• Structural Engineering and Mechanics
• /
• 제84권6호
• /
• pp.823-829
• /
• 2022

This study considered the experimental parameters (Nano-graphene oxide reinforced polycarbonate, GFRP) under low-velocity impact load and vibration analysis. The effect of nano-graphene oxide (NGO) on a polycarbonate-based composite was studied. Two test procedures were adopted to obtain experimental results, vibration analysis. The mechanical tests were performed on damaged and non-damaged specimens to determine the damaging effect on the composite specimens. After the test was carried out, the effect of NGO was measured and damping factors were ascertained experimentally. 0. 2 wt% NGO was determined as the optimum amount that best affected the Vibration Analysis. The experiments revealed that the composite's damping properties were increased by adding the nanoparticles to 0.25 wt% and decreased slightly for the specimens with the highest nanoparticles content. Cyclic sinus loading was applied at a frequency of 3.5 Hz. This paper study the frequency effect of 3.5khz frequency damage on mechanical results. Found that high frequency will worthlessly affect the fatigue life in NGO/polycarbonate composite. In 3.5 Hz frequency, it was chosen to decrease the heat by frequency. Transmission electron microscopy (TEM) micrographs were used to investigate the distribution of NGO on the polycarbonate matrix and revealed a homogeneous mixture of nano-composites and strong bonding between NGO and the polycarbonate which increased the damping properties and decreased vibration. Finally, experimental modal analysis was conducted after the high-velocity impact damage process to investigate the defect on the NGO polycarbonate composites.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1993년도 추계학술대회
• /
• pp.67-70
• /
• 1993

This preliminary study describes the self-mixing effect of laser diode for the measurement of tissue blood flow. A self-mixing effect of laser diode was detected by the single-mode laser diode and the moving target, and the Doppler shifted frequency was thanked linearly with the driving frequency of speaker. The measured Doppler shifted frequency was compared with the simulated data.

• 인지과학
• /
• 제20권3호
• /
• pp.335-355
• /
• 2009

위험정보를 확률이나 빈도양식으로 제시하고 질병으로 사망할 확률(기저율)에 대한 위험을 판단하게 하고 양성판정을 받은 사람이 질병에 걸렸을 확률(사후확률)에 대한 위험판단과 추론의 정확성을 비교하였다. 베이스 추론 과제를 사용한 연구 1에서 숫자양식의 효과가 관찰되었다. 참가자들은 위험이 확률보다는 빈도로 제시될 때 더 위험하다고 판단하였고 질병에 걸렸을 확률을 더 정확하게 추론하였다. 빈도의 범위가 좁을 때보다 넓을 때 더 위험하다고 판단하는 효과는 관찰되지 않았다. 분석적 사고체계가 위험판단에 미치는 영향을 검토하려고 사후확률을 계산하는 조건과 계산하지 않는 조건을 비교하였다. 숫자양식의 효과는 여전히 관찰되었다. 연구 2는 기저율과 사후확률의 크기에 따라 숫자양식 효과와 빈도범위 효과가 달라지는지 알아보았다. 숫자양식의 효과는 기저율과 사후확률의 크기에 상관없이 모든 조건에서 관찰되었다. 위험한 사건이 발생할 확률의 높고 낮음에 상관없이 빈도로 제시되었을 때 참가자들이 더 위험하다고 판단하였다. 그러나 빈도범위 효과는 기저율이 낮은 조건에서만 발견되었다. 본 연구의 결과들을 이중처리체계 이론과 관련시켜 논의하였다.

