• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.551-552
• /
• 2008

This paper presets a results of frequency response in variation of wire bonding length. A gold ball bonding is used as a wire bonding process, and a DPDT(double pole double thru) switch is adapted as a device for test. Wire length is ranged from 442um to 833um and a measured frequency range is from 1 GHz to 6 GHz. Little difference are measured in insertion loss and return loss depending on wire length. Measured S21 and S11 are -0.58 dB and -17.7 dB, respectively. S21 insertion loss is rising up and S11 insertion loss is falling down as the frequency is increased.

• 설비공학논문집
• /
• 제12권7호
• /
• pp.649-658
• /
• 2000

Thermodynamic modeling of low-pressure scroll compressor was developed by combining continuity and energy conservation equation. Suction gas heating was considered using energy balance inside the low pressure shell. Pressure, temperature and mass of refrigerant-22 as a function of orbiting angle were calculated by solving the governing equations using fourth order Rung-Kutta scheme. Motor efficiency was taken by experiments with a variation of frequency. The developed model was applied to the analysis of an inverter driven scroll compressor with a variation of frequency, pressure ratio and operating conditions. The model was verified with the experimental results at the same operating conditions. The developed model was adequate to predict performance of the inverter driven scroll compressor as a function of operating conditions. Calculated parameters from the model were discharge temperature, mass flow rate, power input, COP, and thermodynamic properties with respect to orbiting angle. To enhance the performance of a scroll compressor, it is essential to diminish leakage at low frequency level and improve the mechanical efficiency at high frequency level.

• 한국세라믹학회지
• /
• 제23권3호
• /
• pp.21-26
• /
• 1986

In this study the system of $Pb(Mn_{1/3} Nb_{2/3})O_3-PbTiO_3-PbZrO_3$ piexoelectric ceramics was made in the radial mode disk and attenuation characteristic of the desinged ladder type filter was investigated. What is more temperature dependance of resonant frequency and variation of resonant frequency was examined by chan-ging the electrode diameter of piezoelectric resonator. (A Group : De=11mm, B Group : De=7.5mm and C Gro-up : De=5.5mm) Upon investigation it was the following. The center frequency of A, B and c filter showed up in the 200KHz, 270KHz and 380KHz respectively. As the electrode diameter decreased center frequency in creased abruptly. As the Co_2/Co1 increased attenuation characteristics and selectivity was improved. As the x=50. resonant frequ-ency invaried with variation of temperature.

• 대한전기학회논문지
• /
• 제33권9호
• /
• pp.355-363
• /
• 1984

An ideal and an approximate eauivalent circuits of a face-mounted PZT piezoelectric transformer were introduced from the equivalent circuit taking into account the mechanical loss of a PZT piezoelectric disk vibrator. And several expressions for the resonant frequencies and for the voltage ratios were derived from the approximate circuit of the transformer. From the experiments on the vltage ratios regarding the frequency variation without load and on the load variation at resonant frequency, it was found that the voltage ratio increased with the increase of load resistance and decreased sharply with the slight deviation from the resonant frequency, and that no-load voltage ratio at the resonant frequency was proportional to the product of the mechanical quality factor and the square of the electromechanical coupling factor of the vibrator.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.717-718
• /
• 2013

CMOS로 구성된 전압-제어 발진기의 채널 폭과 길이가 변화하면, 입력 전압에 따른 출력 주파수가 변화할 것이다. 본 논문에서는 FLL(Frequency Locked Loop) 회로의 구성 요소로 사용되는 전압-제어 발진기의 채널 폭 변화에 따른 전기적인 특성 변화를 시뮬레이션을 통하여 살펴보고자 한다. 그리고 변화하는 채널 폭에 따른 전압-제어 발진기의 신뢰성 특성을 향상하기 위한 방안을 살펴보고자 한다.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.18-26
• /
• 2016

This paper proposes a compensation algorithm for reducing a specific ripple component on synchronous reference frame phase locked loop (SRF-PLL) in grid-tied single-phase inverters. In general, SRF-PLL, which is based on all-pass filter to generate virtual voltage, is widely used to estimate the grid phase angle in a single-phase system. In reality, the estimated grid phase angle might be distorted because the phase difference between actual and virtual voltages is not 90 degrees. That is, the phase error is caused by the difference between cut-off frequency of all-pass filter and grid frequency under grid frequency variation. Therefore, the effects on phase angle and output current attributed to the phase error are mathematically analyzed in this paper. In addition, the proportional resonant (PR) controller is adapted to reduce the effects of phase error. The validity of the proposed algorithm is verified through several simulations and experiments.

