• 대한기계학회논문집A
• /
• 제32권12호
• /
• pp.1107-1114
• /
• 2008

This paper is aimed to understand the effect of different galvannealing temperatures on the frictional properties and Fe-Zn intermetallic phases of the galvannealed (GA) coatings on steel sheets. Their galvannealing treatments were conducted at 465, 505, 515 and $540^{\circ}C$ for about 10s in the additional heating furnace of an industrial continuous hot-dip galvanizing line. The mechanical and the frictional properties of the coatings were estimated using nanoindentation, nanoscratch, micro vickers hardness tests and flat friction tests, which were performed at contact pressures of 4, 20 and 80MPa. Also, the correlation between the microstructure and the frictional properties of the GA coatings were investigated by SEM observation for the cross-section of the GA coating after and before flat friction tests. The results showed that the mechanical and the frictional properties of the coatings are strongly dependent on their phase distributions and microstructure. Especially, in low contact pressure of 4MPa the frictional properties of the coatings were dependent on the surface phases and morphology, while in high contact pressure of 80MPa it was influenced by their mechanical properties based on the dominant phase distributions.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2003년도 춘계학술대회 논문집
• /
• pp.8-13
• /
• 2003

Frictional sound of 13 vapor permeable water repellent fabric by sound generator were recorded and analysed through FFT analysis. The frictional Sounds were quantified by calculating total sound pressure(LPT), the level range ΔL and the frequency difference Δf. Mechanical properties were measured by KES-FB. LPT values of specimens finished wet coating were higher than those of dry coating. Values for bending rigidity, shear stiffness, surface roughness and compressional recovery of polyurethane fabrics increased compared with the cire finished fabrics. Laminated fabrics had high values of frictional coefficient and low values of surface roughness. LPT showed significant correlation with compressional energy, weight and thickness. (ΔL) was highly correlated with compressional linearity, frictional coefficient, compressional recovery, and (Δf) with tensile linearity, compressional energy, thickness, and weight.

• 한국의류산업학회지
• /
• 제14권3호
• /
• pp.486-491
• /
• 2012

This study examined the sound characteristics of Taekwondo uniform fabrics to investigate the relationship between the sound parameters and the mechanical properties of the fabric as well as to provide the conditions to maximize the frictional sound of the uniform. Frictional sounds of 6 fabrics for Taekwondo uniforms were generated by the Simulator for Frictional Sound of Fabrics. The frictional speeds were controlled at low(0.62 m/s), at mid(1.21 m/s) and at high(2.25 m/s) speed, respectively. The frictional sounds were recorded using a Data Recorder and Sound Quality System subsequently, the physical sound properties such as SPL(Sound Pressure Level) and Zwicker's psychoacoustic parameters were calculated. Mechanical properties of specimens were measured by KES-FB. The SPL, Loudness(Z) values increased while Sharpness(Z) value decreased. In the physical sound parameter, specimen E had the highest SPL value at low speed and specimen B at high speed. In case of Zwicker's psychoacoustic parameters, the commercially available Taekwondo uniform fabrics(E, F) showed higher values of Loudness(Z), Sharpness(Z), and Roughness(Z), that indicates they can produce louder, shaper and rougher sounds than other fabrics for Taekwondo uniforms. The decisive factors that affected frictional sounds for Taekwondo uniforms were W(weight) as well as EM(elongation at maximum load) at low speed and WC(compressional energy) at high speed.

• 한국의류산업학회지
• /
• 제10권4호
• /
• pp.566-571
• /
• 2008

Frictional sounds of 8 vapor permeable water repellent fabrics by sound generator were recorded and analyzed through FFT fast Fourier transform analysis. The frictional Sounds were quantified by calculating level pressure of total sound(LPT), the level range(${\Delta}L$) and the frequency difference(${\Delta}f$). Mechanical properties were measured by KES-FB. LPT values of specimens finished wet coating were higher than those of other kinds of finishing. ${\Delta}L$ values of specimens laminated were highest. Absolute values of ${\Delta}f$ were high in the cire finished and laminated specimens. Values for bending rigidity, shear stiffness and energy required for the compression of coated specimens increased compared with the cire finished and laminated specimens. Laminated specimens had high values of frictional coefficient and low values of surface roughness. Relationship between frictional sounds and mechanical properties analysed by use of correlation coefficients and stepwise regression. LPT showed significant correlation with elongation, tensile energy, geometrical roughness, weight and thickness. ${\Delta}L$ was highly correlated with tensile linearity, frictional coefficient, and ${\Delta}f$ with tensile linearity, weight and thickness. LPT were revealed to be explained by elongation and weight. ${\Delta}L$were predicted by tensile linearity, and ${\Delta}f$ by tensile linearity and thickness.

