• Korean Journal of Food Science and Technology
• /
• v.15 no.1
• /
• pp.77-89
• /
• 1983

Properties and frying performance of domestic rice bran oil were studied. For this purpose, the analyses on the following characteristics were performed and their comparison with the characteristics of soybean oil was made: fatty acid composition, glycerides, composition, acid value, specific gravity, color, petroleum ether insoluble oxidized fatty acid, viscosity, smoke point, foam test, and water solubility. The results were as follow: 1) Fatty acid composition of domestic rice bran oil by gas chromatography was same as perviously reported, and similar to the fatty acid composition of the rice bran oil in foreign countries. Also the glyceride composition of domestic rice bran oil was analyzed by the methods of TLC, column chromatography, and high performance liquid chromatography. The results were monoglyceride ranged from one to four percent; diglyceride 30-30% and triglyceride 66-80%. Consequently, the composition was proven completely different from that of the other edible oils. 2) The high contents of mono-glyceride in rice bran oil resulted in high values of specific gravity and water-solubility respectively. However, high contents mono glyceride and diglyceride indicated little affection to changes of acid value, color, petroleum ether insoluble oxidized fatty acid, and smoke point on frying. 3) Because of low contents of linoleic acid, domestic rice bran oil was estimated stable on frying, whereas soybean oil was easily polymerized. 4) A serious foaming and low smoke point on Frying in domestic rice bran oil were caused by its impurities. It seems that monoglyceride and diglyceride had little relation with foaming and smoke point. 5) Oils with serious foaming and low smoke point on frying caused a substantial quality loss in terms of flavor and appearance of fried materials.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2004.05a
• /
• pp.45-50
• /
• 2004

In this study, we processed two procedures of application test of filler for special-purpose utility that are new application methods of aerated concrete and properties test of aerated concrete according to mixing ratio because we investigated the better use of aerated concrete as filler for fireproof safety and we proposed basic data about standardization of mixing of aerated concrete. We measured flow and volume change of aerated concrete. And if its volume doesn't change, we added measuring unit weight and compressive strength. To test application of aerated concrete as filler for fireproof safety, we filled up aerated concrete to fireproof safety according to suitable mixing ratio. Then we measured maximum temperature of inner part of fireproof safety in accordance with the standard test of fireproof. According to the results, aerated concrete as filler for fireproof safety could be possibly used. So when we make aerated concrete, we should consider using an adding agent as well as a foaming agent.

• Journal of the Society of Disaster Information
• /
• v.14 no.1
• /
• pp.79-88
• /
• 2018

In this study, the changes of the expansion and strength according to the temperature of the emergency repairing expansion material were examined by cup foaming test and uniaxial compressive strength test, and the accelerated compression creep test was carried out to confirm the long term stability. Ramp & Hold test and accelerated compressive creep test were performed to evaluate the creep performance. The short - term creep test was used to determine the initial creep strain of the expanding material. The isothermal method using time - To evaluate the long - term compressive creep performance.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.355-360
• /
• 2002

The purpose of this study was to remove the excessive air foaming which was produced in mixing the RSLMC(latex-modified concrete with rapid- setting cement) by choosing the best antifoam agent type and the optimized quantity for performance improved RSLMC. A series of RSLMM(latex-modified mortar with rapid-setting cement) experiments were carried out as the basic for RSLMC with the main experimental variables such as antifiamer types(A, B, C, D), antifoamer contents(0, 1, 2, 3%). Air content test and compressive, flexural tests were carried out to measure the improved properties of RSLMM and RSLMC. Chloride ion permeability test was carried out to estimate water permeability resistance. The results of RSLMM showed that the decrease of 50% air content was obtained by admixturing a antifoam agent by 1%. The compressive strength and flexural strength at 3 hours after RSLMC placement were 235kgf/cm$^2$ and 49kgf/cm$^2$, respectively, which exceeded the flexural strength criterion of 45kgf/cm$^2$ in order to open the RSLMC placed to traffic. The chloride permeability using A and C antifoamer at 28 days were below 100 coulombs, which was the permeability rating of negligible according to ASTM.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.2
• /
• pp.153-159
• /
• 2004

This study was focused on evaluating physical properties and SO$_{x}$ removal capability of porous lime filters prepared by a foaming and a gelcasting method. Porosities of lime filters ranged from 55% to 85%, and their mean pore sizes were about 95 ${\mu}{\textrm}{m}$. It was observed that porous lime filters had the continuous pore structure that most pores were inter-connected by many windows. Before SO$_{x}$ removal reaction a surface of porous lime filters was made up of calcium oxide, but after reaction calcium sulfate became a main component. The SO$_{x}$ removal efficiency and the conversion ratio of calcium oxide to calcium sulfate increased according to reaction temperature and porosity. At 100$0^{\circ}C$, SO$_{x}$ removal efficiency of filters was always over 98% regardless of the porosity. In case of the filter with the porosity of 85%, the conversion ratios of calcium oxide increased according to the reaction temperature, and they were in the range 30% to 60%. to 60%.

