본 연구의 목적은 연약지반의 압밀계수 측정에 있어 Piezocone 관입시험을 이용할 때 관입시험자체의 정확성과 시험결과들에 미치는 여러 가지 지반공학적 영향요소들을 고려하려는데 있다. 본 연구의 연구실험방법으로는, Piezocone 관입을 위한 연약모형지반 조성을 위하여 초대형 Slurry Consolidometer에 Free Stress 상태의 Slurry를 45일간 압밀시킨 후 Automatic Computer Control Calibration Chamber (LSU/CALCHAS; Louisiana State University Calibration Chamber System)에 옮긴후 다시한번 압밀시키는 Two-Stage Consolidation Method를 사용하였다 동시에 연약모형지반내에 8개의 Piezometer를 설치하여 Piezocone 관입시 유발되는 지반 내에서의 과잉간극수압의 변환을 측정하였다. 총 25개의 Piezocone 시험중 4개는 Standard 10$\textrm{cm}^2$ Piezocone이고, 나머지 21개는 Miniature Piezocone이 사용되었다. 모형지반은 여러 가지 Boundary Condition들과 Stress Condition 그리고 Stress History등을 고려하여 조성되었다. 또한 Dissipation Test직후의 압밀특성을 확인하기 위하여 0.01초당 한 개이상의 실측점을 측정할 수 있는 Digital-Oscilloscope를 이용하였다. 특히 Dissipation Test, 즉시 Piezocone의 Filter Element에 잡히지 않는 과잉간극수압의 Initial Drop 존재에 관한 기존의 추측을 실제 실험치로 확인할 수 있었다.
As the nuclear power plant has been operated continuously and increased gradually, transportation and storage of spent fuel are seriously considered nowadays. The transportation cask which contains radioactive material needs to be inspected about structural safety. About safety verification, description of IAEA Safety Standards states that cask must withstand hypothetical accident conditions. In this paper, 9m free drop impact analysis was performed for transportation cask and impact limiter by using the finite element methods. Furthermore, we obtained the dynamic behavior of wood to as compared with safety test results, and verified the safety of transportation cask.
The characteristics of an impact load and pressure were experimentally investigated. Drop tests were carried out using a modified Wigley with CB = 0.56. The vertical force, pressures, and vertical accelerations were measured. A 6-component load cell was used to measure the forces, piezo-electric sensors were used to capture the impact pressure, and strain-gauge type accelerometers were used to measure the vertical accelerations. A 50-kHz sampling rate was applied to capture the peak values. The repeatability of the measured data was confirmed and the basic characteristics of the impact load and pressure such as the linearity to the falling height were observed for all of the measurements. A simple formula was derived to extract the physical impact load from the measured force based on a simple mass-sensor-mass diagram, which was validated by comparing impact forces with existing data using the mathematical model of Faltinsen and Chezhian (2005). The effects of the elasticity of the model and change in acceleration during the water entry were investigated. It is interesting to observe that the impact loads occurred and reached peak values at the same time duration after water entry for all drop heights.
This paper presents the results of experimental and numerical research on the slamming phenomenon. Two experimental techniques were proposed in this study. The traditional free drop tests were carried out. However, the free drop tests done in this study using an LM guide showed excellent repeatability, unlike those of other researchers. The coefficients of variation for the drop test done in this experiment were less than 0.1. The other experimental technique proposed in this study was a novel concept that used a pneumatic cylinder. The pneumatic cylinder could accelerate the specimen over a very short distance from the free surface. As a result, high rates of repeatability were achieved. In the numerical study, the development of in-house code and utilization of commercial code were carried out. The in-house code developed was based on the boundary element method. It is a potential code. This was mostly applied to the computation of the wedge entry problem. The commercial code utilized was FLUENT. Most of the previous slamming research was done under the assumption of a constant body velocity all through the impact process, which is not realistic at all. However, the interaction of a fluid and body were taken into account by employing a user-defined function in this study. The experimental and numerical results were compared. The in-house code based on BEM showed better agreement than that of the FLUENT computation when it cames to the wedge computation. However, the FLUENT proved that it could deal with a very complex geometry while BEM could not. The proposed experimental and numerical procedures were shown to be very promising tools for dealing with slamming problems.