• 전기학회논문지P
• /
• 제62권1호
• /
• pp.45-49
• /
• 2013

High frequency system has been used for the purpose of skin care and obesity treatment, by high-frequency energy is applied to the human body generates deep heat. Conventional high frequency system could not selection control by depending on the body load fluctuations. Such as burns and side effects have been reported by system instability and then therapeutic effect is insufficient. During treatment, objective information about the status of the patient was no. Because of treatment methods are subjective, and so tailored treatments were impossible. In this paper, high frequency medical system with sinusoidal frequency characteristics without distortion of the Push pull switching scheme for pain relief therapy was designed. And control circuit that was designed by feedback using the output changes according to the body-load fluctuation. Last, power circuit for efficient control the heat generated from the hardware was proposed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.439-444
• /
• 2004

The important problem in high speed spindle is to reduce and minimize the thermal effect by motor and ball bearings. In this study. the effects of bearing preload and cooling for high speed spindle with high frequency motor are investigated. A high speed spindle is composed of angular contact ball bearings, high frequency motor, grease lubrication, oil jacket cooling, and so on. Heat generation of the bearing and the high frequency motor are estimated from the theoretical and experimental data. The thermal analyses of high speed spindle to minimize the thermal effect and maximize the cooling effect are carried out under the various cooling conditions and preload. Method of variable bearing preload and cooling can be useful to design the high speed motor spindle. The results show that the optimal preload and cooling are very effective to minimize the thermal displacement by motor and ball bearing.

• 전기학회논문지
• /
• 제65권1호
• /
• pp.81-87
• /
• 2016

An LCL-type Isolated dc-dc converter operating for constant output voltage is analyzed, including the effect of a high frequency transformer using ac complex circuit approximation. Its solution is derived and is used to obtain the characteristics of the proposed converter. The analyses show through converter modeling, phasor diagram and gain comparison that inclusion of a high frequency transformer results in introduction of magnetizing inductance and leakage inductances at conventional LCL dc-dc converter with ideal transformer. The theoretical and simulation results are presented in case of the wide variations in input voltage and load current in detail. Analysis and simulation results observed that introduction of a transformer in the dc-dc converter had considerable effect on the performance, especially in the case of low output voltage and large load.

• 한국초전도ㆍ저온공학회논문지
• /
• 제4권2호
• /
• pp.58-62
• /
• 2002

The purpose of this study is to analyze the charging gas effect on the resonance and performance characteristics of the linear compressor for small scale FPFD Stirling refrigerator. To ensure high performance of FPFD type Stirling refrigerator, the operating frequency of the refrigerator should be around the natural frequency of compressor. The gas spring effect which is induced from Pressure change in cylinder due to motion of pistons has significant effect on the natural frequency of the compressor. The numerical results show the linear compressor has high natural frequency when the charging pressure of working fluid is high and the stroke of compressor, current, input power and efficiency of compressor were shown with different operating conditions.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권11호
• /
• pp.583-588
• /
• 2004

We stabilized the frequency and power of a high voltage excited CW CO2 laser on the peak of the Doppler broadened gain curve using the photoacoustic effect generated from the laser itself. The photoacoustic signal is directly coupled from an radio frequency discharge chamber via a capacitor microphone into a detector and a lock-in stabilizer. The frequency stability is estimated to be better then 1.2×10/sup -7/ at the transition P(20) line. The stabilized output power variation was reduced to from 77 % to 3.3 %.

• 한국군사과학기술학회지
• /
• 제13권5호
• /
• pp.775-784
• /
• 2010

In this paper we propose a design method of X band frequency hopping synthesizer in terms of phase noise and settling time with DDS driven PLL architecture, which has the advantages of high frequency resolution, fast settling time and small size. In addition, a noble method is proposed to remove the synthesizer output spurious signals due to superposition effect of DDS. The spurious signal which depend on its normalized frequency of DDS, can be dominant if they occur within the PLL loop bandwidth. We verify that the sources of that spurious signals are quasi-amplitude modulation and superposition effect, and suggest that such signals can be eliminated by intentionally creating frequency errors in the developed synthesizer.

• 한국군사과학기술학회지
• /
• 제6권4호
• /
• pp.100-112
• /
• 2003

This paper presents the transient response analysis of a rotating blade in resonant frequency range. It is shown that the modeling is considered in elastic foundation and friction damping effect. The equations of motion are derived and transformed into a dimensionless form to investigate general phenomena. Numerical results show that the magnitude of friction damping to reduce maximum transient response in near the critical angular speed. The method can be applied to a number of examples of the practical rotating blade system to minimize transient response in resonant frequency range.