• Korean Journal of Human Ecology
• /
• v.14 no.5
• /
• pp.821-832
• /
• 2005

The purpose of this study is to investigate bathing habits and behaviors, and to find out consumers' needs for washcloth, which in this case refers to Korean exfoliating cloth for bathing purpose. Subjects of this study were females of 20s to 50s living in urban area. Four hundred and twenty-six (426) women were interviewed with a structured questionnaire. Data were analyzed by ANOVA, factor analysis, correlation analysis, MDS. The results of this study are briefly summarized as follows: The most popular bathing type was shower (84.9%). Personal hygiene was one of the commonest purpose of bathing, and other purposes included health maintenance, stress alleviation, and beauty in order. Dimensions of consumer needs for washcloth were extracted from factor analysis as following properties: tactile, tough, aesthetic, constructive, and hygienic. The preference for washcloth type was related to skin type. "Non-skin damage property" was the most important parameter to choose washcloth and the other parameters included massage effect, tactile property, foaming property, and easy-to-use property.

• Korean Journal of Materials Research
• /
• v.12 no.2
• /
• pp.129-134
• /
• 2002

The optimum condition for fabricating cordierite disc type filter element was deduced. Cordierite monolith was used as starting material for filter element because it has many advantages such as high thermal shock resistance and good catalytic activity compared with $TiO_2$and SiC. The contents of organic additives and foaming agent were optimized to control the porosity and mechanical strength of cordierite filter. Among the required properties to be adopted as filter elements, the pressure drop and NOx removal efficiency were investigated depending on processing variables. It was found that pressure drop depends on particle size distribution of cordierite monolith and organic additives added as forming agent. The pressure drop at 5cm/sec of face velocity was in the range of 15~655mm$H_2O$ at room temperature. The NOx removal efficiency of catalytic filter with $V_2O_5$ as catalyst was over 85% at $450^{\circ}C$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.447-448
• /
• 2009

On this study, the concrete foaming was maximized using Hydrogen peroxide($H_2O_2$) reciprocal decomposition catalyzed by Manganese dioxide($MnO_2$) and Sodium bicarbonate($NaHCO_3$). Also, we study the physical and mechanical properties of lightweight formed concrete through diverse experiment which is to determine the optimal mixing proportion and require strength of the lightweight formed concrete. As a result of an experiment, it is satisefied with overall quality standard on the KS F 4039 and KS F 2459 provision.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1484-1486
• /
• 1998

Recently, extending the local broadcasting and increasing lots of informations, the low-loss communication cable is required in proportion as frequency. The reason of transportation loss causes to using the high frequencies like hundreds of MHz or decades of GHz. For the low transportation loss, it is required the developing-technology of foaming and the high foamed insulator with the dielectric ratio of the nearest to 1. Therefore, there is the purpose of developing the insulating materials for the low dielectric ratio. Also it is important to measure the attenuation, which is one of the important parameters, as the evaluation of transportation characteristic with frequency in the communication cable. In this paper, the result showed that the dielectric ratio(1.4) of the nearest to 1 and low attenuation with high frequency were very related to the transportation and reflection characteristics such as propagation velocity(82.27%), delay time and voltage standing wave ratio(VSWR).

• Journal of the Korean Ceramic Society
• /
• v.45 no.10
• /
• pp.584-588
• /
• 2008

Porous hydroxyapatite(HA) and HA-coated porous $Al_2O_3$ possessing pore characteristics required for bone substitutes were prepared by a slurry foaming method combined with gelcasting. The HA coating was deposited by heating porous $Al_2O_3$ substrates in an aqueous solution containing $Ca^{2+}$ and ${PO_4}^{3-}$ ions at $65{\sim}95^{\circ}C$ under ambient pressure. The pore characteristic, microstructure, and compressive strength were investigated and compared for the two kinds of samples. The porosity of the samples was about 81% and 80% for HA and $Al_2O_3$, respectively with a highly interconnected network of spherical pores with size ranging from 50 to $250{\mu}m$. The porous $Al_2O_3$ sample showed much higher compressive strength(25 MPa) than the porous HA sample(10 MPa). Fairly dense and uniform HA coating(about $2{\mu}m$ thick) was deposited on the porous $Al_2O_3$ sample. Since the compressive strength of cancellous bone is $2{\sim}12$ MPa, both the porous HA and HA-coated porous $Al_2O_3$ samples could be successfully utilized as scaffolds for bone repair. Especially the latter is expected suitable for load bearing bone substitutes due to its excellent strength.