• Journal of Korean Society of Water and Wastewater
• /
• v.11 no.4
• /
• pp.43-53
• /
• 1997

In this research, the synthetic livestock wastewater was prepared to study the characteristics of organic matter removal, the change of VFA production, and the amount of gas production with respect to the change of ammonium nitrogen concentration in the waste using anaerobic fixed bed process, which is an anaerobic biofilm process. The HRT and operation temperature were 1 day and $35{\pm}1^{\circ}C$, respectively. Also, the characteristics of organic matter removal and the inhibitory effect on microorganism in the anaerobic process were studied on the organic loading and ammonium nitrogen concentration. The results obtained were as follows: For COD loading of $10kg/m^3$-day and five levels of ammonium nitrogen concentration ranging from 1,000 to 5,000 mg/L, organic removal efficiencies were about 81, 74, 67, 58, and 51%, and gas productions were 3,860, 3,520, 3,240, 3,020, and 2,790 ml/l-day, respectively. Average methane contents in the gas produced on COD loading of $10kg/m^3$-day was about 76%. Throughout the whole period of experiment, remaining VFA (as COD base) in the effluent was over 90% of remaining COD. This result indicated the inhibitory effect of high concentration of ammonium nitrogen through the facts that accumulated VFA was almost COD and organic removal efficiency decreased also with the increase of ammonium nitrogen. Especially, that implys which high concentration of ammonium nitrogen not only inhibits methane forming bacteria, but also acid forming bacteria.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.462-462
• /
• 2014

The effect of rear passivation for passivated emitter and rear cell (PERC) using ozone and H2O oxidant of atomic layer deposited (ALD) Al2O3 was studied by post-annealing in N2 and forming gas ambients. Rear surface of PERC solar cell was passivated by Al2O3 grown by ALD with ozone and H2O oxidant. Al2O3 grown by ALD with ozone oxidant has been known to have many advantages, such as lower interface defects, low leakage current density. Its passivation quality is better than Al2O3 with H2O. Al2O3 layer with 10 nm and 20 nm thickness was grown at $150^{\circ}C$ with ozone oxidant and at $250^{\circ}C$ with H2O oxidant. And then each samples were post-annealled at $450^{\circ}C$ in N2 ambients and at $850^{\circ}C$ in forming gas ambients. The passivation quality was investigated by measuring the minority carrier lifetime respectively. We examined atomic layer deposited Al2O3 such as growth rate, film density, thickness, negative fixed charge density at AlOx/Si interface, and reflectance. The influences of process temperature and heat treatment were investigated using Sinton (WCT-120) by Quasi-Steady State Photoconductance (QSSPC) mode. Ozone-based ALD Al2O3 film shows the best carrier lifetime at lower deposition temperature than H2O-based ALD.

• Journal of Korea Foundry Society
• /
• v.40 no.2
• /
• pp.34-42
• /
• 2020

The effects of the initial balancing pressure, filling pressure and maximum build-up pressure on the casting characteristics of the thick-wall thickness casting during the counter-pressure casting process were investigated. Water model experiment and a computer simulation were carried out to evaluate the characteristics during the filling and solidification stages in counter-pressure casting (CPC); as a reference, the low-pressure casting (LPC) process was used. The average dendrite cell size decreased with an increase in the solidification rate and maximum build-up pressure. A turbulent flow occurred during the filling stage of the LPC process, resulting in the formation of inner gas, while a lamellar flow pattern dominated during the CPC process and was more evident with an increase in the initial balancing pressure, improving the mechanical properties of the castings.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.8
• /
• pp.815-823
• /
• 2013

The hot curvature forming of large aluminum plates is a process used to produce spherical liquefied natural gas (LNG) tanks. In this study, we describe a method to determine the optimum shape of blanks to minimize the root gap in the forming process. The method proposed in this study was applied to a small-scale model for thick plates with a curvature of 1500 mm and thickness of 6 mm. First, the shape of the curved shells was determined as the target shape, and then a coordinate transform was used to determine the optimum blank shape, which was then iteratively modified using the results of finite element method (FEM) simulations, including heat transfer, until the shape error was minimized. Experiments in forming using Al5083 thick plate were carried out, showing that the method can determine the optimum blank shape within an allowable root gap of 0.1 mm.

