• Laser Solutions
• /
• v.18 no.1
• /
• pp.12-17
• /
• 2015

This work performed numerical analysis of electromagnetic field and thermal phenomena occurring in femtosecond laser irradiation of silver nanowires. The local electric field enhancement was computed to calculate the optical energy dissipation as a Joule heating source and the thermal transport was analysed based on the two-temperature model (TTM). Electron temperature increased up to 1000K after 50fs and its spatial distribution became homogeneous after 80fs at the fluence of 100mJ/cm2. The result of this work is expected to contribute to revealing the photothermal effects on silver nanowires induced by femtosecond laser irradiation. Although the highest increase of lattice temperature was substantially below the melting point of silver, the experimental results showed resolidification and fragmentation of the silver nanowire into nanoparticles, which cannot be explained by the photothermal mechanism. Further studies are thus needed to clarify the physical mechanisms.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.2
• /
• pp.63-68
• /
• 2000

A passively mode-locked ring type fiber laser had been installed in order to get the short pulses The single and the double mode-locking were appeared, and the shortest pulse length of 65 fs was obtained with a 110 m long dispersion shifted fiber(DSF) in a local cavity of 139.8 m. Also high order harmonic modelocking of 17th and Q-switched high order harmonic modelocking were obtained.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2006.08a
• /
• pp.52-52
• /
• 2006

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.907-908
• /
• 2013

• Journal of information and communication convergence engineering
• /
• v.1 no.1
• /
• pp.39-43
• /
• 2003

The technology required to advance the state of the art of ultra-high-intensity excimer amplifier construction to the 100 J/100fs output pulse level is identified. The preliminary design work for very large final amplifier pumped by electron beam module is described, and key design problems and approaches are presented and discussed in detail based on the recent experimental and theoretical results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.7
• /
• pp.427-431
• /
• 2017

In this paper, we discuss ${\beta}-Ga_2O_3$ thin films that have been grown on freestanding GaN (FS-GaN) using furnace oxidation. A GaN template was grown by horizontalhydride vapor phase epitaxy (HVPE), and FS-GaN was fabricated using the laser lift off (LLO) system. To obtain ${\beta}-Ga_2O_3$ thin film, FS-GaN was oxidized at $900{\sim}1,100^{\circ}C$. Surface and cross-section of prepared ${\beta}-Ga_2O_3$ thin films were observed by field emission scanning electron microscopy (FE-SEM). The single crystal FS-GaNs were changed to poly-crystal ${\beta}-Ga_2O_3$. The oxidized ${\beta}-Ga_2O_3$ thin film at $1,100^{\circ}C$ was peel off from FS-GaN. Next, oxidation of FS-GaNwas investigated for 0.5~12 hours with variation of the oxidation time. The thicknesses of ${\beta}-Ga_2O_3$ thin films were measured from 100 nm to 1,200 nm. Moreover, the 2-theta XRD result indicated that (-201), (-402), and (-603) peaks were confirmed. The intensity of peaks was increased with increased oxidation time. The ${\beta}-Ga_2O_3$ thin film was generated to oxidize FS-GaN.

• Current Optics and Photonics
• /
• v.7 no.6
• /
• pp.738-744
• /
• 2023

Graphene-based saturable absorbers (SAs) are widely used as laser mode-lockers at various laser oscillators. In particular, transmission-type graphene-SAs with ultrabroad spectral coverage are typically manufactured on transparent substrates with low nonlinearity to minimize the effects on the oscillators. Here, we developed two types of transmitting graphene SAs based on CaF₂ and ZnSe. Using the graphene-SA based on CaF₂, a passively mode-locked mid-infrared Cr:ZnS laser delivers relatively long 540 fs pulses with a maximum output power of up to 760 mW. In the negative net cavity dispersion regime, the pulse width was not reduced further by inhomogeneous group delay dispersion (GDD) compensation. In the same laser cavity, we replaced only the graphene-SA based on CaF₂ with the SA based on ZnSe. Due to the additional self-phase modulation effect induced by the ZnSe substrate with high nonlinearity, the stably mode-locked Cr:ZnS laser produced Fourier transform-limited ~130 fs near 2,340 nm. In the stable single-pulse operation regime, average output powers up to 635 mW at 234 MHz repetition rates were achieved. To our knowledge, this is the first attempt to achieve shorter pulse widths from a polycrystalline Cr:ZnS laser by utilizing the graphene deposited on the substrate with high nonlinearity.

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.66-72
• /
• 1993

Additive-pulse mode-locking (APM) was performed in a $1.053{\mu}m$ cw Nd:YLF laser by coupling a nonlinear external external cavity to the main cavity. The APM pulsewidth was 4.5 ps and the average output power was 1.5 W. This APM pulse was compressed by an optical fiber and a grating pair to be as short as 210 fs with a peak power of 17 kW.

• Laser Solutions
• /
• v.11 no.1
• /
• pp.19-24
• /
• 2008

It has been recognized that laser dicing of wafers results in low mechanical strength compared to the conventional sawing techniques. Thermal shock generated by rapid thermal loading is responsible for this problem. This work presents a two-dimensional ultra-short thermo elastic model for numerical simulation of femtosecond laser ablation of metals in the high-fluence regime where the phase explosion is dominant. Laser-induced thermoelastic stress is analyzed for Ni. The results show that the laser-induced thermal shock is large enough to induce mechanical damages.

• Laser Solutions
• /
• v.11 no.2
• /
• pp.20-25
• /
• 2008

Polyimide is one of the useful materials in industry. The surface treatment of polyimide by a femtosecond laser can help accurate and fine fabrication of microstructure. And it can change the transmittance and reflectance of polyimide, too. We put femtosecond laser pulses on polyimide for rectangular or square type surface treaments and observe the change of transmittance and reflectance. Pulsewidth is 172 fs, laser power changes for fabrication are from 5 mW to 20 mW, and transmittance and reflectance are measured under 20m W, 300m W, and 920 mW. Pulse patterning is stable and almost no unwanted surface damage is shown. As power increases, working depth increases but working line width does not increase significantly. As speed changes, they also have same results. It shows the efficiency of a femtosecond laser is good and thermal damage is small for polyimide.