• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.137-137
• /
• 2000

The surface collective modes of thin K films deposited on Al(111) have been investigated using frequency dependent photoyield measurements and momentum resolved inelastic electron scattering. Jellium based theoretical calculations have predicted a richer set of features in the thin films than for the surface of a semi-infinite solid because there are th interference between two interfaces (substrate-film and film-vacuum) and heavy damping on the substrate. The use of an optical probe and electron scattering has allowed us to draw a more complete picture of the dynamic screening in thin films. The number, dispersion, damping and optical activity of the collective modes of the thin films have been measured as a function of K film thickness. New overlayer-induced excitations are observed : At qII=0, they correspond to the antisymmetric slab mode and the multipole surface plasmon. At finite qII=0, these modes undergo a transition towards the K multipole and monopole surface plasmons. With increasing coverage, the overlayer excitations turn into the collective modes of semi-infinite K. For a consistent interpretation of photoyield and electron energy loss spectra it is crucial to account for the non-analytic dispersion of the overlayer modes at small parallel wave vectors and for the finite angular resolution of the detector. The observed dispersions confirm predictions based on the time-dependent density functional approach.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.402-405
• /
• 1999

The Study of this paper is to establish the optimum fabricating condition of specimens using Vapor Deposition Polymerization Method which belongs to a mode of preparation of functional organic thin films with dry process and to develop thin film type humidity sensor which has good humidity sensitive Characteristics. Scanning electron microscopy Atomic force microscopy were used to analyze the characteristics of thin film and the basic structure of the humidity sensor is a parallel capacitor which consists of three layers of Al/PI/Al. The characteristics of fabricated samples were measured under various conditions and obtained linear characteristics in the range of 20∼80%RH independent of temperature change and low hysteresis characteristics.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.12a
• /
• pp.93-99
• /
• 1999

It is definite trend that the functional devices are to be integrated by miniaturizing of individual components. Bulk crystals turn into wafer form, while thin film of the functional materials is being fabricated for single and multi-layer devices. In addition, single crystals with multi-function performance would be desirable for further miniaturization. crystal growers have the responsibility for synthesis single crystals work to meet ever increasing requirement of future devices.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.338-343
• /
• 2015

To prevent an interfacial reaction between the anode and the electrolyte layer during the conventional high-temperature co-firing process, an anode-supported type cell with a thin-film electrolyte was fabricated by low-temperature ceramic thick film coating process. Ni-GDC cermet composite was used as the anode material and YSZ was used as the electrolyte material. Open circuit voltage and maximum power density were found to strongly depend on the surface uniformity of the anode functional layer. By optimizing the microstructure of the anode functional layer, the open circuit voltage and maximum powder density of the cell increased to 1.11 V and $1.35W/cm^2$, respectively, at $750^{\circ}C$. When a GDC barrier layer was applied between the YSZ electrolyte and the LSCF cathode, the cell showed good stability, with almost no degradation up to 100 h. Anode-supported type SOFCs with high performance and good stability were fabricated using a coating process.

• KSBB Journal
• /
• v.17 no.3
• /
• pp.235-240
• /
• 2002

The surface of polypropylene was modified by 1 keV $Ar^+$ ion beam in an $O_2$ environment in order to enhance wettability. Contact angle of deionized water on modified polypropylene was reduced from $78^{\circ}$to $22^{\circ}$. The enhanced wettability is originated from newly formed functional groups such as ether, carbonyl, and carbonyl groups. During immersion in deionized water, the enhanced wettability has remained nearly same. After washing in water, the hydrophilic functional groups on the polymer surface have been very stable. The modified polypropylene was adopted as bio-film media to remove organics in synthetic wastewater. Microbe adhesion on the polypropylene surface was improved due to the newly formed hydrophilic groups.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.3
• /
• pp.31-35
• /
• 2016

