• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.13-18
• /
• 2001

In this paper, FFT(Fast Fourier Transform) analysis of friction was suggested as a method to interpret the contact conditions. Micro-grooves with various dimensions were fabricated on the silicon surface to investigate the frictional behavior with respect to the change in geometrical contact condition. Frictional forces between micro-grooved surfaces and spheres modeled as surface asperities were measured using a micro-tribotester which was built inside a SEM(Scanning Electron Microscope). The experimental results show that the relative dimensions and distributions of contact asperities between two surfaces can be predicted by the power spectrum and the main frequency in FFT-based analysis of friction coefficient. Also, it was shown that the friction coefficient for multi-asperities was the result of the superposition of that for each asperity.

• 한국소음진동공학회논문집
• /
• 제14권9호
• /
• pp.837-845
• /
• 2004

A variable friction damper for vehicle driveline has been proposed. This new torsional damper system uses a solenoid as an actuator to vary friction force of the damper. To verify the idea of using a solenoid in a variable damper system, the test fixture and the dampers are made and tested. Also, to find out the range of damper friction forces that influence the vehicle driveline vibration, a mathematical model of the driveline had been developed and simulated. Test and simulation results show that, within electric current used in the vehicle electric system, the solenoid can develop enough friction force that will surpass resonance in the driveline of 1.5 L Gasoline engine vehicle during acceleration.

• 한국군사과학기술학회지
• /
• 제3권2호
• /
• pp.231-243
• /
• 2000

This paper describes a simulation of secondary motion of piston assemblies using PISDYN by Ricardo. Motions of the piston, pin, rod and skirt are separately calculated, by integrating equations of motion for individual components and dynamic degrees of freedom. The effects of engine speed at full load and pin offsets on the piston assembly secondary motions, forces and friction were investigated in parametric study for 4-cylinder gasoline engine. Results show that lateral displacement and friction loss of the piston increase as a function of engine speed. The lateral motion of the piston is affected by the change in pin offset. The minimum friction loss for the condition of 4800rpm WOT occurs at a pin offset of 1.6mm.

• 대한안전경영과학회지
• /
• 제4권2호
• /
• pp.237-249
• /
• 2002

A cutting fluid can improve machining quality and tool life by maintaining the tool toughness and by providing a lubrication effect to reduce the friction between the chip and tool interface. Although liquid nitrogen as an environmentally safe coolant has been widely recognized in cryogenic machining, its function as a lubricant is plausible due to its chemical inertness, physical volatility and low viscosity. Since a reduced friction is a direct witness of the lubrication effect from a tribological viewpoint, this paper presents an evaluation of the apparent friction coefficient on the tool-chip interface in cryogenic cutting operations to prove and characterize the lubricity of LN2 in cryogenic machining. The mathematical approaches have been formulated to derive the normal and frictional forces on the tool-chip interface for the oblique cutting tests.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.30-36
• /
• 2019

The tribological properties of paper-based friction materials are crucial to the performance of a wet clutch system. In this work, the friction and wear characteristics of a paper-based friction material in boundary lubrication state was experimentally investigated using a pin-on-reciprocating tribotester under various normal forces and temperatures. It was found that the wear rate of the friction material increased from $5.8{\times}10^{-6}mm^3/N/cycle$ to $5.5{\times}10^{-5}mm^3/N/cycle$ after 1,700 cycles of testing at $80^{\circ}C$ as normal force increased from 2 N to 7 N. The friction coefficient was also found to increase from 0.135 to 0.155 with increasing normal force from 2 N to 7 N. The increase in contact pressure with increasing normal force may be responsible for these results. In addition, as temperature increased from $20^{\circ}C$ to $80^{\circ}C$, the wear rate of the friction materials increased from $2.0{\times}10^{-5}mm^3/N/cycle$ to $3.6{\times}10^{-5}mm^3/N/cycle$ while the friction coefficient decreased from 0.163 to 0.146. This result may be associated with the decrease in the hardness of friction materials with increasing temperature. Furthermore, plastic deformation on the friction materials was mainly observed after the test. The outcome of this work may be useful to gain a better understanding of the tribological properties of friction materials, and therefore can contribute to the development of friction materials with enhanced performance for wet clutch systems.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2000년도 추계 학술논문발표회 논문집
• /
• pp.442-449
• /
• 2000

In railway structure, long rail causes the increase of stress. Especially, additional stress and displacement are caused by the discontinuity and variations of the stiffness of substructures in the section of bridges. In the other words, binding forces like the connection strengths and friction force between ties and ballasts play the role of resistance forces.(omitted)