프레스드 파우더의 주요 안정성 요인으로 경도와 낙하 안정도가 있다. 일반적으로 탈크가 포함된 프레스드 파우더의 경우 경도와 낙하 안정도를 고르게 충족시키며 사용감도 우수하지만 최근 탈크의 석면 이슈로 인해 대체를 원하는 고객들이 늘고 있다. 따라서 안정성을 유지하면서 사용감도 떨어지지 않는 탈크 프리 프레스드 파우더 제형의 개발이 시급하다. 본 연구에서는 탈크 프리 프레스드 파우더를 만들기 위한 최적의 원료 배합 비율을 찾기 위한 실험을 진행하였다. 파우더에 주로 사용되는 원료들의 특성을 확인하고 비율을 변화시켜 실험하여 명도와 경도를 측정하고 낙하 시험을 실시하였다. 천연 마이카 함량이 합성 마이카보다 많거나, 코팅된 실리카 대신 논 코팅 실리카를 사용할 경우 탈크가 포함된 내용물보다 경도와 낙하 안정도는 낮지만 명도는 유사하였다. 반대로 합성 마이카 함량이 천연 마이카 함량과 동일하거나 높을 경우, 코팅된 실리카 함량이 논코팅 실리카 함량과 동일하거나 높은 경우에 탈크가 포함된 내용물의 경도, 낙하 안정도와는 유사하였으나 명도는 낮게 측정되었다. 탈크가 포함된 내용물보다 경도는 높지만 낙하 안정성은 떨어지는 현상도 발견하여 경도와 낙하 안정성의 상관관계에 대해서는 추가적인 연구가 필요할 것으로 생각된다.
Usage of heavy metal element (Pb, Hg and Cd etc.) in electronic devices have been restricted due to the environmental banning of the European Union, such as WEEE and RoHS. Therefore, it is needed to develop the Pb-free solder plated ribbon in photovoltaic (PV) module. This study described that degradation characteristics of PV module under damp heat (DH, $85^{\circ}C$ and 85% R.H.) condition test for 1,000 h. Solar cell ribbons were utilized to hot dipping plate with Pb-free solder alloys. Two types of Pb-free solder plated ribbons, Sn-3.0Ag-0.5Cu (SAC305) and Sn-48Bi-2Ag, and an electroless Sn-40Pb solder hot dipping plated ribbon as a reference sample were prepared to evaluate degradation characteristics. To detect the degradation of PV module with the eutectic and Pb-free solder plated ribbons, I-V curve, electro-luminescence (EL) and cross-sectional SEM analysis were carried out. DH test results show that the reason of maximum power (Pm) drop was mainly due to the decrease fill factor (FF). It was attributed to the crack or oxidation of interface between the cell and the ribbon. Among PV modules with the eutectic and Pb-free solder plated ribbon, the PV module with SAC305 ribbon relatively showed higher stability after DH test than the case of PV module with Sn-40Pb and Sn-48Bi-2Ag solder plated ribbons.
국내에 많은 도로공사, 공항공사, 항만공사, 구조물 되메우기 공사 등의 토목공사에서 흙의 다짐은 가장 중요한 공정 중 하나이다. 특히 도로공사에서 흙의 다짐공사는 노체다짐과 노상다짐으로 구분하며 다짐도 부족으로 부실공사의 원인으로 작용하기도 하는 중요한 작업이다. 현재는 여러 가지 다짐도 측정방법이 있으나 가장 많이 사용되는 평판재하시험이나 모래치환법에 의한 흙의 단위중량 시험방법을 가장 많이 사용하고 있으나 경제성이 없어 여러 측정방법이 개발되고 있다. 간편한 다짐도 측정 방법의 목적으로 측정기를 개발하고 제작한 것이 자유낙하 관입깊이별 다짐도 시험기(Free-Fall Penetration Test; FFPT)이다. 본 연구에서는 실내시험을 위하여 균질한 시료를 공사현장에서 확보하여 체가름 시험을 통해 흙을 분류하고 입도분석시험과 비중시험을 실시하였다. 자유낙하 관입깊이별 다짐도 시험기(FFPT)의 원리는 지구중력을 이용한 자유낙하 물체의 선단에 설치된 관입 침이 노체 또는 노상의 다짐이 완료된 노면에 관입 되는 깊이를 관측하고 그 위치에 모래치환법에 의한 흙의 단위중량시험을 통하여 다짐도 값을 구하여 분석하고 연관성을 검증하는 것으로 흙의 최대허용입경이 2.36mm로 시험하였으며 $A_1$다짐의 경우는 낙하고 10cm에서 시험한 결과 값으로 추세선을 작성하고 추세선의 결정계수 $R^2=0.8677$ 값을 도출하였으며 $D_2$다짐의 경우는 낙하고 20cm에서 측정 시 결정계수 $R^2=0.9815$ 값이 관측되었다. 자유낙하시험은 낙하높이를 10cm에서 50cm까지 10cm 간격으로 변경을 하면서 시험하였다. 본 연구는 모래치환법에 의한 흙의 단위중량시험을 통하여 얻은 다짐도 값과 FFPT 시험기를 통해 얻은 관입침의 관입깊이와의 연관성을 비교 분석하여 현재의 다짐도 측정방법의 단점인 시간, 장비, 인력의 소모를 최소화하여 경제성을 확보하고 정확성과 간편성을 보장하는 다짐도 측정기 제작으로 여러 공사현장에서 다짐도 측정이 간단하게 진행될 것이다.
