• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.29-34
• /
• 2009

Recently, we have a lot interest in a sudden rise of oil prices and a change weather for the earth warmming, so, development of new alternative fuels need in order to spare fossil fuel and reduce exhaust emissions for air pollution prevention. Biodiesel, which can be generated from natural renewable sources such as new or used vegetable oils or animal fats, may be used as fuel in diesel engine of compression ignition engine. In this paper, the combustion characteristics between neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were tested using four stroke, direct injection diesel engine, especially this biodiesel was produced from soybean oil at our laboratory. This analysis showed that cylinder pressures, the rate of pressure rises and the rate of heat releases were decreased as the blending ratios of biodiesel to diesel oil increased because of lower heating value of biodiesel in spite of increased oxygen content in biodiesel.

• Journal of Biosystems Engineering
• /
• v.26 no.3
• /
• pp.209-220
• /
• 2001

This study was carried out to investigate the usability of the used frying oil, which was extracted from soybean, as one of the alternative fuel of a small diesel engine. For the experiment, NO. 2 diesel oil [D], used frying oil [UF], and their volumetric blends were applied and analysis of the properties and compositions of the experimental fuels were conducted. A four cycle diesel engine with single cylinder, water cooling system, maximum output 8.1 ㎾/2,200 rpm was selected and a direct injection chamber and a precombustion chamber were attached alternately. The results obtained were as follows: 1. Engine power (BHP) were increased from 4.13~4.27㎾ to 9.08~9.15㎾ for diesel oil, from 4.05~4.19㎾ to 8.44~8.92㎾ for UF, and from 4.01~4.48㎾ to 8.69~9.16㎾ for blend fuel, as the engine speed increased from 1,000 rpm to 2,200 rpm. The BHP in case of the direct combustion chamber were fluctuated higher than those of the pre-combustion chamber. 2. With the engine speed increased, torque of the engine were increased from 39.50~40.80 N.m to 42.89 N.m, then decreased to 39.44~39.77 N.m for diesel oil, and increased from 38.73~40.04 N.m to 40.12~40.82 N.m then decreased as 36.53~38.76 N.m for UF. Torque of the blend fuels were increased from 38.75~41.76 N.m to 40.47~42.89 N.m then decreased to 37.73~39.78 N.m. There is no significant difference of torque between the type of combustion chambers. 3. The specific fuel consumption of the UF was increased about 20 percent depending on the engine speed variations. And in case of direct injection chamber, about 12 percent lower fuel consumption was observed than that of precombustion chamber. 4. NOx emission of the UF was higher than that of diesel oil at above 1,800rpm of the engine speed. In case of the direct injection chamber, NOx emission was revealed higher about 59 percent than that of the precombustion chamber, depending on the range of the engine speeds. 5. Smoke emission was decreased in case of UF compared with diesel oil on direct injection chamber. When using precombustion chamber smoke emission was a little higher than that of the direct injection chamber were showed at the engine speed range. 6. At all the engine speed range, exhaust gas temperatures were decreased 2~3$^{\circ}C$ for UF used engine compared with those of the diesel oil. The exhaust gas temperature of the direct injection chamber was higher than that of the precombustion chamber by 72$^{\circ}C$. 7. Unburnt materials remained in the cylinder in case of the pre-combustion chamber was smaller and softer than that of the direct combustion chamber. 8. The feasibility of the blend fuel B-1 and B-2 were verified as a direct combustion chamber was attached to the diesel engine, with respect to the power performance of the engine.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.311-317
• /
• 2009

To satisfy the more severe emission regulation and the demand of higher fuel economy in near future, the combustion pressure and power output of engines is going to be higher. In order to get the reduction of engine emission and the higher power, it is needed the reduction of the tension and width of ring pack. The lower tension ring and the thinner width ring can bring not only the friction reduction between the ring and liner during engine running, but also the adjustment of the blow-by gas and oil consumption by changing in the pressure in the crevice volume and the axial motion of rings togethe with the adjustment of the inter-ring crevice volumes. In this study, by using a developed basic computer proglram that predicts the blow-by gas and oil consumption of engines, it is to be examined how satisfying the level of the blow-by gas and oil consumption as being installed the piston ring pack with thinner width ring and lower tension ring.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.3
• /
• pp.269-277
• /
• 2019

Since 2020, according to the International Convention for the Prevention of Pollution from Ships (MARPOL) amended in 2016, each Administration shall transfer the annual fuel consumption of its registered ships of 5,000 gross tonnage and above to the International Maritime Organization (IMO) after verifying them. The Administration needs stacks of materials, which must not be manipulated by ship companies, including the Engine log book and also bears an administrative burden to verify them by May every year. This study considers using the Automatic Identification System (AIS), mandatory navigational equipment, as an objective and efficient tool among several verification methods. Calculating fuel consumption using a ship's speed in AIS information based on the theory of a relationship between ship speed and fuel consumption was reported in several examples of relevant literature. After pre-filtering by excluding AIS records which had speed errors from the raw data of five domestic cargo vessels, fuel consumptions calculated using Excel software were compared to actual bunker consumptions presented by ship companies. The former consumptions ranged from 96 to 123 percent of the actual bunker consumptions. The difference between two consumptions could be narrowed to within 20 percent if the fuel consumptions for boilers were deducted from the actual bunker consumption. Although further study should be carried out for more accurate calculation methods depending on the burning efficiency of the engine, the propulsion efficiency of the ship, displacement and sea conditions, this method of calculating annual fuel consumption according to the difference between two consumptions is considered to be one of the most useful tools to verify bunker consumption.