• 한국정보전자통신기술학회논문지
• /
• 제2권2호
• /
• pp.29-36
• /
• 2009

비선형적인 위상 변화를 지닌 비정상(non-stationary)신호는 레이더(Radar), 통신(telecommunication), 생체공학, 지질탐사, 음향 등 여러 분야에서 쉽게 접하는 신호이다. 비정상신호는 일반적으로 시간에 따라 신호의 물리적 특성이 변화하는 신호를 의미하며, 순간 주파수는 신호의 특정시간에 해당하는 신호의 주파수를 의미한다. 이 논문에서는 순간 주파수를 결정하기 위한 연속 웨이브렛 변환의 적용에 대하여 논하였다.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.157-164
• /
• 2003

The pulse-echo method is one of the most widely used ultrasonic techniques for application of nondestructive evaluation. Particularly, quantitative nondestructive evaluation of defects has been considered more important to assure the reliability and the safety of structure. Frequency energy in adhesive joints is based on the ultrasonic wave analysis. The attenuation coefficient upon wave amplitude and the frequency energy that is expressed in the term of wave pressure amplitude were utilized for the primary wave experiment. By means of a control experiment, it was confirmed that the variation of the frequency energy in adhesive joints depends on transition by stress variation. In this paper, the ultrasonic characteristics were measured for single lap joint and Double Cantilever Beam specimen with different fracture modes that was subjected to stress. Consequently, the data that was obtained from the adhesive specimen was analytically compared to the fracture mechanics parameter

• 디지털산업정보학회논문지
• /
• 제10권2호
• /
• pp.37-45
• /
• 2014

This paper is a study of the water sensor using a coaxial cavity resonator. This water sensor uses the resonant frequency variation of the coaxial cavity resonator when there is a water drop of the used coaxial cavity resonator. And we made resonant frequencies by controlling the input voltage of the oscillator which will be mainly resonated in the coaxial cavity resonator. First, we made the coaxial cavity resonator by simulating the resonator structure with the proposed size and we expect the resonant frequency from the simulation and then we decide the VCO from the result. Second, we made the water drop detecting sensor circuit and measured the water sensor. We decided the size of the resonator as inner conductor 5mm, outer conductor 14mm, the height of resonator 9.5mm, and the height of the glass 6mm from the simulated result. The simulated resonant frequencies are 3.09GHz and we made the VCO frequency ranges from 2.56GHz to 3.2GHz. The measured resonant frequency is 2.97GHz and the return loss is under -8. 4 dB at the center frequency. When the water is dropped on the glass of the resonator, the voltage has changed from 690mV to 145mV. It shows the proposed water sensor can detect the water by the resonant frequency variation of the resonator.

• 한국소음진동공학회논문집
• /
• 제24권7호
• /
• pp.569-574
• /
• 2014

In order to investigate low frequency swishing noise of wind turbines, acoustic source model using a singularity in circular motion is introduced to derive analytic solution of Lowson acoustic analogy in time domain. Results in time and frequency domains computed by the solution show apparent modulation of amplitude and frequency. The solution indicates that time histories of acoustic pressure at receiver points varied significantly according to receiver's directional location, even when the retarded time distributions are similar. However, the corresponding time-averaged spectra of sound pressure at the receiver locations where the retarded time distributions are almost same are not significantly different. It can be inferred from these results that the time-averaged sound pressure spectra which cannot take into account the detailed difference in the time-variation of wind turbine noise may not represent the sound quality of wind turbines due to its swishing. Finally, as an introduction of procedure to quantify low frequency swishing noise level, relative variation of overall sound pressure level is obtained using tonal low frequency noise model.