• 대한의용생체공학회:의공학회지
• /
• 제22권6호
• /
• pp.519-526
• /
• 2001

At present. about 0.3 million and more THRs (Total Hip Replacement) in a rear are being done worldwide. The increase in mechanical failure with the increase in THR, required more revisions. Revisions compensate mainly the wear of the artificial joint frictional surface and the loosening of the cup and stem. According to recent researches, loosening is mainly due to wear debris UHMWPE (Ultra High Molecular Weight Polyethylene) from frictional surfaces . To overcome the wear problems associated with artificial joint materials , new surface structures with regular Patterns were designed and fabricated The lubrication Properties were examined to evaluate the wear of the frictional surfaces. The surface structure manifested a Pattern of "dents" with a 0.2-1.0 mm of diameter and 0.6-2.0 mm of Pitch. From the friction test of the SUS316L vs UHMWPE using the frictional tester, we found that the lubrication Performance was improved due to of drastically reduced amount of abrasion. There were optimum sizes for the diameter and the pitch of the Pattern. The results demonstrated that the lubrication properties could be improved by Patterning of the frictional surfaces. The surface Patterning was effective in preventing wear of the frictional surfaces, and the life of an artificial joint could be extended with such Patterning.

• Tribology and Lubricants
• /
• 제35권4호
• /
• pp.199-205
• /
• 2019

Two-dimensional materials such as graphene, h-BN, and $MoS_2$ have attracted increased interest as solid lubricant and protective coating layer for nanoscale devices owing to their superior mechanical properties and low friction characteristics. In this work, the frictional properties of single-layer graphene, h-BN, and $MoS_2$ are experimentally investigated under various normal forces using atomic force microscope (AFM) tips with a spherical and flat end, with the aim to gain a better understanding of frictional behaviors. The nonlinear relationship between friction and normal force friction was clearly observed for single-layer graphene, h-BN, $MoS_2$ specimens slid against the spherical and flat AFM tips. The results also indicate that single-layer graphene, h-BN, $MoS_2$ exhibit low frictional properties (e.g., friction coefficient below 0.1 under 70~100 nN normal force). In particular, graphene is found to be superior to h-BN and $MoS_2$ in terms of frictional properties. However, the friction of single-layer graphene, h-BN, $MoS_2$ against the flat tip is larger than that against the spherical tip, which may be attributed to the relatively large adhesion. Furthermore, it is shown that the fluctuation of friction is more significant for the flat tip than the spherical tip. The resutls of this study may be helpful to elucidate the feasibility of using two-dimensional materials as solid lubricant and protective coating layer for nanoscale devices.

• 폴리머
• /
• 제37권3호
• /
• pp.255-261
• /
• 2013

본 논문은 신발 아웃솔용 재료로 사용하기 위하여 마찰특성은 낮으나 내마모성이 우수한 부타디엔고무(BR)에 내마모성은 약하지만 마찰특성이 우수한 염화이소부틸고무(CIIR)를 블렌딩하는 경우 고무복합체의 마찰특성이 저하되는 현상을 방지하기 위한 제조방법에 대한 연구이다. BR/CIIR 복합체에서 마찰특성이 저하되지 않도록 하기 위하여 CIIR을 예비가교한 후 BR에 혼합하여 고무복합체로 제조한 경우, 복합체의 마찰특성이 현저히 향상되었다. 예비 가교한 CIIR을 40% 혼합하여 제조한 복합체의 내마모성과 마찰특성은 신발 아웃솔용으로 사용하기에 만족할 만한 값을 나타내었다.

• Tribology and Lubricants
• /
• 제14권2호
• /
• pp.10-20
• /
• 1998

In this paper, the effects of material properties on the friction and wear behavior of pure metals are investigated. The sliding material pairs are selected based on their relative compatibility and relative hardness ratio of the specimen. The initial and steady-state friction coefficients are obtained in the experiments and the wear rates are quantitatively investigated. It is shown that the initial friction coefficient is affected by the hardness ratio of sliding materials. Furthermore, in steady state condition, neither hardness ratio nor compatibility has significant influence on the frictional behavior. As for wear, the ductility of the metal affects the wear particle generation process which in turn affects the frictional behavior. The findings of this research suggest that frictional interaction cannot be simply characterized by either compatibility or hardness ratio of the materials undergoing sliding contact.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.49-55
• /
• 2009

The frictional properties of automotive brake pads with four different ceramic materials such as magnesia, hematite, alumina, and zircon were investigated. A Krauss type friction tester using gray iron disks was used to examine the friction coefficient, intensity of friction force oscillation, and the tribe-surfaces. Results showed that the friction coefficient increased as the hardness of abrasives increases. Friction oscillation was also increased with hardness of the abrasives. However, the friction materials containing less abrasive particles produced stable friction films on the sliding surface. The transition between two-body and three body abrasion during sliding also played a crucial role in destructing the friction film on the pad surface and in determining various frictional properties.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.142-149
• /
• 2002

The frictional properties of nylon can be improved by the impregnation of lubricants like wax, oil or graphite. The inclusion of these lubricants, on the other hand, decreases the mechanical properties of nylon, such as tensile strength, hardness and impact strength. As an attempt to maximize frictional properties, while minimizing a decrease in the mechanical properties, various kinds of nylon containing 3 wt% wax and varying contents of oil or graphite were prepared. It was found that the synergy effects to improve both friction and anti-wear properties is evidenced by impregnating a combination of wax/oil or wax/graphite. The wear rate of a nylon containing 3 wt% of wax and 1.5 wt% of oil turned out to be 1/4 of that of nylon impregnated with 8 wt% wax or 8 wt% oil. The latter showed the lowest wear rate among the nylons prepared with a single lubricant. In addition, the friction coefficient of the developed nylon was found to be very similar to the nylon with 8 wt% wax only.