• Nuclear Engineering and Technology
• /
• v.34 no.5
• /
• pp.502-516
• /
• 2002

Wolsong NPP are CANDU6 type reactors and there are 4 CANDU6 type reactors in commercial operation. CANDU type reactors require on-power refuelling by two remote controlled F/Ms (Fuelling Machines). Most of channels, fuel bundles are float by channel coolant flow and move toward downstream, however in about 30% of channels the coolant flow are not sufficient enough to carry fuel bundles to downstream. For those channels a special device, FARE (Flow Assist Ram Extension) device, is used to create additional force to push fuel bundles. It has been showing that during fuelling operation of some channels the channel coolant flow rate is reduced below specified limit (80% of normal), and consequently trip alarm signal turns on. This phenomenon occurs on selected channels that are instrumented for the channel flow and required to use the FARE device for refuelling. Hence it is believed that the FARE device causes the problem. It is also suspected that other channels that do not use the FARE device for refuelling might also go into channel flow low state. The analysis revealed that the channel How low occurs as the FARE device is introduced into the core and disappears as the FARE device is removed from the core. This paper presented the FARE device behavior, detailed fuelling operation sequence with the FARE device and effect on channel flow low phenomena. The FARE device components design changes are also suggested, such as increasing the number or now holes in the tube and flow slots in the ring orifice.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.196-200
• /
• 2003

A gas chromatography/mass spectrometric assay method was developed for the simultaneous determination of ethylene glycol monomethyl ether (EGME) and diethylene glycol monomethyl ether (DEGME) in spilled aviation fuels. Ethylene glycol monobutyl ether (EGBE) and ethylene glycol monoethyl ether (EGEE) were used as internal standard and surrogate, respectively. The sample preparation consists of back-extraction with 7 mL of methylene chloride after extraction of 50 mL of fuel with 2 mL of water. The extract was concentrated to dryness and dissolved with 100L of methanol and analyzed by CC-MS (SIM). The peaks had good chromatographic properties by using semi-polar column and the extraction of these compounds from fuel also gave high recoveries of 75 and 85 % with small variations for EGME and DEGME, respectively. Method detection limits were 1.3 ng/mL for EGME and 1.0 ng/mL for DEGME in spilled fuel. The method may be useful for fuel-type differentiation between kerosene and JP-8, which may originate from the storage tank.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.16-22
• /
• 2004

Dimethyl Ether (DME) has been considered as one of the most attractive alternative fuels for a compression ignition engine. The major advantage of DME-fuelled engine is a great potential for soot-free combustion without sacrificing an inherent high thermal efficiency of diesel engine, despite a necessity for modification of the conventional fuel injection system. An experimental study on DME and conventional diesel sprays was conducted by employing a common-rail type fuel injection system with a 5-holes sac type nozzle, including a constant volume vessel pressurized with nitrogen gas. The injection rates of DME and diesel fuel were recorded with the Bosch type injection rate meter. The injection delay of DME was shorter than that of diesel fuel. The measured injection rates of DME and diesel fuel were correlated with spray penetrations. The prediction method of spray penetration was established using the injection rates, which was verified with the Dent's penetration model and found to agree well for DME case.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.27-33
• /
• 1993

Using the solenoid driven gas injection valve, Hydrogen fuel supply system was made. It was attached to a single cylinder research engine and intake port injection type hydrogen fueled S.I. engine was constructed. Engine performance, emission characteristics, and abnormal combustion were studied through the engine test performed with the variations of fuel-air equivalence ratio and spark timing. Compared with gasoline, hydrogen burns so fast that cylinder peak pressure and temperature are higher and NO is emitted more at full load condition. IN the case of intake port injection type engine, COVimep becomes lower due to the well-mixing of air and fuel, and engine output is lower owing to the low volumetric efficiency. As fuel-air equivalence ratio goes up, the combustion speed increases, and COVimep decreases. NO emission peaks slightly lean of stoichiometric. As spark timing advances and fuel-air equivalence ratio goes up, the cylinder peak pressure and temperature become higher, so abnormal combustions take place easily.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.05a
• /
• pp.62-63
• /
• 2018

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.163-170
• /
• 2002

The main objective of this study is to investigate the correlation of chemical structure and cetane number of reformed diesel fuels by ultrasonic irradiation. In order to analyze the effect of the chemical structure and the cetane number of reformed diesel fuels by ultrasonic irradiation, $^1H-NMR$ was used. From the study, following conclusive remarks can be made. 1) BI(=Branch Index), aromatics percentages, and $H_{\alpha}(={\alpha}-methyl$ functional group) of the reformed diesel fuels by ultrasonic irradiation decreased more than those of the conventional diesel fuel. 2) All the cetane numbers which were calculated from carbon type structure and hydrogen type distribution of the reformed diesel fuels increased more than those of the conventional diesel fuel. 3) Using predicated equation of cetane number caculated from carbon type structure is more reasonable than that caculated from hydrogen type distribution 4) BI, aromatics percentages, and $H_{\alpha}$ on both of conventional fuel and reformed diesel fuels by ultrasonic irradiation are inversely proportional to cetane number on these fuels.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.116-125
• /
• 2007

This article is concerned with synthesis, characterisation and electrochemical application of the mixed conducting perovskite type oxide to electrode materials for solid oxide fuel cell. First, this review provides a comprehensive survey of the various synthetic methods such as solid state reaction, Pechini, glycine nitrate process and sol-gel methods for the preparation of perovskite type oxide powders. Subsequently, the electrical and microstructural properties of the mixed conducting oxides were discussed in detail. Finally, as electrochemical applications of the mixed conducting perovskite type oxides to electrode materials for solid oxide fuel cell, fundamentals of theoretical ac-impedance model for porous mixed conducting electrodes were introduced. Furthermore, the ac-impedance behaviour of porous and dense mixed conducting electrodes prepared by various synthetic methods was discussed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.119-128
• /
• 2004

DME(Dimethyl Ether) was directly produced from the synthesis gas using the slurry phase reactor. The catalyst for DME production prepared two types (A type; Cu:Zn:Al=57:33:10, B type; Cu:Zn:Al=40:45:15, molar ratio). It was evaluated for the effect of the reaction medium oil using the small size slurry phase reactor. DME production yield and the methanol selectivity decreased in the order: n-hexadecane oil> mineral oil> therminol oil. The long-term test of DME production was carried out using A and B type catalyst, and n-hexadecane oil and mineral oil, respectively. It was confirmed that the use of A type for the catalyst and n-hexadecane for the reaction medium oil was very useful for the viewpoint of the DME production form the synthesis gas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• Journal of the Korean Institute of Gas
• /
• v.22 no.3
• /
• pp.45-52
• /
• 2018

As guidelines for exhaust gases of ship are reinforced by the International Maritime Organization, the necessity for LNG fuelled ship is emerging. The relevant research is actively progressing to develop technologies and promote commercialization. When the residual quantity of LNG fuel tank is less than 70% by consuming fuel during operation, sloshing should be considered. We applied the Type C LNG fuel tank because medium sized LNG fuelled ships are difficult to equip with re-liquefaction system. Structural integrity and thermal performance are very important, especially in LNG fuel tanks that apply to LNG fuelled ship. Through this study, we proposed evaluation procedure of thermal performance for the Type C LNG tank, and verified the validity and effectiveness of BOR(Boil-Off Rate) test Procedure by comparing and analyzing changes in temperature, pressure, BOG(Boil-Off Gas).