions at longitudinal sections. Only fair agreements has been achieved. The computational results show the complex asymmetrical shear flow patterns including three-dimensional separations followed by formation of bilge vortices both in bow and stern regions.

• Advances in aircraft and spacecraft science
• /
• v.1 no.4
• /
• pp.399-408
• /
• 2014

The flowfields inside a contour and a conical nozzle exhausting into a straight cylindrical supersonic diffuser are computed by solving numerically axisymmetric turbulent compressible Navier-Stokes equations for stagnation to ambient pressure ratios in the range 20 to 34. The diffuser inlet-to-nozzle throat area ratio and exit-to-throat area ratio are 21.77, and length-to-diameter ratio of the diffuser is 5. The flow characteristics of the conical and contour nozzle are compared with the help of velocity vector and Mach contour plots. The variations of Mach number along the centre line and wall of the conical nozzle, contour nozzle and the straight supersonic diffuser indicate the location of the shock and flow characteristics. The main aim of the present analysis is to delineate the flowfields of conical and contour nozzles operating under identical conditions and exhausting into a straight cylindrical supersonic diffuser.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.3
• /
• pp.72-82
• /
• 1995

In the present paper, flow characteristics and free surface waves generated by a submerged hydrofoil advancing with an uniform speed are calculated. Using a numerical method based on a MAC(Marker And Cell) method, the Navier-Stokes and the continuity equations are solved to simulate flow fields around the hydrofoil. Computations are carried out in a rectangular grid system in which grids are concentrated near the foil and the free surface to improve numerical accuracies. Viscous flow phenomenas including pressure distributions are computed. Moreover, the influences of submerged depths upon the generated wave profiles and the wave breaking phenomena are also investigated. Experiments are performed at the towing tank of Inha University to measure free surface wave elevations due to the advancing hydrofoil. The computational results are compared with the present and the other available experimental data to show the accuracy of the numerical method developed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1061-1069
• /
• 2010

In this study, a simplified axisymmetric model is proposed for the problem of compressible internal flow past a microgap. Using numerical and experimental methods, the phenomena of choked flows are observed; these flows are induced by the acceleration of subsonic flows past the narrow cross-section of an annular shape made by a microgap. The relation between mass flow rate and differential pressure is obtained, and by comparing the result with experimental results, the reliability of the numerical results is discussed. The generation of a supersonic jet flow and its diffraction are visualized by performing the numerical analysis of axisymmetric compressible Navier-Stokes equations. This investigation greatly extends the physical understanding of the axisymmetric compressible flow, which has a wide range of engineering applications, e.g., in the case of valves in automotive power systems.