• Membrane Journal
• /
• v.17 no.3
• /
• pp.184-190
• /
• 2007

This study reports on the pervaporation separation of a volatile organic compound(VOC), dichloromethane(DCM) from water using fluorinated copolysiloxaneimide membranes. The copolysiloxaneimide membranes were prepared from 4,4'-(hexafluoroisopropylidene)diphthalic anhydride(6FDA) and two diamines(polysiloxane diamine(SIDA), 2-(perfluorohexyl)ethyl-3,5-diaminobenzene(PFDAB)). By varying the ratio of flexible polysiloxane diamine(SIDA)/rigid fluorinated aromatic diamine(PFDAB) from 0/100 to 100/0 mol%, five copolysiloxaneimide membranes were prepared success- fully. The pervaporation properties of DCM/water were examined in terms of two diamine monomer ratio at room temperature and the feed composition of 0.05 wt% in water. It was found that the increase in SIDA content led to high permeation flux and pervaporation selectivity towards DCM by the enhanced sorption/sorption selectivity and diffusion coefficient/diffusion selectivity due to the increased hydrophobicity and fractional free volume.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.47-51
• /
• 2011

In this study, illite, an environmental friendly, low cost, and high aspect ratio additive, was used to improve flame retardant property of epoxy and it was fluorinated to enhance dispersion of hydrophilic illite in hydrophobic epoxy by introducing hydrophobic functional groups. Fluorination of illite enhanced illite dispersion ill epoxy solution before curing and that in the complex after curing. These enhanced dispersions were attributed to the increased affinity of illite to hydrophobic epoxy solution induced by fluorination of illite and the increased intercalation of epoxy polymer or exfoliation of illite by epoxy curing. Hence, limited oxygen index(LOI) of fluorinated illite/epoxy complex increased by 24%, compared to that of epoxy, suggesting that the preparation of fluorinated illite/epoxy complex increased their flame retardant properties.

• Journal of Adhesion and Interface
• /
• v.20 no.4
• /
• pp.146-154
• /
• 2019

In this study, alkoxysilane-functionalized amphiphilic polymer (AFAP), which have hydrophilic segment and hydrophobic segment functionalized by alkoxysilane group at the same backbone, was synthesized and used as a dispersant and control agent for reaction rate in the preparation of colloidally stable organic-inorganic (O-I) hybrid sols. After reaction with fluorosilane compounds, fluorinated O-I hybrid sols were prepared and coated onto glass substrate to form hydrophobic O-I hybrid coating films through low-temperature curing process. Surface hardness and hydrophobicity of cured coating films were varied with type of solvent and composition of AFAP and fluorinated alkoxysilane compounds. At appropriate solvent and composition of fluorinated alkoxysilane compounds, O-I hybrid coating film having high transparency and surface hardness could be prepared, which could be applicable to cover window of solar cell and displays.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1089-1096
• /
• 2002

Solvolyses rate constants of trimethylacetyl chloride (2), isobutyryl chloride (3), diphenylacetyl chloride (4) and p-methoxyphenylacetyl chloride (5) in 2,2,2-trifluoroethanol (TFE)-water, 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP)-water and TFE-et hanol solvent systems at $10^{\circ}C$ are determined by a conductimetric method. Kinetic solvent isotope effects (KSIE) are reported from additional kinetic data for methanolyses of various substituted acetylchlorides in methanol According to the results of those reactions analyzed in terms of rate-rate profiles,extended Grunwald-Winstein type correlations, application of a third order reaction model based a general base catalyzed (GBC) and KSIE values. Regardless of the kind of neighboring groups (CH3- or Ph-groups) of reaction center, for aqueous fluorinated alcohol systems, solvolyses of 2, 3, 4, and 5 were exposed to the reaction with the same mechanism (a loose SN2 type mechanism by electrophilic solvation) controlled by a similarity of solvation of the transition sate (TS). Whereas, for TFE-ethanol solvent systems, the reactivity depended on whether substituted acetyl chloride have aromatic rings (Ph-) or alkyl groups (CH3-); the solvations by the predominant stoichiometric effect (third order reaction mechanism by GBC and/or by push-pull type) for Ph- groups (4 and 5) and the same solvation effects as those shown in TFE-water solvent systems for CH3- groups (2 and 3) were exhibited Such phenomena can be interpreted as having relevance to the inductive effect ( $\sigmaI)$ of substituted groups; the plot of log (KSIE) vs. ${\sigma}I$ parameter give an acceptable the linear correlation with r = 0.970 (slope = 0.44 $\pm$ 0.06, n = 5).