This paper demonstrates the successful application of yttria-stabilized zirconia thin films deposited by atomic layer deposition to the anode-side interlayer for cerium oxide electrolyte based solid oxide fuel cell. At the operating temperature over $500^{\circ}C$, the electrical conductivity of cerium oxide electrolyte is known to dramatically increase and, therefore, the open circuit voltage of the cell decreases leading to the decrease of the performance. Ultra-thin (60 nm) atomic layer deposited yttria-stabilized zirconia thin film in this study conformally coated the anode-side surface of the cerium oxide electrolyte and efficiently blocked the electrical conduction through the electrolyte. Accordingly, the open circuit voltage increased by up to 20%, and the maximum power density increased by 52% at $500^{\circ}C$

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.582-584
• /
• 2004

The light-emitting properties of poly(2-triethylgermyl-1,4-phenylenevinylene) (TEG-PPV) are compared with those of the silyl-substituted PPV homologue, poly(2-trimethylsilyl-1,4phenylenevinylene) (TMS-PPV). The precursor polymer is solution-processable. After carrying out thermal elimination on the precursor polymer film, the resulting fully conjugated polymer film was found to exhibit high thermal stability in air, and absorption that is shifted to the longer wavelength region owing to the extension of the n-conjugated system. TEG-PPV exhibits efficient green light emission; the maximum PL emission of a TEG-PPV thin film was found to be at 515 nm. The HOMO and LUMO energy levels were also determined using photo-emission spectroscopy. The performance of the TEG-PPV EL device was found to be comparable to that of the TMS-PPV device.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.8-15
• /
• 2018

Films with special properties (e.g., water-repellent films, optical films, anti-reflection films, and flexible films) are referred to as functional films. Recently, there has been interest in fine patterning methods for film fabrication. In particular there have been many studies that use a UV nanoimprint process involving a UV curing method. In this paper, a polymer film was fabricated by the UV nanoimprint process with a micro-pattern, and its durability was evaluated by a wear test and a nano-indentation test. The film mechanical properties (such as coefficient of friction, hardness, and modulus of elasticity) were measured. Moreover, the choice of PUA type resin used in the UV nanoimprint process was confirmed to impact the durability of the thin film. Despite making the polymer film samples using the same method and PUA type resin, different coefficient of friction, hardness, and modulus of elasticity values were obtained. PUA 4 resin had the most favorable coefficient of friction, hardness, and modulus of elasticity. This material is predicted to produce a high durability functional film.

• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.839-844
• /
• 2008

$TiO_2$ is an environment-friendly semiconducting material, and it has photocatalytic and hydrophilic effect. There are a lot of reports on the photocatalytic characteristics of $TiO_2$, such as organic pollutants resolving, anti-bacterial, and self-purification material. In this paper, $TiO_2$ micron-sized powders were deposited on the glass by room temperature powder spray in vacuum process, so called aerosol deposition (AD), and nano-grained $TiO_2$ photocatalytic thin films were fabricated. The thickness of the films were controlled by changing the number of deposition cycle. Morphologies and characteristics of the AD-$TiO_2$ thin films were examined by SEM, TEM, XRD, and UV-Visible Spectrophotometer. As the thickness of $TiO_2$ films increased, surface roughness increased. By this increment, the reaction area between film and pollutant was enlarged, resulting in better photocatalytic property.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2004.12a
• /
• pp.219-220
• /
• 2004

Superparamagnetic regions and magnetic anisotropic properties in randomly orientated Co nano dots(NDs) were investigated as a function of dot diameter, spacing, and density. The Co NDs were fabricated by intentionally exposing a laser source on ultra thin film. Various dot sizes are ultimately realized by changing laser power, scan condition, and intial film thickness. Magnetic hysteresis loops, angle-dependent magnetization, and temperature dependence magnetization of the Co NDs were measured with a superconducting quantum interference device. The analysis of magnetization and hysteresis loops was effectively used to determine superparamagnetic regions of the Co NDs. Up to now, the experimentally observed results repeal that room temperature superparamagnetic limit of our Co NDs was about 30 nm in diameter, with the confirmation of high resolution transmission electron microscope.