• 한국해양공학회지
• /
• 제14권4호
• /
• pp.79-85
• /
• 2000

Press-fit pin connection is the solderless interference-fit between pins and plated through holes(PTH) in the printed curcuit board(PCB). Because of not only its simple assembly and absence of problems associated with soldering, but also its good mechanical and electrical characteristics, the press-fit pin connection technology has quickly gained wide acceptance in the telecommunications and computer industries. In this paper, the contact stress characteristics of the domestic CPF pin when inserted into the friction coefficients were compared and the stress variations of the compliant part of the pin, which have an influence on the performance, were displayed with the time and arc length after complete connected. It is supposed that the results will provide useful data to improve the performance of the pin-PCB interconnection mechanism.

• Structural Engineering and Mechanics
• /
• 제6권1호
• /
• pp.63-76
• /
• 1998

This paper presents dynamic responses of structures with sliding base which limits the translation of external loads from ground excitation. A discrete element model based on the discontinuous deformation analysis method is proposed to study this sliding boundary problem. The sliding base is simulated using sets of fictitious contact springs along the sliding interface. The set of contact spring is to translate friction force from ground to superstructure. Validity of the proposed model is examined by the closed-form solutions of an idealized mass-spring structural model subjected to harmonic ground excitation. This model is also applied to a problem of a three-story structural model subjected to the ground excitation of 1940 El Centro earthquake. Analyses of both sliding-base and fixed-base conditions are performed as comparisons. This study shows that using this model can simulate the dynamic response of a sliding structure with frictional cut-off quite accurately. Results reveal that lowering the frictional coefficient of the sliding joint will reduce the peak responses. The structure responses in little deformation, but it displaces at the end of excitation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.905-911
• /
• 2009

The viscosity drive method by the wheel which is widely used in the conventional railway systems needs a large friction force between the wheel and the guide-rail, which brings on a thrust force for a quick acceleration and a high-speed travelling. In addition, the viscosity drive method needs an increase of the vehicle weight for a large friction force. However, a maglev train is possible to be driven by the electro-magnet instead of the wheel, which produces a levitation and thrust force without any contact. In general, low-speed maglev train uses a linear induction motor(LIM) for propulsion that is operated under 300[km/h] due to the power-collecting and end-effect problems of LIM. In case of high-speed maglev train, a linear synchronous motor(LSM) is more suitable than LIM because of a high-efficiency and high-output properties. LSM has a driving principle as same as a conventional rotary synchronous motor(RSM), and the torque of RSM becomes the thrust force of LSM. A conventional LSM has relatively large air-gap compared with a conventional RSM. So, it must be achieved a design that is considered normal force by finite-asymmetric structure, end-effect on the entry and exit part, and support structure of a moving part. Therefore, in this research, authors accomplish a conceptualizing and basic design of a small-scaled LSM, and characteristics analysis using FEM.

• 대한화학회지
• /
• 제19권1호
• /
• pp.43-49
• /
• 1975

소량의 요오드 화합물이 윤활류에 함유될 때 금속표면사이의 마찰을 감소시키고 내마모성을 향상시키는데 이는 금속표면에 박층상구조의 이요오드화물이 형성되기 때문이라고 한다. 그러나 금속표면에서의 화학반응성, 마모와 극압실험 및 hot wire method에 의한 결과에 의하면 윤활기구는 이 요오드화물의 박층상 구조가 아니고 다른 기구에 의한 것임을 알았다. 유기 요오드화합물중에서 특히 N-iodopyridinium dichlorodate는 double charge transfer complex로써 다른 methyl iodide계의 화합물 보다 금속표면 사이의 마찰을 더욱 감소시키고 윤활기구는 interhalogen의 화학반응에 의한 것임을 알았다.

• 소성∙가공
• /
• 제23권7호
• /
• pp.439-445
• /
• 2014

Changes in the accuracy of the geometrical shape after a surface treatment are often very large due to the variation of the deformation mechanisms such as edge draw-in and the variation in springback caused by the reduction in the coefficient of friction between the tool and the blank. In the present study, the resulting shape accuracy due to the changes in deformation is quantitatively examined in order to predict the variation and to remove any undesirable additional tool compensation for the center pillar member made from steel with a UTS of 980MPa. The study examines important process parameters that are closely related with the edge draw-in such as the blank holding force, the contact status between the tool and the blank and the friction coefficient. The proposed method is applied within the finite element analysis of the stamping process for tools after a surface treatment and the amount of edge draw-in and flush values are compared between the analysis and experiments. The results demonstrate that the proposed quantification and finite element scheme are applicable to complicated tool compensation procedures and compensation can be designed effectively.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.190-196
• /
• 2005

