• Advances in Traditional Medicine
• /
• v.4 no.1
• /
• pp.49-52
• /
• 2004

The total alkaloid fraction of the methanolic extract of Solanum pseudocapsicum unripe fruits was tested for its in-vivo anticancer activity against Dalton's Lymphoma Ascites model in mice. The total alkaloid fraction at 5.0 and 10.0 mg/kg body weight showed significant increase in the mean survival time and the percentage increase in the life span of tumor bearing mice. The increase in the body weight was found to be less than that of the control. However, the treatment at 20 mg/ kg body weight was found to be toxic and showed a decrease in the mean survival time, and body weight when compared to control mice. The antitumor activity observed may be due to the cytotoxic activity of the total alkaloid fraction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.80-89
• /
• 1998

The residual gas in an spark-ignition engine is one of important factors on emissions and performance such as combustion stability. With high residual gas fractions, flame speed and maximum combustion temperature are decreased and these are deeply related with combustion stability especially at idle and NOx emission at relatively high engine load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating parameters. In the present study, the quantitative measurement technique of residual gas fraction was studied by using Fast Response Flame Ionization Detector(FRFID). The measuring technique and model for estimation of residual gas fraction were reported in this paper. By the assuming that the raw signal from FRFID saturates with the same slope for firing and misfiring cycle, in-cylinder hydrocarbon(HC) concentration can be estimated. Residual gas fraction can be obtained from the in-cylinder HC concentration measured at firing and motoring condition. The developed measurement and calibration procedure were applied to the limited engine operating and design condition such as intake manifold pressure and valve overlap. The results show relevant trends by comparing those from previous studies.

• Nuclear Engineering and Technology
• /
• v.48 no.1
• /
• pp.64-71
• /
• 2016

Void fraction is an important parameter in the oil industry. This quantity is necessary for volume rate measurement in multiphase flows. In this study, the void fraction percentage was estimated precisely, independent of the flow regime in gas-liquid two-phase flows by using ${\gamma}-ray$ attenuation and a multilayer perceptron neural network. In all previous studies that implemented a multibeam ${\gamma}-ray$ attenuation technique to determine void fraction independent of the flow regime in two-phase flows, three or more detectors were used while in this study just two NaI detectors were used. Using fewer detectors is of advantage in industrial nuclear gauges because of reduced expense and improved simplicity. In this work, an artificial neural network is also implemented to predict the void fraction percentage independent of the flow regime. To do this, a multilayer perceptron neural network is used for developing the artificial neural network model in MATLAB. The required data for training and testing the network in three different regimes (annular, stratified, and bubbly) were obtained using an experimental setup. Using the technique developed in this work, void fraction percentages were predicted with mean relative error of <1.4%.

• Biomolecules & Therapeutics
• /
• v.19 no.4
• /
• pp.487-492
• /
• 2011

In our previous study, we investigated Chenopodium album Linne (CAL) ethanol extract and its fractions on anti-gastritic actions using the HCl/ethanol and indomethacin induced gastric lesion model and Helicobacter pylori (H. pylori). Based on the results, butanol fraction was most effective among fractions obtained from CAL. This study aims to elucidate the mechanisms of butanol fraction, and betaine as a constituent of the butanol fraction, on gastritis and anti-gastric cancer cell growth. First, we examined antioxidant properties using hydrogen peroxide and superoxide radical, and we found that butanol fraction and betaine may be good antioxidants. Second, cytotoxicity was assessed by measuring cell viability and 4,6-diamidino-2-phenylinodole dihydrochloride (DAPI) staining of human gastric cancer cells (AGS cells). We also examined the relationship between the cytotoxicity and intracellular $Ca^{2+}$ signaling mechanism. The butanol fraction demonstrated cell viability 71.49% at the concentration of 100 ${\mu}g/ml$ and increased intracellular $Ca^{2+}$ concentration in a dose dependent manner. Finally, we observed the mucus content as a defensive factor and gastric secretion as an aggressive factor, and found that the mucus content noticeably increased when treated with butanol fraction and betaine and gastric secretion decreased when treated with betaine in vivo study. From these results, we suggest that CAL butanol fraction and betaine may have protective effects on gastritis.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.37 no.4
• /
• pp.197-209
• /
• 2012

This paper studies an emergency service vehicle location problem, where minimum reliability level pre-specified at each demand point is assured. Several models are suggested depending on the busy fraction, which is the time proportion of unavailability for the ambulances. In this paper a new model on computing the busy fraction is suggested, where it varies depending on the distance between the demand point and ambulances, hence it may respond the more realistic situation. The busy fraction for the ambulance location determined by the optimization model is computed by the simulation, and updated through the iterative procedure. It has been shown that the performances of the solutions obtained by the algorithm suggested for the instances appeared in the literature.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.660-665
• /
• 1993

