Browse > Article
http://dx.doi.org/10.7316/KHNES.2014.25.6.636

An Experimental Study on Spray Characteristics of Directly Injected Bio-Ethanol-Gasoline Blended Fuel By Varying Fuel Temperature  

Lee, Seangwook (Department of Automotive Engineering, Kookmin University)
Park, Giyoung (Graduate School of Automotive Engineering, Kookmin University)
Kim, Jongmin (Graduate School of Automotive Engineering, Kookmin University)
Park, Bongkyu (Department of Automobile, Korea Polytechnic University)
Publication Information
Transactions of the Korean hydrogen and new energy society / v.25, no.6, 2014 , pp. 636-642 More about this Journal
Abstract
As environment problem became a worldwide issue, countries are tightening regulations regarding greenhouse gas reduction and improvement of air pollution problems. With these circumstances, one of the renewable energies produced from biomass is getting attention. Bio-ethanol, which is applicable to SI engine, showed a positive effect on the PFI (Port Fuel Injection) type. However, Ethanol has a problem in homogeneous mixture formation because it has high latent heat of vaporization characteristics and in the GDI (Gasoline Direct Injection) type, mixture formation is required quickly after fuel injection. Particularly, South Korea is one of the countries with great temperature variation among seasons. With this reason, South Korea supply fuel additive for smooth engine operation during winter. Therefore, experimental study and investigation about application possibility of blending fuel is necessary. This paper demonstrates the spray characteristics by using the CVC direct injection and setting the bio-ethanol blending fuel temperature close to the temperature during each seasons: -7, 25, $35^{\circ}C$. The diameter and the width of the CVC are 86mm and 39mm. High-pressure fuel supply system was used for target injection pressure. High-speed camera was used for spray visualization. The experiment was conducted by setting the injection pressure and ambient pressure according to each temperature of bio-ethanol blending fuel as a parameter. The result of spray visualization experiment demonstrates that as the temperature of the fuel is lower, the atomization quality is lower, and this increase spray penetration and make mixture formation difficult. Injection strategy according to fuel temperature and bio-ethanol blending rate is needed for improving characteristics.
Keywords
Fuel temperature; Ethanol; GDI; CVC; Spray characteristics;
Citations & Related Records
Times Cited By KSCI : 3  (Citation Analysis)
연도 인용수 순위
1 KAEC, "Introduction to Automotive Environment", Munundang, 2000, pp. 115-117, pp137-139, pp.201-10.
2 Y. S. KIM, "Biomass Energy in the USA: A Literature Review (3) - Bioethanol production from Biomass and Feedstock Supply", KSWST, Vol. 5, No. 1, 2007, pp. 1-10.   과학기술학회마을
3 Emmanuel Kasseris and John Heywood, "Charge Cooling Effects on Knock Limits in SI DI Engines Using Gasoline/Ethanol Blends: Part 1-Quantifying Charge Cooling," 2012 SAE International 2012-01-1275.
4 Emmanuel Kasseris and John Heywood, "Charge Cooling Effects on Knock Limits in SI DI Engines Using Gasoline/Ethanol Blends: Part 2-Effective Octane Numbers", 2012 SAE International 2012-01-1284.
5 Thomas Wallner and Richard Frazee, "Study of Regulated and Non-Regulated Emissions from Combustion of Gasoline, Alcohol Fuels and their Blends in a DI-SI Engine", 2010 SAE international 2010-01-1571.
6 S. Y. NO "Atomization Characteristics of GDI Engine", Journal of the Korean Society of Automotive Engineers, Vol. 20, No. 6, 2000.12, pp.22-29.
7 M. E. Crame, et al., "Reduce Cold-start Emission Using Rapid Exhaust Port Oxidation(REPO) in a Spark-Ignition Engine", 1997 SAE International, No.970264.
8 K. B. KIM, S. H. KANG, G. Y. PARK, J. H. SEO, Y. H. LEE, D. Y. KIM, and S. W. LEE, "A Study of Injection and Combustion Characteristics on Gasoline Direct Injection in Constant Volume Chamber", Journal of ILASS-Korea, Vol. 17, No. 3, 2012, pp. 113-120.   과학기술학회마을   DOI
9 G. Y. PARK, S. H. KANG, I. G. KIM, C. S. LIM, J. M. KIM, Y. S. CHO, and S. W. LEE, "An Experimental Study on Spray Characteristic According to Fuel", Journal of ILASS-Korea, Vol. 19, No. 3, 2014, pp.115-122.   DOI
10 N. H. KIM, J. Y. LEE, K. H. LEE, K. D. MIN, "The Study on the Effect of Fuel Properties on the Spray Characteristics of Multi-hole Injector", KSAE, 2010 Annual Conference, 2010.11, pp. 419-425.
11 A. F. Kheiralla, Mohamed M. El-Awad, Mathani Y. Hassan, Mohammed A. Hussen, and Hind I, "Experimental Determination of Fuel Properties of Ethanol/Gasoline Blends as Bio-fuel for SI engines", 2012 ICMAR, 2012.02, pp. 244-249.
12 John B. Heywood, "Internal Combustion Engine Fundamentals", McGraw-Hill, 1988, page 525-539.