• Journal of Energy Engineering
• /
• v.14 no.2 s.42
• /
• pp.147-152
• /
• 2005

Calculation equations of fired fuel comsumption rating at boiler can lead from combustion anal-ysis and boiler heat balance using mass & energy conservations. By comparing calculation equation results with those of measurement, we can confirm the deviation of fuel consumption rate, and correction rate, and correction degree, and can also establish the proven technology to apply the equation at the site. We applied fuel rate equation to the operating power plant and recorded $2.4\%\;&\;1.5\%$ of deviation at each coal and oil fired boilers. This range of deviation is regarded as trustable to apply the fuel consumption equation to the actual site.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.2
• /
• pp.252-258
• /
• 2009

Engine bench tests has been done on a common-rail diesel engine with bio-diesel fuel to study effects of B100 and B20 on output power, fuel consumption and emissions. Test results show that B100 and B20 could reduce PM, HC, CO emission and smoke, but power decrease, fuel consumption increase and NOx increase obviously, B100 reduce PM and DS with $50%{\sim}70%$ and $80%{\sim}85%$ compared with diesel fuel, while B20 reduce PM and DS with $25%{\sim}35%$ and $30%{\sim}40%$. NOx of B100 and B20 increase $5%{\sim}20%$ compare to diesel.

• Journal of Mechanical Science and Technology
• /
• v.18 no.11
• /
• pp.2049-2057
• /
• 2004

In this study, the combustion characteristics and durability of a diesel engine using emulsified fuel was investigated. Water was used in oil type emulsified fuel. In order to understand the effect of emulsified fuel in a wide range of engine running conditions, D-13 mode was selected as a test condition, and a durability test was included to understand the long-term effect of water. Combustion pressure in a cylinder, exhaust emissions, specific fuel consumption, sound level and maximum torque were measured. NOx and PM were simultaneously reduced and the specific fuel consumption was increased and decreased at low and high loads, respectively. There was no trouble and any damage on the parts of the cylinder during a 500 hour durability test.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.3
• /
• pp.373-377
• /
• 2009

It is well known that SOx and NOx concentration has a considerable influence on the $N_2O$ emission of the greenhouse gas properties. The quantity of SOx generated during combustion, on fuel specific basis, is directly related to the sulfur content of the fuel oil. However, restricting the fuel oil sulfur content is only a partial response to limiting the overall quantity of SOx emissions, as there remains no over control on the fuel oil consumption other than the commercial pressure which have always directed the attention. This study was carried out as a new basic experiment method of emission control, manly targeted to the vessel. In the experiment, where the scrubbing was achieved through spray tower with high alkaline water made from the electrolysis of seawater, the combined action was to neutralize the exhaust gases (SOx, PM, CO etc.), dilute it, and wash it out. The results showed that SOx reduction of around 95 percent or over could be achieved when using in the high alkaline water, and also leaded to a reduction in the stability of the each pollutant components including the PM (Particulate Matter). The results suggest that the seawater electrolysis method has a very effective reduction of emissions without heavy cost, or catalysts particularly on board.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.4
• /
• pp.380-386
• /
• 2020

This paper represents an analysis of the economic impact of firing natural gas/diesel and natural gas/by-product oil mixtures in diesel engine power plants. The objects of analysis is a power plant with electricity generation capacity (300 kW). Using performance data of original diesel engines, the fuel consumption characteristics of the duel fuel engines were simulated. Then, economic assessment was carried out using the performance data and the net present value method. A special focus was given to the evaluation of fuel cost saving when firing natural gas/diesel and natural gas/by-product oil mixtures instead of the pure diesel firing case. Analyses were performed by assuming fuel price changes in the market as well as by using current prices. The analysis results showed that co-firing of natural gas/diesel and natural gas/by-product oil would provide considerable fuel cost saving, leading to meaningful economic benefits.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.7
• /
• pp.701-710
• /
• 2013

The purpose of this study is to investigate experimentally the effect of low purity methanol (LPM) on performance and smoke emission characteristics by using a four-cycle, four-cylinder, water-cooled, direct injection diesel engine with EGR system. The experiments are performed by the change of engine load in the engine load ranges of 25 to 100% with an interval of 25% under the constant engine speed of 2000 rpm. The LPM in the fuel blends contained 24.88% water by volume. The blended fuel ratios of diesel oil to LPM are maintained at 100/0, 95/5, 90/10 and 85/15% on the volume basis. In this paper, EGR rates are varied in three conditions of 0, 12.8 and 16.5%. The result shows that the brake power of a blended fuel with 15% LPM is reduced more 11.1% than that of the neat diesel oil at the full load with the EGR rate of 16.5%. At this condition, also, the brake specific fuel consumption (BSFC) is increased by 3.2%, the exhaust gas temperature is decreased by 10.7%, the smoke opacity is decreased by 18.7% and the brake thermal efficiency is increased by 7.3%. The sharp reduction of smoke opacity for a blended fuel with the LPM content of 15% at the full load without EGR system is observed by 68.4% compared with that of the neat diesel oil due to the high oxygen content of LPM.