• 청정기술
• /
• 제9권4호
• /
• pp.179-187
• /
• 2003

건식 흡착제를 이용한 유동층 공정에 관한 기술은 이산화탄소 처리 비용을 철강하고 효율적으로 운전될 수 있는 신기술이라고 할 수 있다. 따라서, 본 연구에서는 유동층 공정에서 건식 흡착제를 사용할 때 조업변수에 따른 이산화탄소 제어에 대해 살펴보고, 이산화탄소 흡착능과 압력강하에 대해서 고정층 공정과 비교하였으며, 활성탄, 활성 알루미나, 분자체 5A, 분자체 13X의 이산화탄소 흡착능을 각각 살펴보았다. 연구 결과, 유동층 공정의 운전을 위한 기초자료를 얻을 수 있었고, 유속이 증가할수록 유동층 공정은 상대적으로 높은 이산화탄소 흡착능과 낮은 압력강하를 지니는 것으로 나타났다. 그리고, 분자체 5A는 다른 건식 흡착제들보다 1.1~3.0배 파괴점이 늦게 나타났으며, 1.1~2.7배 높은 흡착능을 보였다.

• 한국수소및신에너지학회논문집
• /
• 제23권4호
• /
• pp.337-345
• /
• 2012

To check effects of operating variables on reaction characteristics of WGS catalyst for SEWGS process, water gas shift reaction tests were carried out in a pressurized fluidized bed reactor using commercial WGS catalyst and sand(as a substitute for $CO_2$ absorbent) as bed materials. Simulated syngas(mixed with $N_2$) was used as a reactant gas. Operating temperature was $210^{\circ}C$ and operating pressure was 20 bar. WGS catalyst content, steam/CO ratio, gas velocity, and syngas concentration were considered as experimental variables. CO conversion increased as the catalyst content and steam/CO ratio increased. CO conversion at fluidized bed condition was higher than that of fixed bed condition. However, CO conversion were maintained almost same value within the fluidized bed condition. CO conversion decreased as the syngas concentration increased. The optimum operation condition was confirmed and long time water gas shift reaction test up to 24 hours at the optimum operating conditions was carried out.

• KSBB Journal
• /
• 제17권1호
• /
• pp.26-32
• /
• 2002

세포의 다당류 xanthan을 생산하기 위하여 호기성 박테리아 X. campestris를 9 L 삼상유동층 생물반응기에서 연속적으로 배양하였다. 고점도 배양액에서 공기 기포를 분쇄하기 위하여 직경 8 mm 유리 유동입자를 사용하였다. 반응기 희석률을 증가시킴에 따라 세포 단위질량 당 xanthan 생성속도 및 생성된 xanthan의 분자량은 증가하였다. 산소공급제한이 발생하지 않을 경우 연속발효에서의 xanthan 비생성속도는 회분식 발효에서 제안된 상관식의 예측결과 보다 상당히 높은 값을 보였다.

• Design & Manufacturing
• /
• 제16권2호
• /
• pp.26-32
• /
• 2022

It is known that the fluidized bed incinerator, which is the subject of analysis, shows excellent performance in heat and mass transfer due to excellent mixing and contact performance between fluidized sand and fuel, and also shows relatively good combustion characteristics thanks to good mixing and long residence time for low-grade fuels. have. In this study, air flow analysis is performed to understand the characteristics of co-firing of sludge, waste oil and solid waste in the fluidized bed incinerator, flow characteristics of flue gas, and discharge characteristics of pollutants.The fluidized bed incinerator subject to analysis is a facility that incinerates factory waste and general household waste together with sludge, with a processing capacity of 32 tons/day. to be. In addition, the operation method was designed for continuous operation for 24 hours. As a result, it can be seen that the lower combustion air and the introduced secondary air are changed to a strong turbulence and swirl flow form and exit through the outlet while rotating inside the freeboard layer. The homogeneous one-way flow form before reaching the secondary air nozzle has very high diffusivity with the high-speed jet flow of the nozzle.

• 자원리싸이클링
• /
• 제15권1호
• /
• pp.3-11
• /
• 2006

유동층 열분해로에서 상수리나무의 급속열분해를 수행하고 생성된 바이오오일의 물리화학적 특성을 GC/MS를 이용하여 분석하였다. 유동층 열분해로에서 얻어진 상수리나무와 낙엽송의 바이오오일 수율은 각각 $350^{\circ}C,\;400^{\circ}C$에서 최대치를 보였으며 이는 두 수종간의 셀룰로오스 함량차이에 기인하는 것으로 추정된다. 최적온도 이상에서는 반응온도가 증가할수록 프리보드에서의 2차 열분해에 의하여 촤와 오일의 수율이 감소하였고 가스상 성분과 수분의 함량이 증가하였다. 유등층 열분해로에서 시료의 투입량은 생성물의 수율과 조성에는 큰 영향을 주지 않았으며 이는 충분한 혼합이 이루어지기 때문으로 판단되었다.

