• Fashion & Textile Research Journal
• /
• v.4 no.3
• /
• pp.273-283
• /
• 2002

In this study, the correlations of the two frictional testers have been investigated; one is the KES-FB4 system, the other is the Fabric-on-Fabric Frictional tester which was devised by authors. According to the results, the correlation between the frictional coefficients measured by the two testers has been shown highly as the load increased. But the effect of roughness of fabric surface was not dearly revealed in this study. The frictional characteristics of fabric woven from filament yarns were different with those of fabric woven from spun yarns. And, like the other materials, the effect of load on fabrics used in this experiment was related with the frictional force between two fabrics. The frictional behaviors, however, were obviously different with harder material because the frictional coefficients were not constant as the load increased.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1992.03a
• /
• pp.71-82
• /
• 1992

The frictional characteristics of Zn-Ni coated steel sheets were investigated by draw bead test and strip draw test. In strip draw test, the frictional characteristics were evaluated by the drawing force ratio (Tc/Ts) for half coating-stripped specimens. It is clarified that the drawing force ratio obtained by strip draw test is a convenient parameter compared to coefficient of friction obtained by draw bead test to evaluate the frictional characteristics of Zn-Ni coated steel sheets.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.25 no.3
• /
• pp.131-137
• /
• 2019

Carton clamps, one of forklift attachments, allow users to quickly handle shipping units such as unitized loads, large shipping cases, or crates without the requirement of pallets. As the use of palletless handling by clamp trucks increases, so does the need for simulation research on clamp truck handling. The frictional characteristics for various contact conditions of corrugated paperboards and their constituent boards were analyzed to obtain the data needed in the computer simulation for the handling of carton clamp truck. The overall mean of static-frictional coefficients between selected corrugated paperboards was 0.38 (±0.01), which was 1.3~1.6 times greater than 0.23~0.29 of the frictional coefficients between boards. The overall mean of static-frictional coefficients between the corrugated paperboards and the rubber contact pad was 0.82 (±0.02), which was about 1.1 to 2.8 times greater than 0.29~0.78 of the static-frictional coefficient between the linerboard and the rubber contact pad. The overall mean of kinetic-frictional coefficients between the corrugated paperboards was 0.35 (±0.01), and 0.76 (±0.02) between the corrugated paperboards and the rubber contact pad.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.93-99
• /
• 2005

The fault of an automobile transmission gear occurs whenever moving tooth surfaces interact. Such a failure condition has an effect on the frictional factors such as applied load, sliding speed, frictional time and gear oil. However, it is difficult to know the mutual relation of these factors. In this study, the friction and wear tests were carried out to get the friction characteristics with carburized SCM420 and nitrocarburized NT100 have being used as automobile transmission gear materials. And it was undertaken to analyze the frictional factors that have effect on frictional characteristics by using design of experiment. From this study, the result showed that the applied load in frictional factors was the most important, next to frictional time, sliding speed. And the friction characteristics of nitrocarburized NT100 was more excellent than carburized SCM420.

• Tribology and Lubricants
• /
• v.11 no.2
• /
• pp.44-55
• /
• 1995

Frictional characteristics with the change of dynamic parameters, such as stiffness, inertia and damping, in the friction measurement at dry sliding surfaces were experimentally and theoretically investigated throughout the study. Dynamic frictional force and the variation in the normal load were mainly measured at the various conditions of system dynamic parameters with which stiffness in the normal direction, loading mechanisms and test materials were varied. For the normal load, mechanisms using both a dead weight and a pneumatic cylinder were applied, which resulted in change of the inertia and damping of the test rig. Test materials were steel, rosin and PTFE, which have different types of intrinsic frictional characteristics. Test results showed that frictional characteristics under different dynamic parameters could be different even though the operating variables were the same and also they could result in the variation in the normal load, which could consequently affect the wear mechanism.

• Tribology and Lubricants
• /
• v.12 no.2
• /
• pp.55-64
• /
• 1996

Frictional characteristics with the change of loading method and normal stiffness at dry sliding surfaces were experimentally and theoretically evaluated in this study. For the study, a ball-on-disk typed test rig was built and implemented, which allowed a proper selection of loading mechanism and normal stiffness of the test rig. Loading method were varied from dead weight to pneumatic cylinder and spring loading, and the normal stiffness was varied by a spring of different stiffness. Test results showed that frictional characteristics at various loading methods were different even though the operating variables were the same. Discrepancy in the frictional characteristics, such as coefficient of friction and fluctuation in the normal load, were explained by the change in dynamic parameters of the test rigs. Results also showed that coefficient of friction, which defines as a ratio of frictional force divided a normal load, could be differently evaluated in the calculation when fluctuation in the normal load was significant.

• Journal of the KSME
• /
• v.16 no.2
• /
• pp.122-127
• /
• 1976

It was reported in the Journal of KSME Vol. 15, No. 3 and No. 4, 1975 that could be finished the best smooth surface by applying frictional work to the metal surface. Even if we can finish the best smooth surface of methal, it is not available when it has not anti-wear. Present study tried to investigate the anti-wear and the characteristics of frictional worked surface by using the sliding contact between plain bearing of brass and frictional worked jornal of mild steel. The results were compared with the case of ground journal.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.4
• /
• pp.21-26
• /
• 2006

Characteristics of texture and groove precision lapping plate are experimentally investigated by Measuring frictional forces. It is found that the frictional coefficient decreases as the embedding of diamond particles progresses. The groove precision lapping plate with concentric micro-channels indicates superior capability in embedding micrometer-sized diamond particles and uniformity in diamond embedding compared with the texture precision lapping plate with a series of circular micro-channels.

• Tribology and Lubricants
• /
• v.5 no.1
• /
• pp.21-27
• /
• 1989

A paper facirig, used for clutch disc or brake lining of the vehicles, is consisted of a combination of cellulose fiber of pulp with assorted filler and friction imparting particles, impregnated with a thermo-setting resin. In this study, as a substitution for the paper-production method, the molding-production method was attempted to produce the paper facings, and their frictional characteristics were investigated. According to the experimental results, it was estimated that the paper facings added with silica (SiO$_2$) have superior frictional characteristics, which is mused by the porosity and Mobs' hardness of the silica (SiO$_2$).

• KSTLE International Journal
• /
• v.4 no.2
• /
• pp.43-46
• /
• 2003

Water-lubricated frictional characteristics of a stainless steel ball bearings are not well known compared to the oil-lubricated frictional characteristics. Furthermore a study on friction at a high temperature is rare because the bearing maintenance strategy for water-lubricated or chemicals-lubricated bearings of equipment is generally based on the replacement of the failed bearings-and parts. Ball bearings and ball screw are installed in the power transmission for the newly developing integral reactor and these are lubricated with chemically-controlled pure water at a high temperature and a high pressure. Bearings and power transmitting mechanical elements for an atomic reactor requires high reliability and high performance during the estimated lifetime, and it should be verified. In this paper, experimental research results of the frictional characteristics for water-lubricated ball bearings are presented as a preliminary investigation.