The power steering hose assembly is usually manufactured through the swaging process, which is conducted to connect a hose with metal fittings. In this process the hose is inserted into metal components, the sleeve and the nipple, and compressed in the radial direction by the jaws to clamp the hose with metal components. In case that the clamping force is small, the oil in the hose can leak locally under the severe operating conditions. To confirm the clamping force requirements, the measurement of separation force in longitudinal direction of the hose is usually performed. In this study, the swaging process of a hose is simulated with the finite element method, to investigate the effect of friction coefficient on the separation fDrce. The results interpretations are ffcused on the inner rubber component, and also a formula is proposed to estimate the separation farces with respect to friction coefficients.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.406-413
• /
• 2000

The friction and wear behaviors of Magnetron Sputtered MoS$_2$films were investigated by using a pin on disk type tester which was designed and manufactured for this experiment. The experiment was conducted by using silicon nitride (Si$_3$N$_4$) as a pin material and Magnetron Sputtered MoS$_2$on bearing steel (STB2) as a disk material, under operating conditions that include different surface roughness (Polishing specimen, Grinding specimen)(2types), linear sliding velocities in the range of 22, 44, 66mm/sec (3types), normal loads vary from 9.8N, 19.6N, 29.4N(3types), corresponding to contact pressures of 1.9∼2.7GPa and atmospheric conditions of high vacuum( 1.3${\times}$10$\^$-4/Pa), medium vacuum( 1.3${\times}$10$\^$-l/Pa), ambient air(10$\^$5/Pa)(3types). We investigated fracture mechanism in magnetron sputtered MoS$_2$films with Magnetron Sputtering method in each experiment.

• 터널과지하공간
• /
• 제2권2호
• /
• pp.212-223
• /
• 1992

The distinct element method(DEM) si well suited to the kinematic analysis of blocky rock masses. Two distinctive problems, a rock avalache and tunnel in jointed rock masses, are chosen to apply the DEM which is based on perfectly rigid behaviour of blocks. Investigated for both problems are the effects of the input parameters such as contact stiffnesses, friction coefficient and damping property. Using various types of models of the avalanche and tunne, an extensive parametric study is done to gain experiences in the method, and then to alleviate difficulties in determining parameter values suitable for a given problem. The coefficient of frictio has significant effects on all aspects of avalanche motion(travel distance, velocity and travel time), while the stiffnesses affect the rebounding and jumping motions after collision. The motion predicted by the models having single and mutiple blocks agrees well to the observations reported on the actual avalache. For the tunnel problem, the behaviour of the key block in an example tunnel is compared by testing values of the input parameters. The stability of the tunnel is dependent primarily on the friction coefficient, while the stiffness and damping properties influence the block velocity. The kinematic stability of a tunnel for underground unclear waste repository is analyzed using the joint geometry data(orientation, spacing and persistence) occurred in a tailrace tunnel. Allowing a small deviation to the mean orientation results in different modes of failure of the rock blocks around the tunnel. Of all parameters tested, the most important to the stability of the tunnel in blocky rock masses are the geometry of the blocks generated by mapping the joint and tunnel surfaces in 3-dimensions and also the friction coefficient of the joints particularly for the stability of the side walls.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.604-609
• /
• 2001

In the sheet metal forming process, the drawbead is used to control the flow of material during the forming process. The drawbead provides proper restraining force to the material and prevents defects such as wrinkling or breakage. For these reasons, many studies for designing the effective drawbead have been conducted. For the analysis, the numerical method called the static-explicit finite element method was used. The finite element analysis code for this method has been developed and applied to the drawbead process problems. In result, convergence problem and computation time due to large non-linearity in the existing numerical analysis methods were no longer a critical problem. Futhermore, this approach could treat the contact friction problem easily by applying very small time intervals. It is expected that various results from the numerical analysis will give very useful information for the design of tools in sheet metal forming process.

• 한국산학기술학회논문지
• /
• 제6권6호
• /
• pp.536-541
• /
• 2005

고무 성분에 대한 대변형 및 강성은 비선형 및 대변형의 해석 결과로 나타낼 수 있다. 또한 고무는 Mooney-Rivlin의 모델로서 적용되고 고무들 사이에서 자기 접촉이 성립되어지는데 강성체 및 고무 사이에서는 마찰력이 있게 된다. 본 연구에서 사용된 비선형 시뮬레이션 해석은 여러 가지의 고무 성분들의 설계, 분석 그리고 개발에 널리 사용될 수 있다. 이러한 방법을 이용하면 새로운 고무 제품을 개발하는데 있어서 시간과 비용을 절감할 수 있을 것으로 보인다. 고무 성분들의 분석은 특이한 재료의 모델링과 비선형 유한 요소 해석을 요하는데 금속 부품들에 대하여 해석하는 프로그램들과는 완전히 다르다. 본 연구의 목적은 대변형 및 비선형의 고무 부품을 해석하는데 있다.