• Journal of Powder Materials
• /
• v.13 no.6 s.59
• /
• pp.408-414
• /
• 2006

[ $MoSi_2$ ] alloys with Al, B or Nb were prepared by an advanced consolidation process that combined mechanical alloying with pulse discharge sintering (complex forming) to improve the mechanical properties. Their microstructure and mechanical properties were investigated. The $MoSi_2$ alloys fabricated by complex forming method showed very fine microstructure when compared with the sample sintered from commercial $MoSi_2$ powders. Alloys made from powders milled in Ar gas had fewer silica or alumina phases as compared to their counterparts sintered from powders milled in air. In densification of the sintered body, addition of B was more effective than Al or Nb. Both Victors hardness and tensile test indicated that the alloy fabricated by the complex forming method showed better properties than the sample sintered from commercial $MoSi_2$ powders. The Al added alloy sintered from the powders milled in air had the superior mechanical properties due to the suppression of $SiO_2$ and formation of fine $Al_2O_3$ particles.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.46.2-46.2
• /
• 2017

We will present a discovery of an elliptical jellyfish galaxy in Abell 2670 (Sheen et al. 2017, ApJL, 840, L7). Our MUSE IFU spectra revealed a rotating gas disk in the center of the galaxy and long ionised gas tails emanating from the disk. Its one-sided tails and a tadpole-like morphology of star-forming blobs around the galaxy suggested that the galaxy is experiencing strong ram-pressure stripping in the cluster environment. Stellar kinematics with stellar absorption lines in the MUSE spectra demonstrated that the galaxy is an elliptical galaxy without any hint of a stellar disk. Then, the primary question would be the origin of the rich gas component in the elliptical galaxy. A plausible scenario is a wet merger with a gas-rich companion. In order to investigate star formation history of the system (the galaxy and star-forming blobs), we derived star-formation rate and metallicity from the MUSE spectra. Photometric UV-Optica-IR SED fitting was also performed using GALEX, SDSS, 2MASS and WISE data, to estimate dust and gas masses in the system. For a better understanding of star formation history and environmental effect of this galaxy, FIR/sub-mm follow-up observations are proposed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.3
• /
• pp.172-177
• /
• 2014

Industrial, medical, environment and agriculture application of pulse power technology have been developing rapidly in many field. In order to make use in the form of pulses is applied to the pulse forming technique. At this time, spark gap is generally used for the pulse forming. Spark gap may be possible to simulate the shape of the electrode, to know the uniform or non-uniform electric field of the electrode structure. Further, it can be determined using Paschen's law applied pressure of the insulating gas in accordance with the voltage which is created using the value of the electric field. In this paper, we tried to found using a formula and the simulation process to determine the pressure. The value of the electric field is different according to the shape of the electrode. So, the range of pressure applied also varies. In order to withstand the 100 kV with a gap of 5 mm, the nitrogen gas must be applied to about 7 bar in the electrode structure. On the other hand, in the same conditions, Sulfur hexafluoride gas must be applied to about 2 bar. Consequently, the Sulfur hexafluoride gas has a higher insulation properties than nitrogen gas may be applied to low pressure at the same conditions.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.704-709
• /
• 2019

In this paper, the electrical characteristics of tunneling field effect transistor(TFET) was studied for different annealing conditions. The TFET samples annealed using hydrogen forming gas(4 %) and Deuterium($D_2$) forming gas(4 %). All the measurements were conducted in noise shielded environment. The results show that subthreshold slope(SS) decreased by 33 mV/dec after annealing process compared to before annealing. Under various temperature range, the noise is improved by average of 31.2 % for 10 atm Deuterium gas at $V_G=3V$ condition. It is also noticed that, post metal annealing with $D_2$ gas reduces the noise by average of 30.7 % at $I_D=100nA$ condition.

• KSBB Journal
• /
• v.13 no.5
• /
• pp.477-482
• /
• 1998

A biosensor with PZT piezoelectric ceramic crystal was developed for the detection of formaldehyde gas. Poled PZT piezoelectric ceramic disk was made from ZrO2, TiO2 and Nb2O5, together with the addition of PbO and polyvinyl alcohol, through various processes of mixing, calcination drying, crushing, forming, sintering, polishing, ion coating and poling. Oscillator circuit of sensor was made of operational amplifier(AD811AN). Formaldehyde dehydrogenase was immobilized onto a piezoelectic ceramic crystal, together with the cofactors, reduced glutathione and nicotinamide adenine dinucleotide. The effect of flow rate on the sensitivity was determined by varing the flow rate of carrier gas from 24.7mL/min to 111.7mL/min through detector cell. The results indicated that as the flow rate was increased, the recovery rate was increased. And a significant increase in the sensitivity was observed in enhanced flow rate of carrier gas. Frequency difference(ΔF) of immobilized PZT piezoelectic disk increased proportionally to the concentration gas and reproduced to repeated exposures of formaldehyde gas(28ppm, Δ68Hz).

• Journal of the Korean Solar Energy Society
• /
• v.27 no.4
• /
• pp.51-58
• /
• 2007

Gas hydrate is a special kind of inclusion compound that can be formed by capturing gas molecules to water lattice in high pressure and low temperature conditions. When referred to standard conditions, $1m^3$ solid hydrates contain up to $172Nm^3$ of methane gas, depending on the pressure and temperature of production. Such large volumes make natural gas hydrates can be used to store and transport natural gas. In this study, three-phase equilibrium conditions for forming methane hydrate were theoretically obtained in aqueous single electrolyte solution containing 3wt% NaCl. The results show that the predictions match the previous experimental values very well, and it was found that NaCl acts as an inhibitor.