• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.160-162
• /
• 2017

When rubber elastomer has contact with fuel, since the component and additive having low molecular weight can flow out, the physical properties of both elastomer and fuel could be hindered. In order to predict the life of the rubber elastomer, this study is to determine the change of weight, thickness, hardness, strain, and compression set as mechanical properties of the sealant rubber O-ring, which was dependent on volume, temperature, and storage time of the contacted fuel. We also determined purity of fuel via GC analysis and measured gross heat of combution. The results could be used as a reference to evaluate the life of the rubber elastomer.

• Clean Technology
• /
• v.19 no.4
• /
• pp.464-468
• /
• 2013

In this study, in order to increase solid content of coal water fuel (CWF), various experimental parameters (i.e., coal type, additive, particle size distribution, drying method) were evaluated. To investigate the drying method, specimen is compared to using flash dry, fluidized bed dry and oil deposit stabilized coal. Difference of the solid content between low rank coal and high rank coal in this case indicate that high rank coal exhibits more higher than 20% of the solid cotent. And specimen for dispersibility was prepared by using dispersing agent of 4 types. As a result, using the dispersing agent was shown 5% higher in sold content than the case of not using the dispersing agent. Efficiency of CWF was improved by using fine coal of 80% in the particle size distribution of coal. Result of CWF using drying methods of 3 types, oil deposit stabilized (ODS) coal dried and stabilized was effective 12% higher in sold content than raw coal.

• Journal of Hydrogen and New Energy
• /
• v.25 no.6
• /
• pp.636-642
• /
• 2014

As environment problem became a worldwide issue, countries are tightening regulations regarding greenhouse gas reduction and improvement of air pollution problems. With these circumstances, one of the renewable energies produced from biomass is getting attention. Bio-ethanol, which is applicable to SI engine, showed a positive effect on the PFI (Port Fuel Injection) type. However, Ethanol has a problem in homogeneous mixture formation because it has high latent heat of vaporization characteristics and in the GDI (Gasoline Direct Injection) type, mixture formation is required quickly after fuel injection. Particularly, South Korea is one of the countries with great temperature variation among seasons. With this reason, South Korea supply fuel additive for smooth engine operation during winter. Therefore, experimental study and investigation about application possibility of blending fuel is necessary. This paper demonstrates the spray characteristics by using the CVC direct injection and setting the bio-ethanol blending fuel temperature close to the temperature during each seasons: -7, 25, $35^{\circ}C$. The diameter and the width of the CVC are 86mm and 39mm. High-pressure fuel supply system was used for target injection pressure. High-speed camera was used for spray visualization. The experiment was conducted by setting the injection pressure and ambient pressure according to each temperature of bio-ethanol blending fuel as a parameter. The result of spray visualization experiment demonstrates that as the temperature of the fuel is lower, the atomization quality is lower, and this increase spray penetration and make mixture formation difficult. Injection strategy according to fuel temperature and bio-ethanol blending rate is needed for improving characteristics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.5
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.258-267
• /
• 2017

In this study, pitch pine (Pinus rigida, PIR) and Mongolian oak (Quercus mongolica, QUM) pellets were fabricated with bark or/and drying waste liquor (DWL) of larch (Larix kaempferi, LAK) as an additive. Based on the results of fuel characteristics of the pellets, optimal conditions for producing the high-quality pellets were provided. In the analysis of chemical composition, bark contained holocelluose and lignin of 90% and over. DWL had 0.1% solid assumed to sugars which are generated from the oven-drying of LAK logs. QUM showed high ash content (2.2%) by containing of bark in the sawdust. Bark and DWL of LAK had high ash content of 4% and over. Calorific values of all specimens and additives were higher than that of the $1^{st}$-grade standard of wood pellets designated by NIFOS (18.0 MJ/kg). PIR and QUM pellets were fabricated with additive of 2 wt% based on the solid weight of oven-dried sawdust using a piston-type flat-die pelletizer, and thus ash content and calorific value of the pellets did not affect by the use of additive. Durability of the pellets increased with the use of additive. Durabilties of pellets, which were fabricated with bark as an additive and DWL as a controller of moisture content for sawdust, did not differ from those of pellets without additives and were lower than those of pellets either with bark or DWL. However, use of both bark and DWL for the production of wood pellets might be favorable because it can make a profit from the collection process of DWL. Based on the results of fuel characteristics of the pellets, QUM and PIR pellets were produced by a flat-die pelletizer. Moisture content (MC), bulk density and durability of the pellets improved with the use of additive. Particularly, sawdust MC of 10% and the addition of bark or DWL for PIR as well as sawdust MC of 12% and the addition of bark for QUM might be optimal conditions for the production of high-quality pellets. Except for the ash content of QUM pellets, other properties of PIR and QUM pellets exceeded the $1^{st}$-grade wood pellets standards of NIFOS.