휴대폰 및 휴대기기의 낙하 충격에 대한 관심이 증가되고 있는 상황에서 솔더 볼 접합부의 낙하 충격특성은 패드의 종류와 리플로우 횟수에 영향을 받게 되어 이에 따른 신뢰성 평가가 요구된다. 이와 관련한 평 가법으로 일반적으로는 JEDEC에서 제정한 낙하충격 시험법을 사용하고 있으나 이 방법은 고 비용과 장시간이 소모되는 문제가 있어 본 연구에서는 낙하충격 특성을 간접적으로 평가하는 시험항목인 고속 전단시험을 실시하여 리플로우 횟수에 의해 성장하는 금속간 화합물 층과 OSP(Organic Solderability Preservative), ENIG(Electroless Nickel Immersion Gold) 및 ENEPIG(Electroless Nickel Electroless Palladium Immersion Gold) 등 표면처리에 따른 고속 전단특성을 비교, 분석하였다. 그 결과 리플로우 횟수가 증가함에 따라 IMC 층의 성장으로 고속 전단강도와 충격 에너지 값은 점차 감소하였다. 리플로우 횟수가 1회일 때는 ENEPIG, ENIG, OSP 순으로 고속 전단강도와 충격 에너지 값이 높았고 8회일 때는 ENEPIG, OSP, ENIG 순으로 충격 에너지 값이 높게 측정되었다.
PCB와 BGA 패드의 형태가 무연솔더 접합부의 기계적 특성에 미치는 영향을 연구하었다. 현재 BGA/PCB 패드의 형태는 NSMD (Non-Solder Mask Defined)와 SMD (Solder Mask Defined) 두 가지 구조로 형성되어 있다. 본 연구에서는 OSP 도금처리한 무연솔더(Sn-3.0Ag-0.5Cu, Sn-1.2Ag-0.5Cu)의 패드 형태를 NSMD, SMD로 달리하여 낙하충격시험, 굽힘충격시험, 고속전단시험을 통한 솔더 접합부의 기계적 특성을 연구하였다. 낙하충격과 굽힘충격시험의 경우 패드 구조에 따른 솔더볼 접합부의 특성수명은 동일한 경향을 나타내었으며, 솔더접합부의 기계적 특성은 SMD가 NSMD보다 우수하였다. 이 이유는 SMD의 경우 낙하충격 시험과 고속 전단시험 모두 IMC에서 파단이 일어난 반면에 NSMD의 경우 낙하충격 시험 후의 파단면은 패턴을 감싸고 있는 랜드 상단 모서리 부분에서 파단이 일어났기 때문인 것으로 판단된다. 전단시험의 경우에는 NSMD 접합부에서 패드 lift현상이 발생하였다. 따라서 BGA/PCB의 패드구조의 조합은 SMD/SMD > SMD/NSMD > NSMD/SMD > NSMD/NSMD 순으로 기계적 특성 수명이 우수하였다.
Diesel particulate trap is a core technology for the reduction of PM from diesel vehicles This study presents the features and the characteristics of DPF system when using pellet type filters. In comparison with wall-flow filter, the pellet filter has the advantages of cracking free during regeneration and shape flexibility. Experiments are conducted in a test bench simulated as diesel engine exhaust condition. Pressure drop and particle loading rate was compared by using two pellet filters having the porosity of 70% and 0%. Also its regeneration was tested.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.