• 공업화학
• /
• 제9권2호
• /
• pp.278-285
• /
• 1998

배출가스중의 $SO_2$ 제거를 위하여 다양한 금속산화물로 구성된 천연망간광석, 철광석, $CuO/{\gamma}-A1_2O_3$ 등을 흡착제로 사용하여 고정층반응기에서 흡착용량실험을 하였다. 또한 흡착제중 흡착용량이 떨어지는 철광석을 제외한 두 가지 흡착제를 이용하여 유동층반응기에서 유속, 온도, 입자크기 등의 조업조건에 따른 $SO_2$ 흡착실험을 수행하였다. 모든 흡착제에서 온도가 증가할수록 흡착량이 증가하는 화학흡착반응을 보였고 유동층반응기에서 $U_o/U_{mf}$ 및 $U_o-U_{mf}$와 같은 유속조건에 따라 입자 크기에 따른 흡착량의 변화가 다르게 나타났으며 유동층반응기 성능식으로부터 반응속도상수를 얻었다. 이 실험을 통하여 천연망간광석이 유동층반응기에서 $SO_2$ 흡착제로의 사용가능성을 확인할 수 있었다.

• 한국산학기술학회논문지
• /
• 제10권7호
• /
• pp.1446-1452
• /
• 2009

직경 340mm, 높이 195mm의 원심유동층에서 10.5${\mu}m$와 21.5${\mu}m$의 평균직경을 갖는 $Al_2O_3$를 유동물질로 하여 400, 600, 800, 1000rpm으로 기포의 거동을 규명하고자 2중사진 촬영에 의해 유동가시화현상을 실험하였다. 실험결과, 본 실험 범위에서 원심유동층에서 기포의 거동은 회전수에 영향을 받는 것을 알 수 있었으며, 회전수가 증가함에 따라 기포가 발생하기 시작하는 속도는 증가하였으나 기포의 직경은 감소하는 것을 알 수 있었고 기포의 크기는 상대적으로 작게 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.30-36
• /
• 2006

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a batch type fluidized-bed to investigate the drying characteristics of sawdust as a raw material for bio-fuel. The minimum fluidization air velocity was increased as particle size was increased. It took about 21 minutes and 8 minutes to dry 0.08 m-deep bed of particles with average particle size of 1.3 mm from 100% to 10% moisture content at air temperature of $20^{\circ}C$ and $50^{\circ}C$, respectively.

• KSBB Journal
• /
• 제13권2호
• /
• pp.141-146
• /
• 1998

To remove the low concentration of methane biologically, a three phase fluidized bed bioreactor immobilized with Methylosinus trichosporium OB3b was used. Optimum pH, temperature and bed height for the operation were pH7.0, 30$^\circ C$ and 150cm, respectively. For the inlet methane concentration of 100-400ppm and flow rate of 2-4L/min, the removal efficiencies of the bioreactor using the activated carbon as a carrier were the range of 54-71%, whereas those using the biosand were the range of 45-56%. It was found that activated carbon was more efficient than the biosand for the removal of methane. When aeration tank was equipped with the bioreactor, the removal efficiency increased to 6-13% and maximum removal rate obtained in the experiment was 1184mg.CH$_4$/min.

• 플랜트 저널
• /
• 제6권2호
• /
• pp.70-77
• /
• 2010

This study investigated the characteristics of co-combustion of mixed anthracite (domestic and Vietnam) and bituminous coal (Sonoma, Australia) at circulating fluidized bed boiler in Donghae thermal power plant when mixing ratio of bituminous coal is variable. Co-combustion of bituminous coal contributes to improvement in general combustion characteristics such as moderately retaining temperature of furnace and recycle loop, reducing unburned carbon powder, and reducing discharge concentration of NOx and limestone supply owing to improvement in anthracite combustibility as the mixing ratio was increased. However, bed materials were needed to be added externally when the mixing ratio exceeded 40% because of reduction in generating bed materials based on reduction in ash production. When co-combustion was conducted in the section of 40 to 60% in the mixing ratio while the supplied particles of bituminous coal was increased from 6 mm to 10 mm, continuous operation was shown to be possible with upper differential pressure of 100 mmH2O (0.98 kPa) and more without addition of bed materials for the co-combustion of mixed anthracite and bituminous coal (to 50% or less of the ratio) and that of domestic coal and bituminous coal (to 60% of the ratio).