• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.172-177
• /
• 2006

This paper presents the sliding mode observer of an induction motor for the fuel cell electric vehicles. The exact rotor flux estimation of the induction motor is important for achieving the best performance from the fuel cell electric vehicle system. However, the flux estimator of the induction motor control is highly sensitive to the voltage sensor output characteristics and system parameter variation influenced by external factors. In order to eliminate these problems, this paper investigates the electric vehicle performance due to parameter variation of the induction motor. A new method to estimate the fuel cell electric vehicle system is proposed based on the sliding mode observer.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.8
• /
• pp.585-592
• /
• 2007

Good cold start characteristics are essential for satisfactory operation of fuel cell vehicles. In this study, the melting process has been numerically investigated for a water tank used in fuel cell vehicles. The 2-D model of the tank containing ice and plate heaters was assumed and the unsteady melting process of the ice was calculated. The enthalpy method was used for the description of the melting process, and a FVM code was used to solve the problem. The feasibility study compared with other experiment showed that the developed program was able to describe the melting process well. From the numerical analysis carried out for different wall temperatures of the pate heaters, some important design factors could be found such as local overheating and pressurization in the tank.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.378-383
• /
• 2005

This experimental study presents the results of the cooling performance test of a $CO_2$ heat pump system for fuel cell vehicles. The experimental facility provides the cool ing and heating environment for cabin and heat releasing component. The test loop is designed to target the cooling capacity of 5kW and its coefficient of performance (COP) of 2.2. The cooling performance of the heat pump system is strongly dependent on the refrigerant charge and the degree of superheat. We carried out basic experiments to obtain optimum refrigerant charge and the degree of superheat level at the internal heat exchanger outlet. The heat pump system for fuel cell vehicles is different from that of engine-driven vehicles, where the former has an electricity-driven compressor and the latter has the belt-driven (engine-driven) compressor. In the fuel cell vehicle, the compressor speed is an independent operating parameter and it is controlled to meet the cooling/heating loads. Experiments were carried out at cooling mode with respect to the compressor speed and the incoming outdoor air speed. The results obtained in this study can provide the fundamental cool ing performance data using the $CO_2$ heat pump system for fuel cell vehicles.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.5
• /
• pp.490-496
• /
• 2023

Unmanned aerial vehicles (UAVs) research is recently actively underway. Especially, fuel cell battery hybrid systems are widely used to overcome the limitations of continuous operation. However, fuel cell systems must be operated in combination with a battery due to their low specific output characteristics. Therefore, a hybrid power system model for UAVs is developed. The rule-based strategy is applied to the model to properly distribute power to batteries and fuel cells. As a result, the designed rule-based power distribution control operates UAVs while maintaining battery state of charge(SOC) at an appropriate level.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.4
• /
• pp.393-404
• /
• 2014

Unmanned aerial vehicles (UAVs) have been applied to not only military missions like surveillance and reconnaissance but also commercial missions like meteorological observation, aerial photograph, communication relay, internet network build and disaster observation. Fuel cells make UAVs eco-friendly by using hydrogen. Proton exchange membrane fuel cells (PEMFCs) show low operation temperature, high efficiency, low noise and high energy density and those characterisitcs are well fitted with UAVs. Thus Fuel cell based UAVs have been actively developed in the world. Recently, fuel cell UAVs have started to develope for high altitude UAVs because target altitude of UAVs is expanded upto stratosphere altitude. Long endurance of UAVs is essential to improve effects of the missions. Improvement of UAV endurance time could be fulfilled by developing a hydrogen fuel storage system with high energy density and reducing the weight of UAVs. In this paper, research trend and analysis of fuel cell UAVs are introduced in terms of their altitude and endurance time and then the prospect of fuel cell UAVs are shown.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1213-1214
• /
• 1995

The advantages for using fuel cell instead of storages for powering electric vehicles are as follows : the energy density of fuel cell is greater than that of battery, fuel cell can be recharged much faster than battery. The objectives of this study are to investigate the status of Fuel Cell Vehicle technologies.

• New & Renewable Energy
• /
• v.1 no.4 s.4
• /
• pp.49-54
• /
• 2005

There is close relation between the heat generation in the fuel cell stack and the fuel performance. In PEM fuel cell vehicles, the stack coolant temperature is about $65^{\circ}C$, which is far lower than that for general automobile engine. Therefore, it is hard to release heat generated in the stack by using a radiator of limited size because of the reduced temperature difference between the coolant and the ambient air. In this study, indirect stack cooling system using $CO_2$ heat pump was designed and its stack cooling performance in releasing heat to the ambient was investigated. This work focuses on a series of processes that grasp the relation among the fuel cell power, the radiator capacity and the stack temperature. The purpose of this work is to find out a way to properly release sufficient amount of heat through the finite sized radiator, so that the slack power generation can not be deteriorated due to the stack temperature increase. The optimization between the compressor power consumption and the fuel cell output power can be carried out to maximize the performance of fuel cell system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.152.1-152.1
• /
• 2011

This study analyzes transitions to a green path in transportation system in South Korea. We develop transportation system model with four new technology options, green cars; Hybrid electric vehicle, plug-in hybrid vehicle, electric vehicle and fuel cell vehicle. Among those technologies fuel cell vehicle is the best option assuming no GHG emissions when driving. We use MESSAGE model to get an optimal solution of pathway for high deployment of fuel cell vehicles under the Korea BAU transportation model. Among hydrogen production sources, off gas hydrogen is most economic since it is hardly used to other chemical sources or emits in South Korea. According to off gas hydrogen projection it can run 1.8 million fuel cell vehicles in 2040 which corresponds to 10% of all passenger cars expected in Korea in 2040. However, there are concerns associated with technology maturity, cost uncertainty which has contradictions. But clean pathway with off gas and renewable sources may provide a strong driving force for energy transition in transportation in South Korea.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.545-548
• /
• 2005

There is a close relation between the heat generation in the fuel cell stack and the fuel cell performance. In PEM fuel Gell vehicles, the stack coolant temperature is about $65^{\circ}C$, which is far lower than that for general automobile engine. Therefore, it is hard to release heat generated in the stack by using a radiator of limited size because of the reduced temperature difference between the coolant and the ambient air. In this study, indirect stack cooling system using $CO_2$ heat pump was designed and its stack cooling performance in releasing heat to the ambient was investigated. This work focuses on a series of processes that grasp the relation among the fuel cell power, the radiator capacity and the stack temperature. The purpose of this work is to find out a way to properly release sufficient amount of heat through the finite sized radiator, so that the stack power general ion can not be deteriorated due to the stack temperature increase. The optimization between the compressor power consumption and the fuel cel1 output power can be carried out to maximize the performance of fuel cell system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.5
• /
• pp.484-492
• /
• 2012

The TMS(Thermal Management System) heater in a fuel cell vehicle has been developed to prevent a decline of fuel cell durability and cold start durability. Main functions of the COD(Cathode Oxygen Depletion) heater are depletion of oxygen in a cathode as heat energy and consumption of electric power for rapid warming up of a fuel cell stack. This paper covers subjects including the design specification of a heater, heater controller for detection of overheat and reliability assessment including coolant pressure cycle test of a heater. To verify the design concept, burst pressure and deformation analysis of plastic housing were carried out. Also, temperature distribution analysis of heater surface and coolant inside of housing were carried out to verify the design concept. By designing the plastic housing instead of a steel housing, the 30% weight lightening and 50% cost reduction were attained. A module-based design of a TMS system including a heater or reducing the watt density of a heater is a problem to be solved in the near future work.