An elastic model is developed to predict the average thermal residual stresses in the matrix and fiber of a misoriented short fiber composite. The thermal residual stresses are induced by the mismatch in the coefficient of the thermal expansion of the matrix and fiber when the composite is subjected to a uniform temperature change. The model considers two special cases of fiber misorientation ; two-dimensional in-plane and three-dimensional axisymmetric. The analytical formulation of the model is based on Eshelby's equivalent inclusion method and is nuque in that it is able to account for interactions among fibers. The model is more general than past models and it is able to treat prior analyses of the simpler composite systems as extram cases. The present model is to investigate the effects of fiber volume fraction, distribution type, distribution cut-off angle, and aspect ratio on thermal residual stress for both in-plane and axisymmetric fiber misorientation. Fiber volum fraction, aspect ratio, and disturbution cut-off angle are shown to have more significant effects on the magnitude of the thermal residual stress than fiber distrubution type for both in-plane and axisymmetric misorientation.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.241-246
• /
• 1996

An analytical model to calculate rate of vapor generation due to heterogeneous wall nucleation in flashing flow is developed. In the present model, an important parameter of the vapor generation term, i.e. nucleation site density is calculated by integrating its probability distribution function with respect to active cavity radius. The limits of integration are minimum and maximum active cavity radii, and these are formulated using an active cavity model for nucleate boiling. This formulation, therefore. can statistically account for the effect of surface specific thermo-physical and geometric conditions on the vapor generation rate and flashing inception. For verifying the adequacy of the present model, steady state two-fluid and the bubble transport equations are solved with applicable constitutive equations. The applicable region of the bubble transport equation is also extended to churn-turbulent flow regime to predict interfacial area concentration at high void fraction. Predicted results in terms of axial pressure and void fraction profiles along the channels are compared with experimental data of Super Moby Dick and BNL Reasonable agreements have been achieved and this shows the applicability of the present model to flashing flow analysis.

• Journal of the Korean Society of Visualization
• /
• v.9 no.4
• /
• pp.74-79
• /
• 2011

In this study the change of free surface vortex is represented at different times according to height of water and with or without curtain wall installation. The air volume fraction is investigated at each condition of water level and the influence about creation of vortex is analyzed. The height of sump intake is taken as 100mm and the water level is divided into 5 steps. The sump model is the TSJ model and the curtain wall is applied by HI standard of America. The results shows that the free surface vortex can be identified on the isotropic surface at air volume fraction 1%~5% and the vortices make an air column from the free surface to the sump intake and are created and destroyed repeatedly. In the higher water level, less air is absorbed into the intake pipe. After curtain wall installation, the suction rate of the air volume fraction is decreased by 6.7%. The result of the vortex motion according to time, works on a cycle.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.1
• /
• pp.16-24
• /
• 2005

Mathematical model was developed to verify a sequential particle removal taking place in a granular media gravity filter. Consequential multi-layer filtration cycle model was applied to verify the fraction of filter effluent particles that are filter influent particles that were never removed as well as the fraction of filter effluent particles that were detached after deposition were performed through laboratory experiments. Three sizes of marker particles were injected ahead of the filter column as a pulse in the presence of four sizes of polystyrene particles that were used as a primary source of particles in the raw suspension to investigate particle attachment alone in contrast to net removal from attachment and detachment. Microscopic counting of filter effluent particles was assumed to reflect attachment. Experimental results indicated that particle detachment is significant beginning from the early phase of filtration. For each size of fluorescent microspheres at one filter depth, fluorescent microsphere removal increased with filter runtime to a maximum due to ripening. The detached fraction of effluent particles increased with particle size and filter depth. The presence of detached particles and the increasing fraction of detached particles in deeper bed were confirmed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.66-69
• /
• 2005

Mechanical strength of functionally graded composite plates that composed of ceramic, functionally graded material and metal layers is investigated using 3-D finite element method. In FGM layer, material properties are assumed to be varied continuously in the thickness direction according to a simple power law distribution in terms of the volume fraction of a ceramic and metal. The 3-D finite element model is adopted by using an IS-node solid element to analyze more accurately the variation of material properties in the thickness direction. Numerical results are compared with those of the previous works. In addition, the displacements, the tensile stresses and the compressive stresses are analyzed for the variation of FGM thickness ratio and volume fraction distribution.Mechanical strength of functionally graded composite plates that composed of ceramic, functionally graded material and metal layers is investigated using 3-D finite element method. In FGM layer, material properties are assumed to be varied continuously in the thickness direction according to a simple power law distribution in terms of the volume fraction of a ceramic and metal. The 3-D finite element model is adopted by using an IS-node solid element to analyze more accurately the variation of material properties in the thickness direction. Numerical results are compared with those of the previous works. In addition, the displacements, the tensile stresses and the compressive stresses are analyzed for the variation of FGM thickness ratio and volume fraction distribution.