• 한국운동역학회지
• /
• 제12권2호
• /
• pp.361-380
• /
• 2002

마찰력(friction)은 급정지나 급출발, 또는 두 동작이 동시에 이루어질 때, 미끄럼방지는 효과적으로 이루어져야 하며, 특히 테니스, 농구, 배구 등 코트 스포츠에 있어서 최적의 마찰력은 필수적이다. 이러한 마찰력은 무게가 많이 나갈수록, 다른 물체와의 접촉면이 넓을수록, 장력이 클수록 커진다. 또한 표면이 매끄러울 때보다는 거칠수록 커지는 특성을 가지며, 본 연구의 목적은 테니스화겉창과 테니스코트에 설치되어 있는 스토츠바닥재사이에 마찰력을 대해서 고찰해 보고자 하였으며, 마찰력운동 및 이의 관련 선행 국외 연구활동이 어떻게 이루어졌는지를 종단적 국외문헌조사를 통해 어떤 상관관계가 있는지를 구명해 보고자 하였다. 국내 테니스화의 연구와 테니스스포츠바닥재간의 국외 연구활동의 종단적 연구지표로서 스포츠와 스포츠바닥재간의 마찰력 관련주요연구연표를 작성해 봄으로서 연구활동의 경과추이를 조사하였다. 테니스 바닥재 현황으로는 테니스코트의 표층재는 일반적으로 천연재료를 사용한 클레이계코트와 합성재료를 사용한 전 천후계 하드코트로 구별된다. 본 연구를 통하여 테니스화 겉창과 테니스 스포츠바닥재간의 마찰력의 국외선행연구현황 이해를 돕고, 향후 국내에서 스포츠화 겉창과 마찰력, 스포츠바닥재와 마찰력의 평가에 대한 연구시 국외에서 기 실시된 연구를 중복연구하는 시행착오 방지 및 국외 선행연구에 대한 기초자료 및 연구현황을 자세히 파악할 수 있을 것으로 사료된다.

• 대한기계학회논문집B
• /
• 제29권11호
• /
• pp.1189-1198
• /
• 2005

Direct numerical simulations were performed to investigate the physics of a spatially developing turbulent boundary layer flow subjected to spanwise oscillating electromagnetic forces in the near wall region. A fully implicit fractional step method was employed to simulate the flow. The mean flow properties and the Reynolds stresses were obtained to analyze the near-wall turbulent structure. It is found that skin friction and turbulent kinetic energy can be reduced by the electromagnetic forces. The decrease in production is responsible fur the reduction of turbulent kinetic energy. Instantaneous flow visualization techniques were used to observe the response of streamwise vortices and streak structures to spanwise oscillating forces. The near-wall vortical structures are affected by spanwise oscillating electromagnetic forces. Following the stopping of the electromagnetic force, the flow eventually relaxes back to a two-dimensional equilibrium boundary layer.

• 대한치과교정학회지
• /
• 제28권1호
• /
• pp.123-133
• /
• 1998

TiN ion-plating된 Co-Cr 선재(.016", .016"x.022")와 ion-plating되지 않은 선재(.016", .016"x.022")를 이용하고, 3 가지 종류의 브라켓(TiN ion-plating된 금속 브라켓, 세라믹 브라켓 및 플라스틱 브라켓)을 대상으로 마찰실험을 행하고, 거기에서 얻어진 마찰 특성곡선과 곡선으로부터 구한 최대 정지마찰력, 그리고 선재와 브라켓의 표면양상을 주사전자현미경으로 관찰하여 TiN ion-plating의 효과를 검토한 결과 다음과 같은 결론을 얻었다. $\cdot$3가지 종류의 브라켓에 TiN ion-plating된 선재를 사용한 경우의 마찰력은 TiN ion-plating되지 않은 선재를 사용한 경우의 마찰력보다 각각 통계학적으로 유의성있게 낮았다(p<0.05). $\cdot$3가지 종류의 브라켓에 원형 선재를 사용한 경우의 마찰력은 각형 선재를 사용한 경우의 마찰력보다 각각 통계학적으로 유의성있게 낮았다(p<0.05). $\cdot$원형 선재를 사용한 경우 TiN ion-plating되지 않은 선재를 사용한 경우가 TiN ion-plating된 선재를 사용한 경우보다 선재 및 브라켓 슬롯의 표면이 더욱 거친 양상을 나타내었다. $\cdot$각형 선재를 사용한 경우 전반적으로 원형 선재를 사용한 경우보다 선재 및 브라켓 슬롯의 표면이 더욱 거친 양상을 나타내었다. $\cdot$TiN ion-plating된 원형 선재를 사용한 경우 정지마찰력과 운동마찰력의 차는 별로 없었으나 TiN ion-plating된 각형 선재를 사용한 경우 정지마찰력은 운동마찰력보다 다소 높았다. $\cdot$TiN ion-plating되지 않은 선재를 사용한 경우가 TiN ion-plating된 선재를 사용한 경우에 비해 정지마찰력이 운동마찰력보다 휠씬 높았다.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.267-272
• /
• 2002

Nano adhesion between SPM(scanning probe microscope) tips and DDPO$_4$(octadecylphosphoric acid ester.) and ODPO$_4$(octadecylphosphoric acid ester) SAM(self-assembled monolayer.) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes with the applied normal load. DDPO$_4$ and ODPO$_4$ SAM were formed on Ti and TiOx surfaces. Ti and TiOx were coated on the Si wafer by ion sputtering. Adhesion and friction of DDPO$_4$ and ODPO$_4$ SAM surfaces were compared with those of OTS(octadecyltrichlorosilane) SAM and DLC surfaces. DDPO$_4$ and ODPO$_4$ SAM converted the Ti and TiOx surfaces to be hydrophobic. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare surfaces. Work of adhesion was also discussed to explain how the surface was converted into hydrophobic Results also showed that tribological characteristics of DDPO$_4$ and ODPO$_4$ SAM had good properties in the adhesion, friction, wetting angle and work of adhesion. DDPO$_4$ and ODPO$_4$ SAM could be one of the candidates for the bio-MEMS elements.