• Membrane Journal
• /
• v.25 no.5
• /
• pp.447-455
• /
• 2015

In this study, Polysulfone (PSf) and polyetherimide (PEI) as the anion exchange polymers were aminated in the different ratio whereas the polyether ether ketone (PEEK) as the cation exchange polymer was sulfonated. The bipolar membranes of SPEEK (sulfonated PEEK)/APSf (aminated PSf) and SPEEK/APEI (aminated PEI) were prepared by the double-casting method. The surfaces of bipolar membranes were fluorinated in accordance with the amination ratio and applied to produce the hypochlorite. As the amination increased, the hypochlorite concentration is also increased. Typically, for SPEEK/APSf 3 : 1 membrane, the produced hypochlorite concentration was 61.0 ppm and its durability was 220 min for the non-fluorinated membrane while for the fluorinated membrane, the concentration of 58.6 ppm and its durability lasted 570 min. Also for SPEEK/APEI 3 : 1 membrane, the hypochlorite concentrations of 60.1 ppm and 58.3 ppm for before- and after-fluorination, respectively were observed whereas the durability was remarkably developed from 150 min to 440 min. Therefore, the surface fluorination takes an important role for the development of the membrane durability.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.397-403
• /
• 2023

In this study, the effect of the addition of fluorinated surfactant FS-606 on the solubilization of n-hexane by hydrocarbon surfactant CDP-W was investigated. Oil drop contacting experiments revealed that solubilization rate is independent of initial oil drop size and proportional to the initial surfactant concentration, suggesting that solubilization of n-hexane oil by the surfactant mixture of FS-606 and CDP-W is controlled by an interface-controlled mechanism. In addition, the solubilization rate has been shown to increase with an increase in FS-606 composition, reach a maximum, and then decrease with a further increase in FS-606 composition. On the other hand, the interfacial tension between micellar solution and n-hexane oil has been found to decrease with an increase in FS-606 composition, reach a minimum, and then increase with a further increase in FS-606 composition.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.231-237
• /
• 2014

The supercritical fluids (SCFs) have been widely used for material synthesis and processing due to their remarkable properties including low viscosity, high diffusivity and low surface tension. Carbon dioxide is one of the suitable solvents in SCFs processes in terms of its advantages such as easy processibility (with low critical temperature and pressure), inexpensive, nonflammable, nontoxic, and readily available. However, it has generally low solubility for high molecular weight polymers with the exception of fluoropolymers and siloxane polymers. Therefore, hydrocarbon solvents and hydrochlorofluorocarbons have been used for various SCFs process by its high solubility for high molecular weight polymers. In this report, a PMMA/clay nanocomposites were fabricated by using supercritical fluid process. The $Na^+$-MMT(montmorillonites)was modified by a fluorinated surfactant which is able to enhance compatibility with the chlorodifluoromethane(HCFC-22) and thus, improve dispersability of the clay in the polymer matrix. The PMMA/fluorinated surfactant modified clay nanocomposite shows enhanced mechanical and thermal properties which characterized by X-raydiffraction(XRD), Thermo gravimetric analysis(TGA), Dynamic mechanical analysis (DMA) and Transmission electron microscopy (TEM).

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.86-93
• /
• 2013

In this work, the thermal, antibiotic properties and far-infrared emissivity of fluorinated illite embedded polypropylene non-woven fibers (f-illite/PP fibers) were investigated in the presence of 0, 1, 3, 5 and 7 wt% illite powders. The thermal properties of f-illite/PP fibers were studied by thermogravimetric analysis (TGA). Their antibiotic properties were examined by Staphylococcus aureus and Klebsiella pneumoniae test. Their far-infrared emissivity was also investigated by Fourier transform infrared spectroscopy. From the experimental results, thermal, antibiotic properties and far-infrared emissivity of f-illite/PP fibers were improved by increasing fluorinated illite contents and the property values of 5 wt% f-illite/PP fibers were increased remarkably by about 10.3, 41.2 and 9.8% respectively in comparison with PP non-woven fibers having no fluorinated illite additive. This result was interpreted as the development of interfacial adhesion force between the polymer chains due to the fluorination of illite power.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.629-633
• /
• 1998

The synthesis of 1,1-difluoroethane from acetylene as a function of HF/acetylene ratio, contact time and reaction temperature was studied on a fluorinated ${\gamma}-Al_2O_3$. The fluorination of ${\gamma}-Al_2O_3$ was treated with pure HF gas at high temperature. The crystallinity, the porosity, and the acid properties of the prepared samples were examined using XRD, the nitrogen adsorption, pyridine-IR and ammonia-TPD respectively. The activity was enhanced by further fluorination of alumina. The fraction of 1,1-difluoroethane was obtained above 90% at reaction temperature of about $200^{\circ}C$. The ratio of 1,1-difluoroethane to vinylfluoride over fluorinated ${\gamma}-Al_2O_3$ catalyst was increased with the mole ratio of HF/acetylene and contact time, and was found to be the highest ratio at reaction temperature of $200^{\circ}C$.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.378-383
• /
• 2001

An out line of the material process with using the atmospheric pressure glow plasma is described as follows : (1) TiO powder coating with SiO$_2$ (2) Surface treatment of Fluorinated polymers and (3) Surface cleaning of electronic circuit board with using splay type.