• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.52-56
• /
• 2013

The purpose of this study is to evaluate the influence of form-oil on steam-cured concrete surface condition. Based, viscosity(high, medium, low) and flash point($26^{\circ}C$, $70^{\circ}C$) of form oil were considered as test variables. The digital image process method was applied for the extraction of air-void area from concrete surface. Test result showed that oil-based form oil reduced air-void by approximately 46% compared to water-based form oil, and the higher the viscosity was, the smaller air-void rate was. In addition, it was conformed that flash point of form oil had a considerable influence on the surface condition of steam-cured concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.197-202
• /
• 1999

The properties of surface-glossing of exposed concrete with the kinds of form materials and form oil are investigated under various slump value. According to the experimental results, surface-glossing has high value with the increase of slump. In case of surface-glossing with the kind of the form, the form made of acryl has the best performance among the form kinds tested in this experiment. The order of surface-glossing is follows ; fancy plywood > metal form > plywood. Water solution type form oil has better performance in surface-glossing than oil solution type form oil. Also, surface-glossing get worse with the elapse of age.

• Journal of Microbiology and Biotechnology
• /
• v.18 no.9
• /
• pp.1522-1528
• /
• 2008

The morphogenetic behavior of a tropical marine Yarrowia lipolytica strain on hydrophobic substrates was studied. Media containing coconut oil or palm kernel oil (rich in lauric and myristic acids) prepared in distilled water or seawater at a neutral pH supported 95% of the cells to undergo a transition from the yeast form to the mycelium form. With potassium laurate, 51 % of the cells were in the mycelium form, whereas with myristate, 32% were in the mycelium form. However, combinations of these two fatty acids in proportions that are present in coconut oil or palm kernel oil enhanced the mycelium formation to 65%. The culture also produced extracellular lipases during the morphogenetic change. The yeast cells were found to attach to the large droplets of the hydrophobic substrates during the transition, while the mycelia were associated with the aqueous phase. The alkane-grown yeast partitioned more efficiently in the hydrophobic phases when compared with the coconut oil-grown mycelia. A fatty acid analysis of the mycelial form revealed the presence of lauric acid in addition to the long-chain saturated and unsaturated fatty acids observed in the yeast form. The mycelia underwent a rapid transition to the yeast form with n-dodecane, a medium-chain aliphatic hydrocarbon. Thus, the fungus displayed a differential behavior towards the two types of saturated hydrophobic substrates.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.66-71
• /
• 2011

Various single solvents were tested to find the effective solvent for the extraction of algae oil from wet-form Chlorella minutissima. In the case of single solvents, their extractabilities for algae oil were increased with their polarity because the water in wet algae cell is to form a solvent shell around the lipids. Based on these results, the wet-form algae samples were treated with a polar alcohol solvent and then a nonpolar solvent was added in algae residue. In the algae oil extraction by ethanol/n-hexane, total lipid contents were 40-50% and composition of triglyceride in extracted oil was 46.50%. Considering solvent toxicity of conventional solvent mixture such as chloroform and methanol for algae oil extraction, the ethanol/n-hexane system was identified as the effective one for the oil extraction from wet-form Chlorella minutissima.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.332-335
• /
• 1995

Electrification pipe modeled on the oil path of the high power transformer is designed and manufactured. Distributions of oil flow velocity are simulated as spacer form in the electrification pipe. Streaming currents are investigated as each electrification pipe. The surface oil velocity of spacer is small the streaming current.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.77-78
• /
• 2018

Form-work is a must for construction work. In order to secure the best condition of the form surface and to increase the number of times, the form releasing agent is applied during the process of the form-work. The base oil of the form release agent which has been used already uses the oil which directly or indirectly affects the natural environment and the concrete. In this study, the basic study on the form release agent for concrete was carried out only for the effect of adhesion. The adhesive force of the tile is measured by the mortar to determine the change of the releasing agent and the adhesive strength.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.6
• /
• pp.456-464
• /
• 2016

To design the modified hull form with relatively unfavorable dimensions and constraints than the parent ship the stepwise design was applied. In each design step the resistance characteristics was estimated by numerical calculations using CFD programs as Wavis 1.4, Wavis 2.1 and Fluent 12.1. The wave profiles along hull surface by potential flow calculations were investigated to improve wave resistance by modifying the bow shapes. To improve the stern shapes with a point of viscous form resistance the pressure distributions on hull surface and the limiting streamlines are investigated by viscous flow calculations. The design objectives such as shortening the LBP, enlarging the propeller tip clearance, moving forward of the LCB location and increasing the displacement were applied by stepwise to develop the new hull form of DWT 75,000 product oil carrier. Finally a new hull form was developed without the resistance performance loss compared with the parent ship.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.10-11
• /
• 2019

The purpose of this study is to validate the environmental performance of the 'eco-friendly lightweight form' in the construction process. Unlike existing euro form and aluminum form, the proposed form does not require form oil during the process of concrete casting and is lightweight because it is made of engineering plastic. Therefore, eco-friendly lightweight form will reduce the $CO_2$ emissions in the construction process. To verify the hypothesis, the study compared existing forms and eco-friendly light weight form's $CO_2$ emissions in each stage in construction process when using 1,000 forms and 100 times from the LCI(Life Cycle Inventory) data. The total $CO_2$ emissions of the eco-friendly light weight form were 30,487kg $CO_2$, which equated to about 58% and 20% less emissions than the euroform and aluminum form. The result of the study verified that the eco-friendly lightweight form was effectively reduced $CO_2$ emission in the construction process.

• Journal of the Korea Concrete Institute
• /
• v.12 no.4
• /
• pp.15-22
• /
• 2000

The objective of this study is to investigate the degree of surface-glossing of flowing concrete, varying with W/C, types of forms and form oils. According to the experimental results, the degree of surface-glossing of flowing concrete is turned out to be higher than that of base concrete, as the slump increases. The degree of surface-glossing of concrete with 40% of W/C is higher than that with 50%. The orders of degree of surface-glossing with the types of forms are as follows : acryle > fancy plywood > metal form > plywood. When water solution type form oil is applied to the surface of forms, we can achieve higher degree of surface-glossing. It shows that the degree of surface-glossing decreases with elapsed time.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.45 no.2
• /
• pp.128-133
• /
• 2000

This study was carried out to investigate the effect of forms and levels of nitrogen fertilizer on plant growth and essential oil production of Agastache rugosa. Calcium nitrate had more influenced on length and width of leaves and lateral branch length than did urea. When nitrogen fertilizer level was increased from 12 kgN/I0a to 24kgN/I0a, plant growth was stimulated and dry matter of leaf and inflorescence were increased. Top dry matter of plant with calcium nitrate treatment (38.4 g) was heavier than that of urea treatment (32.8 g). Interactions among accession and nitrogen form and nitrogen rate were not significantly different for top dry matter. The forms and rate of nitrogen fertilizer did not affect estragole content. The estragole contents was higher in leaf (91.8%) than that of inflorescence (81.3%). While the essential oil content was not affected by different nitrogen forms, nitrogen level affected the essential oil contents positively by increasing dry matter. Essential oil yield was not affected by accession or nitrogen form, but by nitrogen rate. With increasing N application from 12kgN/I0a to 24 kgN/I0a, essential oil yield was increased by 95.8 %.