• Tribology and Lubricants
• /
• v.29 no.2
• /
• pp.117-123
• /
• 2013

Dimethyl ether (DME) has a high cetane number that is suitable for diesel fuel. DME does not contain sulfur or nitrogen, and is an oxygenated fuel so it produces no particulate matter when combusted and is environmentally friendly. DME fuel for diesel engines show excellent material properties such as a lower volumetric heating value, lower boiling point, lower lubricity, and stronger solvent effect than light oil. This study experimentally examined a lubricity improver (LI) for dimethyl ether. A diesel LI based on biodiesel and fatty acid methyl ester was tested among DME LI candidates. The long-term storage stability and physical properties of the optimum LI for DME were determined.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.419-424
• /
• 1991

In this paper, a fuel minimizing closed loop explicit inertial guidance algorithm for the orbit injection of a rocket is developed. In this formulation, the fuel burning rate and magnitude of thrust are assumed constant, and the motion of a rocket is assumed to be subject to the average inverse-square gravity, but with negligible atmospheric effects. The optimum thrust angle for obtaining the given velocity vector in the shortest time with minimizing fuel consumption is first determined, and then the additive thrust angle for targeting the final position vectors is determined by using Pontryagin's Maximum Principle. To establish the real time processing, many algorithms of the onboard guidance software are simplified. Simulations for the explicit guidance algorithm, for the 2nd-stage flight of the N-1 rocket, are carried out. The results show that the guidance algorithm works well in the presence of the maximum .+-.10 % initial velocity and altitude error. The effects of the guidance cycle time is also examined.

• KSTLE International Journal
• /
• v.3 no.1
• /
• pp.26-29
• /
• 2002

The International Lubricant Standardization and Approval Committee (ILSAC) GF-3 passenger car engine oil specification has been introduced commercially in July 2001. The new specification oil provides superior performance in terms of fuel economy, control of high temperature deposits, and oil consumption. These enhanced performances of GF-3 engine oil need high quality base oil as well as a better additive system. In this paper, the effect of base oil on various performances of ILSAC GF-3 engine oil was investigated. From the GF-3 sequence engine tests, Group III base oil shows better performance in fuel economy retention, oxidation and varnish control than combination of group III and group II or group III and group 1.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.6
• /
• pp.97-106
• /
• 1998

In this Paper, a fuel minimizing closed loop explicit inertial guidance algorithm for orbit injection of a rocket is developed. In the formulation, the fuel burning rate and magnitude of thrust are assumed constant. The motion of rocket is assumed to be subject to the average inverse-square gravity, but negligible effects from atmosphere. The optimum thrust angle to obtain a given velocity vector in the shortest time with minimizing fuel consumption is first determined, and then the additive thrust angle for targeting the final position vector is determined by using Pontryagin's maximum principle. To establish real time processing, many algorithms of onboard guidance software are simplified. The explicit guidance algorithm is simulated on the 2nd-stage flight of the N-1 rocket developed in Japan. The results show that the explicit guidance algorithm works well in the presence of the maximum $\pm$10% initial velocity and altitude errors, and exhibits better performance than the open-loop program guidance. The effects of the guidance cycle time are also examined.

• Applied Chemistry for Engineering
• /
• v.28 no.4
• /
• pp.460-466
• /
• 2017

The common petroleum can make precipitation such as a wax in a polar region due to severely cold weather condition, which can cause problems to fuel supply system. The petroleum product used in the polar region has thus been manufactured and sold suitable for the cold environment. However it is difficult to supply such petroleum products on time since these were mainly supplied abroad. In this article, the original fuel properties were first analyzed in order to find alternative fuel products for polar region. Jet fuel which is excellent cold characteristics was chosen and the fuel properties was tested by adding a constant concentration of lubricant additives to the jet fuel. As a result, the lubricant additive R621 showed the best lubricity, and adding 1000 mg/L of R621 content to the jet fuel was sufficient to enhance the lubricity. We envision that the jet fuel added 1000 mg/L of R621A can be suitable for alternative special antarctic blend diesel (SAB) in an severe polar environment.